2022 HYUNDAI PALISADE Owners Manual

5-91
Driving your vehicle
5
When the outside rearview mirror
warning light is not working properly,
the ‘Check side view mirror warning
light’ warning message will appear
on the cluster. Have the vehicle
inspected by an authorized
HYUNDAI dealer.
Blind-Spot Collision Warningdisabled
When the rear bumper around the
rear corner radar or sensor is cov-
ered with foreign material, such as
snow or rain, or installing a trailer or
carrier, it can reduce the detecting
performance and temporarily limit or
disable Blind-Spot Safety system.
If this occurs, the ‘Blind-Spot Safety
system disabled. Radar blocked’
warning message will appear on the
cluster.
Blind-Spot Collision Warning will
operate normally when such foreign
material or trailer, etc. is removed,
and then the engine is restarted. If the function does not operate nor-
mally after it is removed, have the
vehicle inspected by an authorized
HYUNDAI dealer.
OTM070098N
OTM070100N

Even though the warning
message does not appear on
the cluster, Blind-Spot Safety
system may not properly
operate.
Blind-Spot Safety system may
not properly operate in an
area (e.g. open terrain), where
any substance are not detect-
ed right after the engine is
turned on, or when the detect-
ing sensor is blocked with for-
eign material right after the
engine is turned on.
WARNING
Turn off Blind-Spot Safety sys-
tem to install a trailer, carrier,
etc., or remove the trailer, carri-
er, etc. to use Blind-Spot Safety
system.
CAUTION

5-92
Driving your vehicle
Limitations of Blind-SpotCollision Warning
Blind-Spot Collision Warning may not
operate normally, or the function may
operate unexpectedly under the fol-
lowing circumstances:
There is inclement weather, such
as heavy snow, heavy rain, etc.
The rear corner radar is covered with snow, rain, dirt, etc.
The temperature around the rear corner radar is high or low
Driving on a highway (or motor- way) ramp
The road pavement (or the periph- eral ground) abnormally contains
metallic components (i.e. possibly
due to subway construction)
There is a fixed object near the vehicle, such as sound barriers,
guardrails, central dividers, entry
barriers, street lamps, signs, tun-
nels, walls, etc. (including double
structures)
Driving in large areas where there are few vehicles or structures (i.e.
desert, meadow, suburb, etc.) Driving through a narrow road
where trees or grass are over-
grown
Driving on a wet road surface, such as a puddle on the road
The other vehicle drives very close behind your vehicle, or the other
vehicle passes by your vehicle in
close proximity
The speed of the other vehicle is very fast that it passes by your
vehicle in a short time
Your vehicle passes by the other vehicle
Your vehicle changes lane
Your vehicle has started at the same time as the vehicle next to
you and has accelerated
The vehicle in the next lane moves two lanes away from you, or when
the vehicle two lanes away moves
to the next lane from you
A trailer or carrier is installed around the rear corner radar
The bumper around the rear cor- ner radar is covered with objects,
such as a bumper sticker, bumper
guard, bike rack, etc. The bumper around the rear cor-
ner radar is impacted, damaged or
the radar is out of position
Your vehicle height is low or high due to heavy loads, abnormal tire
pressure, etc.

5-93
Driving your vehicle
5
Blind-Spot Collision Warning may not
operate normally, or the function may
operate unexpectedly when the fol-
lowing objects are detected:
A motorcycle or bicycle is detected
A vehicle such as a flat trailer isdetected
A big vehicle such as a bus or truck is detected
A moving obstacle such as a pedestrian, animal, shopping cart
or a baby stroller is detected
A vehicle with low height such as a sports car is detected
For more details on the limita-
tions of the front view camera,
refer to “Forward Collision-
Avoidance Assist (FCA)” and
“Lane Keeping Assist (LKA)
section in chapter 5.
CAUTION
Driving on a curved road
Blind-Spot Collision Warning
may not operate properly
when driving on a curved
road. The function may not
detect the vehicle in the next
lane.
Always pay attention to road
and driving conditions while
driving.
Blind-Spot Collision Warning
may not operate properly
when driving on the curved
road. The function may recog-
nize the vehicle in the same
lane.
Always pay attention to road
and driving conditions while
driving.
WARNING
OJX1079057
OJX1079058

