Page 17 of 58

15†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
Cruise Control (CC)*†1 6
Your vehicle’s steering wheel but tons may differ from those in the illustrations . Refer to section 5 in the Owner ’s Manual for more information .
A CRUISE button: Press to turn the Cruise Control on/off
B RES+: Press to resume preset speed or increase Cruising Speed
C SET–: Press to set or decrease Cruising Speed
D CANCEL button: To cancel Cruise Control, do one of the following:
•Press the brake pedal
•Press the CANCEL button
REMINDER: Standard Cruise Control is a par t of Smar t Cruise Control and can be set as the operating mode . To switch from SCC to Standard Cruise Control, press and hold the Driving Assist but ton (SCC must not be activated to change modes) . Repeat to switch back to SCC mode .
•Cruise Control is designed to function above 25 mph
•Cruise Control will not activate until the brake pedal has been depressed at least once after ignition ON or engine star ting
QUICK TIPS
A
B
C
D
Page 18 of 58

16†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSOUL FEATURES & FUNCTIONS GUIDE
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Smart Cruise Control is designed to maintain a predetermined distance from vehicles it detects detected ahead by automatically adjusting the driving speed as needed . When traffic is detected, the vehicle will automatically slow to maintain a set distance behind traffic without depressing the accelerator or brake pedal .
To set/adjust the SCC speed:
•Push the CRUISE button A to turn system ON . The CRUISE indicator will illuminate on the instrument cluster
•Press the SET- button B to set the speed . Press the RES+/SET- button B up/down to increase/decrease the set speed
To set the vehicle distance: Press the Vehicle Distance button C on the steering wheel . The images on the LCD screen D in the Instrument Cluster will change when scrolling through the settings . Each time the button is pressed, the vehicle distance changes E .
To cancel SCC operation: Press the CANCEL button F or press the brake pedal .
To turn SCC OFF: Press the CRUISE button A . The CRUISE indicator on the instrument cluster will turn OFF .
To adjust the sensitivity of SCC: Press the mode button on the Steering Wheel G . With the OK button H, select Drive Assistance, then SCC Response . Then select Fast, Normal or Slow .
Images are for illustrative purposes only and may var y on actual vehicle .
SCC is a supplemental system and is not a substitute for safe driving . It is the responsibilit y of the driver to always check the speed and distance to the vehicle ahead .
Refer to section 5 in the Owner ’s Manual for more information .
The distance set tings are approximations and may var y depending vehicle speed at the time . See owner ’s manual for more information
Smart Cruise Control (SCC)*†4 , 1 6
REMINDERS:
•SCC only operates at speeds above 6 mph
•
SCC is activated when ignition is turned on . Speed will need to be reset when ignition is cycled ON
•
In standard Cruise Control, the driver needs to manually assess the distance from other vehicles as the system will not apply brakes to slow down automatically in order to turn SCC ON/OFF
•
SCC is also canceled when the driver ’s door is opened, gear shift is changed out of D (Drive) and various other conditions . See Owner ’s Manual for other conditions
•
If the SCC system is left on, it can be activated inadver tently . Keep the system off when not in use to avoid set ting a speed which the driver is not aware of
172ft130ft
82ft
106ft
(But tons located on right side on Steering Wheel)
•To change the Cruise Control mode from SCC to standard Cruise Control, press and hold but ton A . Repeat to switch modes again (SCC must not be activated to change modes)
•For the SCC System to operate, the vehicle must be traveling at a minimum speed of 5 mph
•When following a vehicle, the system will automatically adjust your cruise speed based on the vehicle detected in front . It may bring the vehicle to a complete stop if necessar y . If the vehicle stops for more than 3 seconds, the system will disable
QUICK TIPS
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Smar t Cruise ControlVideo
QR CODE
B
D
EF
A
C
G
H
Page 19 of 58

17†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
(Rear Camera)(Rear-Camera Display)
P
R
N
DSHIFTL OCK
RELEASE
Check surroundings for your safety
Rear View Monitor (RVM)†4
The Rear View Monitor is a supplemental system that displays the view behind the vehicle through the audio control unit screen while the vehicle is in Reverse .
The Rear View Monitor activates when the:
1 . Engine Start/Stop button* is in the ON position (green light)
2 .
Gear Shift Lever is in the R (Reverse) position
Rear View Monitor is not a substitute for proper and safe backing-up procedures . Rear View Monitor may not display ever y object behind the vehicle . Always drive safely and use caution when backing up .
For illustrative purposes only . Display may var y .
Refer to section 4 in the Owner ’s Manual for more information .
REMINDERS:
•
While the Rear View Monitor is active the volume will be lowered on all audio modes
•Always drive carefully and use caution when backing up
•
The vehicle speed needs to be slower than 9 mph for the system to operate
•
Through normal use and after inclement weather or washing, the rear camera may become dir t y . Use a clean, microfiber cloth to remove any dir t, debris or spots that may have accumulated on the lens
•
While the Rear View Monitor is active the volume will be lowered on all audio modes
Page 20 of 58

