2022 TOYOTA BZ4X CAN

317
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
The cruise control indicator will illumi-
nate.
2 Using the accelerator pedal,
accelerate to the desired vehicle
speed (approximately 30 km/h
[20 mph] or more), and press
the driving assist switch to set
the set vehicle speed.
The vehicle speed at the moment the
switch is released will be the set vehicle speed.
■Adjusting the set vehicle
speed using the switches
To change the set vehicle speed,
press the “+” or “-” switch until the
desired speed is displayed.
1 Increase set vehicle speed
2 Decrease set vehicle speed
The set vehicle speed will increase
or decrease as follows:
Short press adjustment: By 1 km/h (0.6
mph) or 1 mph (1.6 km/h) each time the
switch is pressed
Long press adjustment: Increases con-
tinuously while the switch is pressed
and held
■Increasing the set vehicle
speed using the accelerator
pedal
1 Depress the accelerator pedal
to accelerate the vehicle to the
desired vehicle speed.
2 Press the “+” switch.
Adjusting the set vehicle
speed
Canceling/resuming control

318
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
1Press the cancel switch or driv-
ing assist switch to cancel con-
trol.
Control will also be canceled if the brake pedal is depressed.
2 Press the “RES” switch to
resume control.
■Automatic cancelation of the cruise
control
In the following situations, the cruise control will be canceled automatically:
●When the vehicle speed drops approximately 16 km/h (10 mph) or
more below the set vehicle speed
●When the vehicle speed drops below
approximately 30 km/h (20 mph)
●When the brake control or output
restriction control of a driving support system operates (For example: PCS, drive-start control)
●When the parking brake has been operated
●Situations in which some or all of the functions of the system cannot oper-
ate: P. 2 8 1
*: If equipped
■Meter display
Set vehicle speed
Speed limiter indicator
Speed limiter*
A desired maximum speed can
be set using the speed limiter
switch. The speed limiter pre-
vents the vehicle speed from
exceeding the set speed.
WARNING
■Situations in which speed limiter should not be used
●Situations in which the sensors may
not operate properly: P.279
●When it is necessary to disable the
system: P.275
System Components

319
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
■Switches
Driving assist switch
Driving assist mode select
switch
Cancel switch
“-” switch
“+” switch/“RES” switch
1 Press the driving assist mode
select switch to select the speed
limiter.
The speed limiter indicator will illumi- nate in white.
2 Accelerate or decelerate to the
desired vehicle speed, and
press the driving assist switch to
set the maximum vehicle speed.
The speed limiter indicator will change
from illuminated in white to green.
The set vehicle speed will be displayed on the multi-information display in
green.If the vehicle speed is set while driving at below approximately 30 km/h (20 mph), the set vehicle speed will be
set to approximately 30 km/h (20 mph).
Press the cancel switch or driving assist switch to cancel control.
The system does not start when the shift position is R.
The system does not start when the driving assist switch is pressed continu-ously.
To change the set vehicle speed,
press the “+” or “-” switch until the
desired speed is displayed.
1 Increase set vehicle speed
Setting the maximum vehi-
cle speed
Adjusting the set vehicle
speed

320
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
2Decrease set vehicle speed
Short press adjustment: Press the
switch
Long press adjustment: Press and hold
the switch until the desired set vehicle
speed is reached.
The set vehicle speed will increase or
decrease as follows:
Short press adjustment: By 1 km/h (0.6
mph) or 1 mph (1.6 km/h) each time the
switch is pressed
Long press adjustment: Increases or
decreases in 5 km/h (3.1 mph) or 5
mph (8 km/h) increments continuously
while the switch is pressed and held
The set vehicle speed adjustment
increment can be changed through a
customize setting.
1 Press the cancel switch or driv-
ing assist switch to cancel con-
trol.
2 Press the “RES” switch to
resume control.
When control is canceled, the speed
limiter indicator will change from illumi- nated in green to white.
■Exceeding the set speed
In the following situations, if the vehicle
speed exceeds the set vehicle speed, the displayed set vehicle speed will flash:
●When the accelerator pedal is deeply depressed
●When driving down a slope
■Automatic cancellation of the speed limiter
●Situations in which some or all of the functions of the system cannot oper-
ate: P. 2 8 1
■Changes in brake operation sound and pedal response
 P. 4 0 8
When RSA function is enabled and
the speed limiter is operating, if a
speed limit sign is detected, the
detected speed limit will be dis-
played with an up/down arrow. The
set vehicle speed can be
increased/reduced to the detected
speed limit by pressing and holding
the “+” or “-” switch.
■When the set veh icle speed is
lower than the detected speed
limit
Press and hold the “+” switch.
Canceling/resuming control
Speed limiter with Road
Sign Assist

