2022 TOYOTA BZ4X CAN

325
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
The blind spot monitor can be
enabled/disabled on of the
multi-information display. ( P.176)
When the Blind Spot Monitor is off, the
driving assist information indicator
( P.169) will illuminate. At this time,
“Blind Spot Monitor OFF” will be dis-
played on the multi-information display.
Each time the power switch is turned to
ON, the Blind Spot Monitor is enabled.
WARNING
■To ensure the system can oper- ate properly
Blind Spot Monitor sensors are installed behind the left and right sides of the rear bumper respectively.
Observe the following to ensure the Blind Spot Monitor can operate cor-rectly.
●Keep the sensors and the sur-rounding areas on the rear bumper
clean at all times.
If a sensor or its surrounding area on
the rear bumper is dirty or covered
w i t h s n o w, t h e B l i n d S p o t M o n i t o r m a y
not operate and a warning message
( P.524) will be displayed. In this sit-
uation, clear off the dirt or snow and
drive the vehicle with the operation
conditions of the BSM function
( P.327) satisfied for approximately
10 minutes. If the warning message
does not disappear, have the vehicle
inspected by any authorized Toyota
retailer or Toyota authorized repairer,
or any reliable repairer.
●Do not attach accessories, stickers
(including transparent stickers), alu- minum tape, etc., to a sensor or its surrounding area on the rear
bumper.
●Do not subject a sensor or its sur- rounding area on the rear bumper to a strong impact.
If a sensor is moved even slightly off position, the system may mal-function and vehicles may not be
detected correctly. In the following situations, have your vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer.
• A sensor or its surrounding area is subject to a strong impact.
• If the surrounding area of a sensor is scratched or dented, or part of them has become disconnected.
●Do not disassemble the sensor.
●Do not modify the sensor or sur-rounding area on the rear bumper.
●If a sensor or the rear bumper needs to be removed/installed or replaced, contact any authorized
Toyota retailer or Toyota authorized repairer, or any reliable repairer.
●Do not paint the rear bumper any color other than an official Toyota color.
Turning the Blind Spot Moni-
tor on/off

326
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
■Vehicles that can be detected by the Blind Spot Monitor
The Blind Spot Monitor uses rear side radar sensors to detect t he following
vehicles traveling in adjacent lanes and advises the driver of the presence
of such vehicles via the indicators on the outside rear view mi rrors.
Vehicles that are traveling in areas that are not visible using the outside
rear view mirrors (the blind spots)
Vehicles that are approaching rapidly from behind in areas that are not
visible using the outside rear view mirrors (the blind spots)
■The Blind Spot Monitor detection areas
The areas that vehicles can be detected in are outlined below.
The range of each detection area is:
Approximately 0.5 m (1.6 ft.) to 3.5 m (11.5 ft.) from either s ide of the
vehicle*1
Approximately 1 m (3.3 ft.) forward of the rear bumper
Approximately 3 m (9.8 ft.) from the rear bumper
Blind Spot Monitor operation

327
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
Approximately 3 m (9.8 ft.) to 60 m (197 ft.) from the rear bumper*2
*1: The area between the side of the vehicle and 0.5 m (1.6 ft.) from the side of the
vehicle cannot be detected.
*2: The greater the difference in speed between your vehicle and t he detected vehi-
cle is, the farther away the vehicle will be detected, causing the outside rear view
mirror indicator to illuminate or flash.
■The Blind Spot Monitor is opera- tional when
The Blind Spot Monitor is operational when all of the following conditions are met:
●The power switch is in ON.
●The Blind Spot Monitor is on.
●The shift position is in a position other
than R.
●The vehicle speed is greater than
approximately 10 km/h (7 mph).
■The Blind Spot Monitor will detect a vehicle when
The Blind Spot Monitor will detect a
vehicle present in the detection area in the following situations:
●A vehicle in an adjacent lane over-takes your vehicle.
●You overtake a vehicle in an adjacent lane slowly.
●Another vehicle enters the detection area when it changes lanes.
■Conditions under which the system will not detect a vehicle
The Blind Spot Monitor is not designed to detect the following types of vehicles and/or objects:
●Small motorcycles, bicycles, pedestri-
ans, etc.,*
●Vehicles traveling in the opposite direction
●Guardrails, walls, signs, parked vehi-
cles and similar stationary objects*
●Following vehicles that are in the
same lane*
●Vehicles traveling 2 lanes away from
your vehicle*
●Vehicles which are being overtaken
rapidly by your vehicle*
*: Depending on the conditions, detec-
tion of a vehicle and/or object may
occur.
■Conditions under which the system may not function correctly
●The Blind Spot Monitor may not detect vehicles correctly in the following situ-ations:
• When the sensor is misaligned due to a strong impact to the sensor or its surrounding area
• When mud, snow, ice, a sticker, etc., is covering the sensor or surrounding area on the rear bumper
• When driving on a road surface that is wet with standing water during bad weather, such as heavy rain, snow, or
fog • When multiple vehicles are approach-ing with only a small gap between
each vehicle • When the distance between your vehi-cle and a following vehicle is short
• When there is a significant difference in speed between your vehicle and the vehicle that enters the detection
area • When the difference in speed between your vehicle and another
vehicle is changing • When a vehicle enters a detection area traveling at about the same
speed as your vehicle • As your vehicle starts from a stop, a vehicle remains in the detection area
• When driving up and down consecu- tive steep inclines, such as hills, dips

