2022 MAZDA MODEL MX-30 EV start

The driver’s seat belt is unfastened and the driver’s door is opened.
NOTE
When the AUTO P (parking lock) function operates, only the shift position changes
to the P position automatically. The shift po sition indication in the instrument cluster
will di ffer from the selector lever position because the selector lever position does
not change. Check the shift position indication in the instrument cluster and shift the
selector lever to the P position.
Neutral hold mode (autom atic car wash mode)
When in neutral hold mode (automatic car wash mode), a condition is maintained
for about 25 minutes in which the power switch is switched to ACC, the shift
position is in the N position, and the parking brake is released.
Use this mode when it is necessary to release the parking brake and change the shift
position to the N position, such as in an automatic car wash that moves the vehicle
by placing the front and rear tires on one side of the vehicle on a belt conveyor.
Operating neutral hold mode (automatic car wash mode)
Perform any of the following operations when the selector lever is in the N position
with the power switch switched ON (EV system on).
Operation method 1
1. Press the power switch with the brake pedal depressed to start the EV system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn o ff the AUTOHOLD.
5. Press the Electric Parking Brake (EPB) switch continuously for 2 seconds or longer (until a sound is activated).
6. Release the EPB switch and press the pow er switch within 5 seconds after the
sound was activated.
Operation method 2
1. Press the power switch with the brake pedal depressed to start the EV system.
2. Release the parking brake.
3. Shift the selector lever to the N position.
4. Turn o ff the AUTOHOLD.
5. Press the power switch with the EPB switch pressed and held while the brake
pedal is not depressed.
NOTE
When the selector lever is shifted from the N position to the D or R position while
neutral hold mode (automatic car wash mode) is operating , a message is displayed
on the multi-information display and the warning beep is activated.
Canceling neutral hold mode (automatic car wash mode)
If any of the following operations is performed, neutral hold mode (automatic car
wash mode) is canceled.
When Driving
Selector Lever Position Functions
4-29
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Shift-Lock System
▼Shift-Lock System
The shift-lock system prevents shifting
out of P unless the brake pedal is
depressed.

1. Depress and hold the brake pedal.
2. Press the power switch to start the
EV system.
3. Shift the selector lever while pressing the selector lever button.
NOTE
When the power switch is switched
OFF or to ACC, or ON (EV systemo ff), the selector lever cannot be
moved from the P position.
When canceling the shift-lock
system, switch the power switch ON
(EV system on) and shift the selector
lever with the brake pedal
depressed.
If the selector lever cannot be shifted
from the P position, the lead-acid
battery could be depleted.
Refer to Jump-Starting on page
7-12.
Driving Tips
▼ Driving Tips
When starting to drive the vehicle or
reversing the vehicle
WARNING
Do not shift the selector lever with the
accelerator pedal depressed when the
selector lever is in the P or N position:
Otherwise, the vehicle will suddenly
accelerate which could lead to an
accident. Shift the selector lever with
the brake pedal depressed.
1. Shift the selector lever with the
brake pedal depressed.
Forward: DReverse: R
2. Check the shift position indication in the instrument cluster.
3. Release the parking brake.
4. Gradually release the brake pedal and depress the accelerator pedal
to start driving the vehicle.
CAUTION
When visually checking at the rear of
the vehicle while reversing the vehicle,
your body twists around to the rear. Be
careful and make sure that the brake
pedal can be firmly depressed.
NOTE
When the shift position is in the R
position, the beep is activated to
notify the driver that the shift
position is in the R position.
When Driving
Selector Lever Position Functions
4-32
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

There is the possibility of forgetting
that the selector lever is shifted to
the R position when only reversing
the vehicle a little. After reversing the
vehicle, immediately shift the
selector lever to the N or P position,
and before starting to drive the
vehicle again, check the shift
position indication in the instrument
cluster.
When driving
WARNING
Do not shift the selector lever to the N
position while driving:
Decelerat ion using the regenerat ive
braking is not possible which could
result in an accident.
Normal driving
Shift the selector lever to the D
position to drive the vehicle.
Acceleration/deceleration is
performed using the accelerator and
brake pedals.
Driving on steep upslopes
Slowly depress the accelerator pedal to
adjust the vehicle speed.
Driving on downslopes
On long or steep downslopes, increase
the amount deceleration using the
regenerative braking in regenerative
braking level change mode.
CAUTION
 On long downslopes, operate the
regenerative braking and the foot
brake together. Frequent
deceleration by depressing the brake
pedal could cause the disc brakes to
overheat and become ine ffective.
 If only strong regenerative braking is
used continuously, it could stop
working temporarily.
Regeneration braking is less e ffective
the closer the high voltage battery is
to a full charge, and regeneration
braking will not work when the high
voltage battery is fully charged.
Stopping the vehicles
1. After completely stopping the vehicle, continue to depress the
brake pedal firmly.
2. If necessary, apply the parking brake with the brake pedal
depressed.
3. If the vehicle is going to be parked for a long time, shift the selector
lever to the P position with the
brake pedal depressed.
WARNING
Do not depress the accelerator pedal
unnecessarily while the vehicle is
stopped:
If the accelerator pedal is mistakenly
depressed when the selector lever is in
a position other than the P or N
position, the vehicle could suddenly
accelerate resulting in an accident.
After stopping the vehicle, check the
shift position indication in the
instrument cluster before
re-accelerating:
If the vehicle were to move in the
unintended direction, it could lead to
an accident.
CAUTION
Do not depress the accelerator pedal
and the brake pedal at the same time,
or rev the motor with the selector lever
in the forward drive position while the
vehicle is stopped on an upslope. The
motor could overheat and lead to
damage.
When Driving
Selector Lever Position Functions
4-33
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

