2022 MAZDA MODEL MX-30 EV start

NOTE
When on the auto operation screen,
touch the seat indication in the
center of the screen to display the
, , , , and icons.
When swiping the , , , ,
or
to the left, the icon two icons
to the left can be selected. When
swiping to the right, the icon two
icons to the right can be selected.
Basic Climate Control
System Operation
▼ Air Conditioner Basic Operation
Operate the air conditioner (cooling,
defrosting functions) with the EV
system started. The air conditioner can
be used while charging when the
power switch is switched ON. In
addition, Cabin preconditioning can
also be used when the power switch is
switched OFF.
NOTE
When the charging is completed with
the power switch switched ON, the air
conditioner (cooling , heating ,
defrosting functions) stops
automatically.
1. Press the AUTO switch. Selection of
the air flow mode, air intake
selector and amount of air flow will
be automatically controlled.
2. Operate the temperature setting
switch/
(red) or (blue) to
set the desired temperature.
NOTE
The recommended set
temperature is 22 °C (72 °F).
Setting the temperature to
maximum hot or cold will not
provide the desired temperature
at a faster rate.
The power consumption of the
air conditioner changes
depending on the set
temperature and the ambient
temperature. If the set
temperature is too low or high,
the remaining distance to full
discharge shortens.
3. To turn o ff the system, press the
climate control power switch.
Interior Features
Climate Control System
5-7
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

The high voltage battery or the
lead-acid battery charge is low
 The doors/liftgate are open
 The power switch is switched to a
position other than OFF
 There is a problem with the vehicle
 If the operation conditions are not
met 30 minutes before the departure
time set by the climate control timer,
the climate control timer will not
operate.
 If any of the follo wing conditions is
met, the climate control system will
not operate e ffectively and the cabin
temperature may not reach the set
temperature:
 Your power consumption is high
 Extremely high or low
temperatures
 The climate control system stops at
the departure time. The cabin
temperature may not reach the set
temperature if you get in the vehicle
earlier or later than the set departure
time.
 If you operate the cabin
preconditioning while charging the
vehicle, it could take more time to
charge the high voltage battery.
 During the cabin preconditioning
operation, the cooling fan, the
compressor, and the cabin fans
operate, but this does not indicate a
problem.
 The climate control system functions
you can use di ffer depending on the
power switch position.
Function Power switch position
OFF ACC ON
(EV
sys-
tem
o ff ) ON
(EV
sys-
tem
on)
Air circulation — — X X
Function Power switch position
OFF ACC ON
(EV
sys-
tem o ff ) ON
(EV
sys-
tem on)
Cooling/heating — — X
*1X
Climate Control
Timer X ———
Remote climate
control X ———
X
: Available
—: Not available
*1 The cooling/heating function can be used only while charging.
NOTE
The recommended set temperature
is 22 °C (72 °F). If you set an
extremely high or low temperature,
power consumption will increase
and the charging time will take
longer.
If you operate the cabin
preconditioning while the charging
connector is connected, you can
reduce the electric power
consumption of the high voltage
battery. Cabin preconditioning can
be operated even without
connecting the charging connector,
however, the electrical power of the
high voltage battery will decrease.
If quick charge is started during cabin
preconditioning , the cabin
preconditioning is stopped.
While the cabin preconditioning is
operating , the indicator light for the
climate control power switch turns
on.
Interior Features
Climate Control System
5-11
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

7If Trouble Arises
Helpful information on what to do if a problem arises with the
vehicle.
Parking in an Emergency............ 7-2 Parking in an Emergency......... 7-2
Flat Tire................................... 7-3 Tool Storage.......................... 7-3
Emergency Flat Tire Repair
Kit........................................ 7-4
Changing a Flat Tire..............7-10
Troubleshooting for Charging ..........
............................................ 7-11 What to do when charging is not
possible.............................. 7-11
Depleted Lead-acid Battery...... 7-12 Jump-Starting...................... 7-12
Fully Discharged High Voltage
Battery...................................7-16 Fully Discharged High Voltage
Battery................................ 7-16
Emergency Starting................. 7-17 Push-Starting....................... 7-17
Emergency Towing.................. 7-18 Towing Description.............. 7-18
Tiedown Hooks*.................. 7-19
Warning/Indicator Lights and
Warning Sounds..................... 7-21 If a Warning Light Turns On or
Flashes................................ 7-21
Message Indicated on Multi-
information Display............. 7-33
Warning Sound is
Activated.............................7-37
When Liftgate Cannot be
Opened................................. 7-42 When Liftgate Cannot be
Opened.............................. 7-42
Active Driving Display Does Not
Operate................................. 7-43 If the Active Driving Display Does
Not Operate........................ 7-43
Windshield Wipers Operate at High
Speed.................................... 7-44 Windshield Wipers Operate at
High Speed......................... 7-44
*Some models.7-1
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

12.Adhere the speed restriction stickerto an area where it can be viewed
easily by the driver.