328
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
in the road, etc.
• When driving on roads with sharp bends, consecutive curves, or uneven surfaces
• When vehicle lanes are wide, or when driving on the edge of a lane, and the vehicle in an adjacent lane is far away
from your vehicle • When an accessory (such as a bicycle carrier) is installed to the rear of the
vehicle • When there is a significant difference in height between your vehicle and
the vehicle that enters the detection area• Immediately after the Blind Spot Moni-
tor is turned on • When towing with the vehicle
●Instances of the Blind Spot Monitor unnecessarily detecting a vehicle and/or object may increase in the fol-
lowing situations: • When the sensor is misaligned due to a strong impact to the sensor or its
surrounding area • When the distance between your vehi-cle and a guardrail, wall, etc., that
enters the detection area is short • When driving up and down consecu-tive steep inclines, such as hills, dips
in the road, etc. • When vehicle lanes are narrow, or when driving on the edge of a lane,
and a vehicle traveling in a lane other than the adjacent lanes enters the detection area
• When driving on roads with sharp bends, consecutive curves, or uneven surfaces
• When the tires are slipping or spinning • When the distance between your vehi-cle and a following vehicle is short
• When an accessory (such as a bicycle carrier) is installed to the rear of the vehicle
• When towing with the vehicle
*: If equipped
SEA (Safe Exit Assist)*
The Safe Exit Assist is a sys-
tem that uses radar sensors
installed on the inner side of
the rear bumper to help occu-
pants judge if an approaching
vehicle or bicycle may collide
with a door to reduce the pos-
sibility of a collision.
WARNING
■Cautions regarding the use of
the system
●The driver is solely responsible for safe driving. Always drive safely,
taking care to observe your sur- roundings.
●Safe Exit Assist is a supplementary system that, when the vehicle is stopped, informs occupants of the
existence of approaching vehicles and bicycles. As this system alone cannot be used to judge safety,
over-reliance on this system may lead to an accident resulting in death or serious injury.
As the system may not function cor- rectly under certain conditions, visual confirmation of safety with
the passengers’ own eyes and mir- rors is necessary.

329
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
Multi-information display
Turning the Safe Exit Assist on/off
When the system determines that the
possibility of a collision with a door is
high, the target door is displayed on the
multi-information display. Also, if the
door is opened when the outside rear
view mirror indicator is illuminated, a
buzzer will sound as a warning.
Outside rear view mirror indica-
tors
When a vehicle or bicycle which may
collide with a door (other than the back
door) when opened is detected, the
outside rear view mirror indicator on the
detected side will illuminate. If the door
on the detected side is open, the out-
side rear view mirror indicator will blink.
■Outside rear view mirror indicator
visibility
In strong sunlight, the outside rear view mirror indicator may be difficult to see.
■Buzzer
If the volume setting of the audio system is high or the surrounding area is loud, it may be difficult to hear the buzzer.
■Customization
Some functions can be customized. ( P.571)
System componentsWARNING
■To ensure the system can oper- ate properly
Safe Exit Assist sensors are installed behind the left and right sides of the rear bumper respectively. Observe
the following to ensure the Safe Exit Assist can operate correctly.
●Keep the sensors and the sur-rounding areas on the rear bumper clean at all times.
If a sensor or its surrounding area on the rear bumper is dirty or cov-ered with snow, the Safe Exit Assist
may not operate and a warning message will be displayed. In this situation, clear off the dirt or snow
and drive the vehicle with the oper- ation conditions of the SEA function satisfied for approximately 10 min-
utes. If the warning message does not disappear, have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer.
●Do not attach accessories, stickers (including transparent stickers), alu-minum tape, etc., to a sensor or its
surrounding area on the rear bumper.