*2 During the daytime, the daytime running lights turn on automatically. During the nighttime, theheadlights, parking lights, taillights, and the license plate lights turn on automatically.
*3 During the daytime, the daytime running lights, parking lights, taillights, and the license plate lights
turn on automatically. During the nighttime, the headlights, parking lights, taillights, and the license
plate lights turn on automatically.
*4 When the light switch is switched to the OFF posit ion while the vehicle is stopped, all of the lights
that are turned on turn o ff. When the light switch is switched from a position other than
to the
position while the vehicle is stopped,the daytime running lights or the headlights turn o ff.
When starting to drive the vehicle, the lights that are turned o ff turn on again.
Auto-light control
When the power switch is switched ON, the light sensor detects the brightness of
the surrounding area and the headlights and the exterior lights turn on/off
automatically according to the surrounding brightness. When the power switch is
switched OFF, the headlights an d the exterior lights turn off automatically.
CAUTION
 Do not shade the light sensor by adhering a sticker or a label on the windshield.
Otherwise the light sensor will not operate correctly.
 The light sensor also works as a rain sensor for the auto-wiper control. If the wiper
lever is in the AUTO position with the power switch switched ON, the wipers may
operate automatically. Be careful not to pinch your hand or fingers. Otherwise, it
could cause injury or damage to the windshield wipers. When cleaning the
windshield (especially when removing snow or ice with the power switch switched
ON (EV system on)), make sure that the wiper switch is turned o ff. If the wipers
are operated, it could cause a problem wi th the windshield wiper or damage the
wiper blade.
NOTE
The headlights and other exte rior lights may not turn off immediately even if the
surrounding area becomes well-lit because the light sensor determines that it is
night time if the surrounding area is cont inuously dark for several minutes such as
inside long tunnels, traffi c jams inside tunnels, or in indoor parking lots.
The sensitivity of the auto-light control may be changed.
When Driving
Switches and Controls
4-36
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

If the auto-wiper lever is left in the
AUTO position, the wipers could
operate automatically from the effect
of strong light sources,
electromagnetic waves, or infrared
light because the rain sensor uses an
optical sensor. It is recommended
that the auto-wiper lever be
switched to the OFF position other
than when driving the vehicle under
rainy conditions.
If the headlight switch and the
windshield wiper switch are in
AUTO, and the wipers are operated
at low or high speed by the auto
wiper control for several seconds,
bad weather conditions are
determined and the headlights may
be turned on.
The auto-wiper control functions can
be turned o ff.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼ Windshield Washer
Pull the wiper lever toward you to
spray washer
fluid and operate the
windshield wipers several times. The
washer fluid is sprayed only while the
windshield wipers move out of their
stowed positions to the point where
they start reversing back.

1. OFF
2. Washer
NOTE
If the windshield washer is turned on
when the windshield wipers are not
operating, the windshield wipers
operate a few times.
If you pull the wiper lever while the
windshield wipers are reversing back
to their stowed positions, the next
time the washer fluid is sprayed is
during the next cycle.
If the washer does not work, inspect
the fluid level (page 6-13). If the fluid
level is normal, consult an Authorized
Mazda Dealer.
When Driving
Switches and Controls
4-43
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