321
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
■When the set vehicle speed is
higher than the detected
speed limit
Press and hold the “-” switch.
■The speed limiter with road sign
assist may not operate properly when
As the speed limiter with road sign
assist may not operate properly in situa- tions where the RSA may not operate or cannot detect signs correctly ( P.304),
when using this function, make sure to confirm the actual speed limit.
In the following situations, the set speed
may not change to the detected speed limit by pressing and holding the “+” switch or “-” switch:
●When the detected speed limit is the same as the set speed
●When the detected speed limit is out-side of the speed range which the
speed limiter system can operate
Emergency Driving Stop
System
The emergency driving stop
system is a system which
automatically decelerates and
stops the vehicle within its
lane if the driver becomes
unable to continue driving the
vehicle, such as if they have
suffered a medical emergency,
etc.
During LTA (Lane Tracing
Assist) control, if the system
does not detect driving opera-
tions, such as if the driver is
not holding the steering wheel,
and determines the driver is
not responsive, the vehicle will
be decelerated and stopped
within its current lane to help
avoid a collision or reduce the
impact of a collision.
WARNING
■For safe use
●Driving safely is solely the responsi-
bility of the driver. Pay careful atten- tion to the surrounding conditions in order to ensure safe driving. The
emergency driving stop system is designed to provide support in an emergency where it is difficult for
the driver to continue driving, such as if they have had a medical emer-gency. It is not designed to support
driving while drowsy or in poor physical health, or inattentive driv-ing.

322
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Operation of this system is sepa-
rated into 4 control states. Through
control state “warning phase 1” and
“warning phase 2”, the system
determines if the driver is aware
and responsive while outputting a
warning and controlling the vehicle
speed. If the system determines the
driver is not responsive, it will oper-
ate in control state “deceleration
stop phase” and “stop hold phase”
and decelerate and stop the vehi-
cle. It will then operate continuously
in “stop hold phase”.
■Operating conditions
This system operates when all of the fol- lowing conditions are met:
●When the LTA is on
●When the vehicle speed is approxi-
mately 50 km/h (30 mph) or more
■Operation cancelation conditions
In the following situations, system oper- ation will be canceled:
●When LTA control has been canceled
(the LTA switch has been pressed, etc.)
●When the dynamic radar cruise con-trol has been canceled
●When driver operations are detected (the steering wheel is held, the brake pedal, accelerator pedal, parking
brake, hazard light switch, or turn sig- nal lever is operated)
●When the driving assist switch is pressed while in the stop and hold phase
●When the power switch has been turned from ON to OFF
●Situations in which some or all of the
WARNING
●Although the emergency driving stop system is designed to deceler-
ate the vehicle within its lane to help avoid or help reduce the impact of a collision if the system
determines that it is difficult for the driver to continue driving, its effec-tiveness may change according to
various conditions. Therefore, it may not always be able to achieve the same level of performance.
Also, if the operating conditions are not met, this function will not oper-ate.
●After the emergency driving stop system operates, if driving
becomes possible again, immedi- ately begin driving again or, if nec-essary, park the vehicle on the
shoulder of the road and set a warning reflector and flare to warn other drivers of your stopped vehi-
cle.
●After this system operates, passen-
gers should attend to the driver as necessary and take appropriate hazard prevention measures, such
as moving to a place where safety can be ensured, such as the shoul-der of the road or behind a guard-
rail.
●T h i s s y s t e m d e t e c t s t h e c o n d i t i o n o f
the driver through the operation of the steering wheel. This system may operate if the driver is aware
but intentionally and continuously does not operate the vehicle. Also, the system may not operate if it
cannot determine that the driver is not responsive, such as if they are leaning on the steering wheel.
●Vehicles with a driver monitor cam-era: Situations in which the driver
monitor may not operate properly:  P. 2 8 1
Summary of the system