13.Adhere the repaired tire sticker tothe wheel of the flat tire.

WARNING
Do not adhere the speed
restriction sticker to the padded
area on the steering wheel:
Adhering the speed restriction
sticker to the padded area on the
steering wheel is dangerous
because the air bag may not
operate (deploy) normally resulting
in serious injury. In addition, do not
adhere the sticker to areas where
warning lights or the speedometer
cannot be viewed.
14.When the tire in flates to the
specified tire in flation pressure, turn
the air compressor switch o ff, turn
the sleeve of the injection hose to
the left, and pull it out of the tire
valve.
15.Remove the air compressor hose from the injection valve of the
bottle. After that, install the
injection hose to the injection valve
of the bottle to prevent leakage of
any remaining sealant.

CAUTION
The remaining sealant in the hose
may spray out when the hose is
removed. Remove the hose
carefully because you may not be
able to remove the sealant
contacting clothing or other
objects.
16.Install the tire valve cap.
17.Put the emergency flat tire repair kit
into the trunk.
18.Start driving immediately to spread the sealant in the tire.
CAUTION
Carefully drive the vehicle at a
speed of 80 km/h (50 mph) or less.
If the vehicle is driven at a speed of
80 km/h (50 mph) or more, the
vehicle may vibrate.
If Trouble Arises
Flat Tire
7-8
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Jump-Starting
▼Jump-Starting
The lead-acid battery might be depleted
if the following conditions occur.
The EV system does not start.The selector lever cannot be shifted to a position other than P.The horn sound is weak or it does not sound.The brightness of the lights is extremely low.
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If
you feel unsure about jump-starting, we strongly recommend that you have a
competent service technician do the work.
Using commercially available booster cables, connect the lead-acid battery of the
booster vehicle’s battery to the lead-acid battery of your vehicle and start the EV
system.
WARNING
Follow These Precautions Carefully:
To ensure safe and correct handling of the lead-acid battery, read the following
precautions carefully before using the lead-acid battery or inspecting it.
Keep flames and sparks away from open lead-acid battery cells and do not
allow metal tools to contact the positive (+) or negative (–) terminal of the
lead-acid battery when working near a lead-acid battery. Do not allow the
positive (+) terminal to contact the vehicle body:
Flames and sparks near open lead-acid battery cells are dangerous. Hydrogen gas,
produced during normal lead-acid battery operation, could ignite and cause the
lead-acid battery to explode. An exploding lead-acid battery can cause serious burns
and injuries. Keep all flames including cigarettes and sparks away from open
lead-acid battery cells.
If Trouble Arises
Depleted Lead-acid Battery
7-12
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Keep all flames and sparks away from open
lead-acid battery cells because
hydrogen gas is produced from open le ad-acid battery cells while charging the
lead-acid battery or adding lead-acid battery fluid:
Flames and sparks near open lead-acid ba ttery cells are dangerous. Hydrogen gas,
produced during normal lead-acid battery operation, could ignite and cause the
lead-acid battery to explode. An explodin g lead-acid battery can cause serious burns
and injuries. Keep all fl ames including cigarettes and sparks away from open
lead-acid battery cells.
Do not jump-start a frozen lead-acid battery or one with a low fluid level:
Jump-starting a frozen lead-acid battery or one with a low fluid level is dangerous. It
may rupture or explode, causing serious injury.
Connect the negative cable to a good ground point away from the lead-acid
battery:
Connecting the end of the second jumper ca ble to the negative (–) terminal of the
depleted lead-acid battery is dangerous.
A spark could cause the gas around the lead-acid battery to explode and injure
someone.
Route the jumper cables away from parts that will be moving:
Connecting a jumper cable near or to moving part (cooling fans) is dangerous. The
cable could get caught when the EV system starts and cause serious injury.
CAUTION
 Connect the booster cables with extreme care.
 Do not jump-start the vehicle with the charging cable connected to your vehicle.
Otherwise, the vehicle could be damaged.
 Do not use your vehicle as a booster vehicle.
NOTE
If your lead-acid battery is depleted, make sure that the booster vehicle's battery is
a lead-acid battery.
1. Move the booster vehicle so that its lead-acid battery is as close as possible to your vehicle's lead-acid battery.
2. Make sure that the power switch is switched OFF.
If Trouble Arises
Depleted Lead-acid Battery
7-13
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Location shown in the figure (do not connect to the negative (-) terminal of
the lead-acid battery)
5. Start the booster vehicle's engine and rev the engine.
6. Start the EV system of your vehicle.
7. Disconnect the booster cables in the reverse order of their connection after the EV system is started.
8. Install the lead-acid battery cover.
9. Have your vehicle inspected by an Author ized Mazda Dealer as soon as possible.
If Trouble Arises
Depleted Lead-acid Battery
7-15
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Push-Starting
▼Push-Starting
Do not push-start your Mazda.
If Trouble Arises
Emergency Starting
7-17
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07