330
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
The Safe Exit Assist can be
enabled/disabled on of the
multi-information display. ( P.176)
When the Safe Exit Assist is off, the
driving assist information indicator
( P.169) will illuminate. At this time,
“Safe Exit Assist OFF” will be displayed
on the multi-information display.
Each time the power switch is turned to
ON, the Safe Exit Assist is enabled.
When the Safe Exit Assist detects the following vehicles or bic ycles using a
rear side radar sensor, the occupants of the vehicle are inform ed through
an outside rear view mirror indicator, buzzer, display on the m eter, and
voice notification.
WARNING
●Do not subject a sensor or its sur- rounding area on the rear bumper
to a strong impact. If a sensor is moved even slightly off position, the system may mal-
function and vehicles may not be detected correctly. In the following situations, have your vehicle
inspected by any authorized Toyota retailer or Toyota authorized repairer, or any reliable repairer.
• A sensor or its surrounding area is subject to a strong impact.
• If the surrounding area of a sensor is scratched or dented, or part of
them has become disconnected.
●Do not disassemble the sensor.
●Do not modify the sensor or sur- rounding area on the rear bumper.
●If a sensor or the rear bumper needs to be removed/installed or
replaced, contact any authorized Toyota retailer or Toyota authorized repairer, or any reliable repairer.
●Do not paint the rear bumper any color other than an official Toyota color.
Turning the Safe Exit Assist
system on/off
Objects that can be detected by the Safe Exit Assist

331
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
A Vehicle or bicycle which has a high possibility of colliding with a door
(other than the back door) when opened
The areas that vehicles can be detected in are outlined below.
Approximately 45m (145 ft.) rearward from the front door*
*: The faster the speed of the approaching vehicle or bicycle, th e door mirror indica-
tor will turn on or flash, the farther the vehicle or bicycle i s to the door.
■The Safe Exit Assist is operational when
The Safe Exit Assist is operational when
all of the following conditions are met:
●When the EV system is running, less
than 3 minutes have elapsed since the EV system was stopped, or less than 3 minutes have elapsed since a
door was opened and someone has entered the vehicle (the time which operation is possible may be
extended if a door is opened and closed)
●When the Safe Exit Assist is on
●The vehicle is stopped.
●The shift position is in a position other
than R.
■The Safe Exit Assist will detect a vehicle when
The Safe Exit Assist will detect a vehicle
present in the detection area in the fol- lowing situations:
When the vehicle is stopped and a vehi-
cle or bicycle, which is traveling parallel to the vehicle, is approaching within the area that a door opens (other than the
back door)
The Safe Exit Assist detection areas

334
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Use the meter control switches to
enable/disable the Toyota parking
assist-sensor. ( P. 1 7 6 )
1 Press or to select .
2 Press or to select
and then press .
When the Toyota parking assist-sensor
function is disabled, the Toyota parking
assist-sensor OFF indicator ( P.169)
illuminates.
To re-enable the system when it was
disabled, select on the multi-infor-
mation display, select and then
On. If disabled using this method, the
system will not be re-enabled by turning
the power switch off and then to ON.
Turning Toyota parking
assist-sensor on/off
WARNING
■Cautions regarding the use of
the system
There is a limit to the degree of recog- nition accuracy and control perfor-
mance that this system can provide, do not overly rely on this system. The driver is always responsible for paying
attention to the vehicle’s surroundings and driving safely.
■To ensure the system can oper-ate properly
Observe the following precautions.
Failing to do so may result in the vehi- cle being unable to be driven safely and possibly cause an accident.
●Do not damage the sensors, and always keep them clean.
●Do not attach a sticker or install an electronic component, such as a backlit license plate (especially fluo-
rescent type), fog lights, fender pole or wireless antenna near a radar sensor.
●Do not subject the surrounding area of the sensor to a strong impact. If
subjected to an impact, have the vehicle inspected by any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer. If the front or rear bumper needs to be removed/installed or replaced,
contact any authorized Toyota retailer or Toyota authorized repairer, or any reliable repairer.
●Do n ot m od i fy, d is a sse mb l e o r p ai n t the sensors.
●Do not attach a license plate cover.
●Keep your tires properly inflated.
■When to disable the function
In the following situations, disable the function as it may operate even though there is no possibility of a colli-
sion.
●Failing to observe the warnings
above.
●A non-genuine Toyota suspension
(lowered suspension, etc.) is installed.
■Notes when washing the vehicle
Do not apply intensive bursts of water or steam to the sensor area.
Doing so may result in the sensor malfunctioning.
●When using a high pressure washer to wash the vehicle, do not spray the sensors directly, as doing
so may cause a sensor to malfunc- tion.