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
18†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSOUL FEATURES & FUNCTIONS GUIDE
Rear Cross-Traffic Collision Avoidance Assist (RCCA)* †4
Rear Cross-Traffic Collision-Avoidance Assist (RCCA), under certain conditions, is designed to warn the driver and may activate the Electronic Stability Control (ESC) and temporarily apply braking if it detects cross traffic approaching the vehicle, when vehicle is in reverse .
When the RCCA rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B . If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision .
RCCA is designed to operate under the following conditions:
•
When the gear shift is in Reverse
•When the vehicle is moving slower than 6 mph
RCCA User Settings:
•To go to the User Settings menu in the Instrument Cluster, press the Mode button C on the Steering Wheel when the vehicle is at a standstill, gear shift in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To turn RCCA on when in User Settings , press the Move (OK) button D up/down, select Driver Assistance, Parking Safety, Rear Cross-Traffic Safety and then press OK D
•
To set the initial warning timing, go to User Settings , press the Move (OK) button D up/down, then go to Driver Assistance, Warning Timing and press the OK button D
•
There are two settings:
– N o r m a l : Maximizes the amount of distance between the vehicles before the initial warning occurs
–
Later: Reduces the amount of distance between the vehicles before the initial warning occurs
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the
audio head unit, then VEHICLE on the screen to enter Vehicle Settings
Refer to section 5 in the Owner ’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Rear Cross-Traffic Collision Avoidance Assist (RCCA) Video
QR CODE
REMINDERS:
•
RCCA can be turned OFF/ON in User Set tings, under Driver Assistance, Parking Safet y
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range, and traveling faster than 3 mph, RCCA will show a warning
•
RCCA is a supplemental system . Do not solely rely on this system and always pay at tention to the road and its conditions
•
Prolonged use of the audio control unit in ACC mode may drain the vehicle’s bat ter y
•
RCCA Warning Volume* can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings on the audio head unit . Go to Driver Assistance, then Warning Volume
•RCCA Warning Volume* can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings on the audio head unit . Go to Driver Assistance, then Warning Volume
QUICK TIPS
A
B
CANCEL
RES
SET+ _
CRUISE
RES
SET+ _<
<+>>-
MODE
+>
>-
MODE
CRUISE
CANCELOK
<
<
OK
(Controls located on right side of Steering Wheel)
C
D
Page 21 of 58

ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ADAS
19†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
Check rear seats
: Alarm OffOK
Rear Occupant Alert (ROA) System with Door Monitoring*
Rear Occupant Alert (ROA) System with Door Monitoring can help alert the driver when a rear passenger may be left in the
vehicle
. The alert will be a message on the Instrument Cluster stating to “Check rear seats” C and a chime will sound .
To turn the system OFF or ON, go to Vehicle Settings*, select Convenience, then Rear Occupant Alert and check/uncheck the box to enable/disable by pressing the OK button on the Steering Wheel .
ROA is not a substitute for one’s at tention . Always check the vehicle’s interior before exiting .
Image is for illustrative purposes only and may not reflect actual feature or operation .
Refer to section 4 in the Owner ’s Manual for more information .
REMINDER: Always be sure to check the passenger areas before leaving the vehicle .
C
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Rear Occupant Aler t (ROA) with Door Monitoring Video
QR CODE
Page 22 of 58