5-94
Driving your vehicle Driving where the road is
merging/dividing
Blind-Spot Collision Warning
may not operate properly
when driving where the road
merges or divides. The func-
tion may not detect the vehi-
cle in the next lane.
Always pay attention to road
and driving conditions while
driving.
Driving on an inclined road
Blind-Spot Collision Warning
may not operate properly
when driving on a slope. The
function may not detect the
vehicle in the next lane or may
incorrectly detect the ground
or structure.
Always pay attention to road
and driving conditions while
driving.Driving where the heights of
the lanes are different
Blind-Spot Collision Warning
may not operate properly
when driving where the
heights of the lanes are differ-
ent. The function may not
detect the vehicle on a road
with different lane heights
(underpass joining section,
grade separated intersec-
tions, etc.).
Always pay attention to road
and driving conditions while
driving.
OJX1079059
OLX2058040
OLX2058039

5-95
Driving your vehicle
5
Information
This device complies with Part 15 of
the FCC rules.
Operation is subject to the following
three conditions:
1. This device may not cause harmfulinterference, and
2. This device must accept any inter- ference received, including interfer-
ence that may cause undesired
operation.
3. Changes or modifications not expressly approved by the party
responsible for compliance could
void the user's authority to operate
the device.
Information
Radio frequency radiation exposure
information:
This equipment complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed
and operated with minimum distance
of 8 in. (20 cm) between the radiator
(antenna) and your body.
This transmitter must not be co-locat-
ed or operating in conjunction with
any other antenna or transmitter.
ii
When you are towing a trailer
or another vehicle, make sure
that you turn off Blind-Spot
Collision Warning.
Blind-Spot Collision Warning
may not operate normally if
interfered by strong electro-
magnetic waves.
Blind-Spot Collision Warning
may not operate for 15 sec-
onds after the vehicle is start-
ed, or the rear corner radars
are initialized.
WARNING

5-96
Driving your vehicle
Blind-Spot Collision-Avoidance
Assist is designed to help detect and
monitor approaching vehicles in the
driver’s blind spot area and warn the
driver of a possible collision with a
warning message and audible warn-
ing.
In addition, if there is a risk of colli-
sion when changing lanes or driving
forward out of a parking space, the
function will help avoid collision by
applying the brake. Blind-Spot Collision-Avoidance
Assist helps detect and inform the
driver that a vehicle is in the blind
spot.Blind-Spot Collision Assist helps
detect and inform the driver that a
vehicle is approaching at high speed
from the blind spot area.
B B
L LI IN N D D- -S S P P O O T T C C O O L LL LI IS S I IO O N N- -A A V VO O I ID D A A N N C CE E A A S SS SI IS S T T ( ( B B C CA A ) ) ( ( I IF F E E Q Q U UI IP P P PE ED D ) )
OJX1079256OJX1079026
The detecting range may vary
depending on the speed of your
vehicle. However, even if there
is a vehicle in the blind spot, the
function may not warn you
when you pass by at high
speeds.
CAUTION
Warning timing may vary
depending on the speed of the
vehicle approaching at high
speed.
CAUTION

5-97
Driving your vehicle
5
When changing lanes by detecting
the lane ahead, if the function judges
that there is a collision risk with an
approaching vehicle in the blind spot,
the function will help avoid collision
by applying the brake.When you are driving forward out of
a parking space, if the function
judges that there is a collision risk
with an approaching vehicle in the
blind spot, the function will help avoid
collision by applying the brake.
Detecting sensor
[1] : Front view camera, [2] : Rear corner radar
Refer to the picture above for the
detailed location of the detecting
sensors.
OJX1079027OJX1079028
OLX2051137L
OLX2051140L

5-98
Driving your vehicle
Blind-Spot Collision Warning
settings
Setting features
Blind-Spot Safety
With the engine on, select or dese-
lect ‘Driver assistance →Blind-spot
safety’ from the Settings menu to set
whether or not to use each function.
OTM070096N
Take the following precautions
to maintain optimal perform-
ance of the detecting sensor:
Never disassemble the rear
corner radar or radar assem-
bly, or apply any impact on it.
If there is impact on the rear
corner radar or near the radar,
even though the warning mes-
sage does not appear on the
cluster, Blind-Spot Safety sys-
tem may not operate properly.
Have the vehicle inspected by
an authorized HYUNDAI deal-
er.
If the rear corner radars have
been replaced or repaired,
have the vehicle inspected by
an authorized HYUNDAI deal-
er.
Use only genuine parts to
repair the rear bumper where
the rear corner radar is locat-
ed.
Do not apply license plate
frame or objects, such as a
bumper sticker, film or a
bumper guard near the rear
corner radar.
The function may not work
properly if the bumper has
been replaced, or the sur-
roundings of the rear corner
radar has been damaged or
paint has been applied.
If a trailer, carrier, etc. is
installed, it may adversely
affect the performance of the
rear corner radar or the func-
tion may not operate.CAUTION
For more details on the precau-
tions of the front view camera,
refer to “Forward Collision-
Avoidance Assist (FCA)” sec-
tion in chapter 5.
CAUTION