323
5
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
Driving
functions of the system cannot oper-
ate: P. 2 8 1
■LTA control when operation is can- celed
When emergency driving stop system
operation is canceled, LTA control may also be canceled.
If driving operations are not
detected after the hands off steer-
ing wheel warning operates, a
buzzer will sound intermittently and
a message will be displayed to
warn the driver, and the system will
judge if the driver is responsive or
not. If driving operations, such as
holding the steering wheel, are not
performed within a certain amount
of time, the system will enter warn-
ing phase 2.
Vehicles with a driver monitor cam-
era: Depending on the type of
detection of the driver’s unrespon-
siveness, the system may skip
warning phase 1 and start the con-
trol of warning phase 2.
After entering warning phase 2, a
buzzer will sound in short intervals
and a message will be displayed to
warn the driver, and the vehicle will
slowly decelerate. If driving opera-
tions, such as holding the steering
wheel, are not performed within a
certain amount of time, the system
will determine that the driver is not
responsive and enter the decelera-
tion stop phase.
The audio system will be muted until
the driver becomes responsive.
When the vehicle is decelerating, the
brake lights may illuminate, depending
on the road conditions, etc.
After the vehicle has decelerated a cer-
tain amount, the emergency flashers
(hazard lights) will flash.
After the driver is judged as being
not responsive, a buzzer will sound
continuously and a message will be
displayed to warn the driver, and
the vehicle will slowly decelerate
and stop. While the vehicle is
decelerating, the emergency flash-
ers (hazard lights) will flash to warn
other drivers of the emergency.
After the vehicle is stopped, the
parking brake will be applied auto-
matically. After entering the stop
and hold phase, the buzzer will
continue sounding continuously, the
emergency flashers (hazard lights)
will flash to warn other drivers of
the emergency, and the doors will
unlock.
Warning phase 1
Warning phase 2
Deceleration stop phase
Stop hold phase

324
Owners Manual_Europe_M42D76_en
5-4. Using the driving support systems
*: If equipped
Meter control switches
Turning the Blind Spot Monitor on/off.
Outside rear view mirror indica-
tors
When a vehicle is detected in a blind
spot of the outside rear view mirrors or
approaching rapidly from behind into a
blind spot, the outside rear view mirror
indicator on the detected side will illumi-
nate. If the turn signal lever is operated
toward the detected side, the outside
rear view mirror indicator flashes.
Driving assist information indica-
tor
Illuminates when the Blind Spot Monitor
is turned off. At this time, “Blind Spot
Monitor OFF” will be displayed on the
multi-information display.
■Outside rear view mirror indicator
visibility
In strong sunlight, the outside rear view mirror indicator may be difficult to see.
■Customization
Some functions can be customized. ( P.570)
■Certification
 P. 6 4 3
BSM (Blind Spot Moni-
tor)*
The Blind Spot Monitor is a
system that uses rear side
radar sensors installed on the
inner side of the rear bumper
on the left and right side to
assist the driver in confirming
safety when changing lanes.
WARNING
■Cautions regarding the use of
the system
●The driver is solely responsible for safe driving. Always drive safely,
taking care to observe your sur- roundings.
●The Blind Spot Monitor is a supple-mentary function which alerts the driver that a vehicle is in a blind
spot of the outside rear view mirrors or is approaching rapidly from
behind into a blind spot. Do not overly rely on the Blind Spot Moni-tor. As the function cannot judge if it
is safe to change lanes, over reli- ance could lead to an accident resulting in death or serious injury.
As the system may not function cor- rectly under certain conditions, the
driver’s own visual confirmation of safety is necessary.
System components