DRIVER'S PANEL
DRIVER’SPANEL
20†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSOUL FEATURES & FUNCTIONS GUIDE
Hill-Start Assist Control (HAC)†6
HAC is designed to prevent the vehicle from rolling backward when accelerating from a stop while on a steep incline . The HAC automatically activates whether the ESC is OFF or ON, but does NOT activate when the ESC has malfunctioned .
Instrument Panel Dimmer
With parking lights / headlights ON, press the button B + or – to adjust display brightness of the instrument panel illumination .
Illumination
Max
MaxMin
HUD
i...
P
# V U U P O M P D B U F E J O Q B O F M U P U I F M F G U P G T U F F S J O H X I F F M
REMINDERS:
•
Door Mood Lamp is a fixed brightness and cannot be adjusted (not to be confused with Advanced Mood Lighting Speaker)
•
If the brightness reaches to the maximum or minimum level, an alarm will sound
REMINDERS:
•
The HAC does not operate when the gear shift is in the P (Park) or the N (Neutral) position
•In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
•HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
Refer to section 5 in the Owner ’s Manual for more information .
Refer to section 5 in the Owner ’s Manual for more information .
Refer to section 4 in the Owner ’s Manual for more information .
HUD
i...
P
OFF
Electronic Stability Control (ESC)*†6
(But ton located in panel to the left of steering wheel)
The ESC system is designed to help stabilize the vehicle during certain cornering maneuvers . It is a good idea to keep the ESC turned ON for daily driving whenever possible .
Press ESC button A to turn ESC OFF/ON .
•HAC provides a t wo-second delay before the vehicle may star t rolling backwards
•When HAC is active (e .g ., accelerating from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator
QUICK TIPS
REMINDERS:
•ESC is ON by default at vehicle star tup . When ignition is cycled, ESC will turn ON again
•
The ESC Indicator Light in the instrument cluster will be lit momentarily whenever the ESC is active
B
A
Page 23 of 58

DRIVER'S PANEL
DRIVER’SPANEL
21†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
Refer to section 5 in the Owner ’s Manual for more information .
ENGINESTART
STOP
# V U U P O M P D B U F E B C P W F ( F B S 4 I J G U
Engine Start/Stop Button*†7
To start the engine:
1 . Depress the brake pedal
2 . Press the ENGINE START/STOP button while gear shift is in P (Park) (light A will not illuminate when starting)
To turn the engine OFF – Press the ENGINE START/STOP button again .
To use the ENGINE START/STOP button, the Smart Key fob must be in the vehicle .
REMINDERS:
•In an emergency situation while the vehicle is in motion, you are able to turn the engine off and to the ACC position by pressing the ENGINE START/STOP but ton for more than 2 seconds or 3 times successively within 3 seconds
•If Smar t Key fob bat ter y is dead, with the lock but ton facing the ENGINE START/STOP but ton, hold the fob up against the ENGINE START/STOP but ton and press
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Engine Star t/Stop But ton Video
QR CODE
Kia Smar t & FoldingKey Fobs VideoTo use electrical accessories:
– ACC position
• When in the OFF position (no light) and without depressing the brake pedal, press the ENGINE START/STOP but ton once (amber light A )
– On position
• When already in the ACC position (amber light A ) and without depressing the brake pedal, press the ENGINE START/STOP but ton again (reddish-orange light A )
• When in the OFF position (no light) and without depressing the brake pedal, press the ENGINE START/STOP but ton t wice (reddish-orange light A )
Keeping the vehicle in ACC or the ON position without engine running may discharge the vehicle’s battery.
QUICK TIPS
A
Page 24 of 58

DRIVER’SPANEL
DRIVER'S PANEL
22†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDSOUL FEATURES & FUNCTIONS GUIDE
A Pull/Press to operate Driver ’s and Front Passenger ’s window Auto Up/Down*
B Press to Unlock/Lock All Doors
C Press to disable Rear Passenger Windows
Power Windows, Window Lock & Central Door Lock
If the inner door handle is pulled once when the door is locked, the door will unlock . If the inner door handle is pulled once more, the door will open .
Refer to section 4 in the Owner ’s Manual for more information .
Rear Door Locks
R
L
R
L
Button configuration may var y depending on vehicle model .
Refer to section 4 in the Owner ’s Manual for more information .
Automatic Door Lock/Unlock
Auto Door Lock/Unlock will engage when the gear shift is moved into or out of the P (Park) position . Refer to the User Settings in the LCD Instrument Cluster modes on how to turn Auto Door Lock/Unlock ON/OFF .
Refer to section 4 in the Owner ’s Manual for more information .
Power / Heated Outside Mirrors*
To adjust mirrors: Toggle switch D left or right to select mirror . Then press arrows E to adjust mirror position .
Mirror heaters automatically turn ON/OFF at the same time the Rear Window Defroster is turned ON/OFF . The Rear Window
Defroster button* is located on climate control system panel .
Refer to section 4 in the Owner ’s Manual for more information .
A
B
C
D
E
REMINDERS:
•When but ton C is pressed, window controls for the Rear Passenger Windows are disabled
•When closing, be mindful of any objects or persons
•While driving with the rear windows down or with the sunroof* in an open or par tially open position, a wind buffeting or pulsation noise may be heard . This noise is a normal occurrence and can be reduced or eliminated by the following:
•If the noise occurs with one or both of the rear windows down, par tially lower both front windows approximately 1 inch
•If the noise occurs with the sunroof open, slightly reduce the size of the sunroof opening
QUICK TIPS
Press but ton again to stop Auto Up/Down function .
QUICK TIP