turns off when releasing the parking
brake.
1. Indicator light
WARNING
Do not drive the vehicle with the
parking brake applied:
If the vehicle is driven with the parking
brake applied, the brake parts may
generate heat and the brake system
may not operate, leading to an
accident.
Before driving the vehicle, release the
parking brake and make sure that the
EPB indicator light in the instrument
cluster turns o ff.
Apply the parking brake when leaving
the vehicle:
Not applying the parking brake when
parking the vehicle is dangerous as the
vehicle may move unexpectedly and
result in an accident. Before leaving the
vehicle, apply the parking brake and
make sure that the EPB indicator light
in the instrument cluster turns on.
NOTE
The parking brake cannot be applied
or released while the vehicle battery
is dead.
Refer to Jump-Starting on page
7-12.
When the power switch is switched
OFF while the charging system
warning light in the instrument
cluster turns on, the parking brake
cannot be applied. Before switching
the power switch OFF, apply the
parking brake manually.
The sound of the parking brake being
applied or released can be heard,
however, this does not indicate a
problem.
If the EPB is no t used for long
periods, an automatic inspection of
the system is performed while the
vehicle is parked. An operation
sound can be heard, however, this
does not indicate a problem.
When applying the parking brake
and switching the power switch OFF,
an operation sound can be heard,
however, this does not indicate a
problem.
The brake pedal may move while
applying or releasing the parking
brake, however, this does not
indicate a problem.
If there is a problem with the brake
system (foot brake) while driving the
vehicle, continually pulling up the
EPB switch will apply the brakes and
decelerate or stop the vehicle. The
parking brake on-reminder sound is
activated while the brake is applied.
In addition, when releasing the
switch, the brake is released and the
sound stops.
If the parking brake is applied with
the power switch switched OFF or in
ACC, the EPB indicator light in the
instrument cluster and the indicator
light in the EPB switch may flash for
15 seconds.
When Driving
Brake
4-53
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Releasing the parking brake
automatically
If the accelerator pedal is depressed
with the parking brake applied and all
of the following conditions met, the
parking brake is released automatically.
When the parking brake is released,
the EPB indicator light in the
instrument cluster and the EPB switch
indicator light turn off.
The power switch is switched ON
(EV system on).
The driver's door is closed.The driver's seat belt is fastened.The selector lever is in the D or R
position.
NOTE
If something such as the driver’s foot
contacts the accelerator pedal with the
power switch switched ON (EV system
on) and the parking brake applied, the
parking brake might be released
automatically. If you do not intend to
start driving the vehicle immediately,
shift the selector lever to the P or N
position.
Canceling the parking brake
automatic operation
The parking brake automatic operation
can be canceled by doing any of the
following after switching the power
switch from ON to OFF.
Auto operation cancel method 1
1. Switch the power switch ON.
2. Release the parking brake manually.
3. Turn
off the AUTOHOLD.
4. Press the EPB switch continuously for 2 seconds or longer (until a
sound is activated).
5. Release the EPB switch and switch the power switch OFF within 5
seconds after the sound was
activated.
After the auto operation is
canceled, a sound is activated one
time, and the EPB switch indicator
light switches from illumination to
flashing , and then turns o ff after 3
seconds.
Auto operation cancel method 2
1. Switch the power switch ON.
2. Release the parking brake manually.
3. Turn o ff the AUTOHOLD.
4. Switch the power switch OFF with the EPB switch pressed while the
brake pedal is not depressed.
When the auto operation is
canceled, a sound is activated one
time, and the EPB switch indicator
light goes from normal flashing to
faster flashing , and then turns o ff
after 3 seconds.
NOTE
When canceling the parking brake
auto operation and parking the
vehicle, shift the selector lever to the
P position and then use wheel
blocks.
The auto operation may not cancel if
the vehicle is parked on a steep
slope.
When the power switch is switched
ON, the parking brake auto operation
is restored.
▼ Warning Light
The warning light turns on when the
system has a malfunction.
Refer to Brake System Warning
Indication/Warning Light on page
7-21.
When Driving
Brake
4-55
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

AUTOHOLD
▼AUTOHOLD
The AUTOHOLD function automatically holds the vehicle stopped, even if you take
your foot
off the brake pedal. This function can be best used while stopped in
traffic
or at a traffic light. The brakes are released when you start driving the vehicle.
WARNING
Do not rely completely on the AUTOHOLD function:
The AUTOHOLD function is only designed to assist the brake operation while the
vehicle is stopped. Neglecting to operate the brakes and relying only on the
AUTOHOLD system is dangerous and could result in an unexpected accident if the
vehicle were to suddenly move. Operate the brakes appropriately in accordance
with the road and surrounding conditions.
Do not release your foot from the brake pedal while the vehicle is stopped on a
steep grade:
Because there is a possibility of the vehicl
e not being held in the stopped position by
the AUTOHOLD function, the vehicle may move unexpectedly and result in an
accident.
Do not use the AUTOHOLD function on slippery roads such as icy or
snow-covered roads, or unpaved roads:
Even if the vehicle is held in the stopped position by the AUTOHOLD function, the
vehicle may move unexpectedly and result in an accident. Operate the accelerator
pedal, brakes, or steering wheel appropriately as necessary.
Immediately depress the brake pedal in the following cases:
Because the AUTOHOLD function is canceled forcibly, the vehicle may move
unexpectedly and result in an accident.
 “Depress Brake Pedal. Brake Hold Disabled” is displayed in the multi-information
display and the warning sound is activated at the same time.
Always apply the parking brake when parking the vehicle:
Not applying the parking brake when parking the vehicle is dangerous as the vehicle
may move unexpectedly and result in an accident. When parking the vehicle, shift
the selector lever to the P position and apply the parking brake.
When Driving
Brake
4-57
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07