2021 NISSAN GT-R Owners Manual

position. Operate the shift lever after
the system check indicator turns off.
. The shift lever cannot be moved if
the shift lever button is pushed
while the system check is being performed, even after the system
check is finished. Release the button
and push it again to operate the
shift lever.
. During winter or at other times when
the temperature is extremely low,
changes in the hydraulic response
characteristics may increase the
amount of time that is required for
the system check. During the system
check, a thudding operating noise
may occur or the engine speed may
decrease, however this does not
indicate that there is a malfunction.
Instruments and controls
2-15

2. NEXT switch3. Vehicle information displayThe drive computer displays the following
information:
.Current fuel consumption
. Vehicle speed
. Cruise control
. Average fuel consumption and speed
. Elapsed time and trip computer
. Distance to empty
. Outside air temperature
. Setting .
Warning
The vehicle information display
can be
changed when the ignition switch is in
the ON position. Push the ENTER switch
to change the display.
NOTE:
. The cruise control display is shown if
cruise control is set. (
“Cruise
control” page 5-35)
. The warning display is not shown if
there are no conditions to warn the
driver.
. Depending on the driving conditions
and other factors, the displayed
values may differ from the actual
values.
. The position of the speedometer
needle and the speed shown in the
vehicle information display may
slightly differ.
CURRENT FUEL CONSUMPTIONThe current fuel economy is displayed
when driving.
DRIVE COMPUTER

OUTSIDE AIR TEMPERATUREThis displays the outside air temperature.
NOTE:
.The outside air temperature may not
be displayed correctly in the follow-
ing cases.
—The outside air temperature is
lower than −22°F (−30°C) or is
higher than 131°F (55°C).
— The vehicle is stopped or is driving
at a low speed (less than approxi-
mately 12 MPH (20 km/h)).
— The temperature in the engine
compartment is high. .
When the outside air temperature is
lower than 37°F (3°C), the low outside
temperature warning will be dis-
played and “ICY” is indicated on the
outside air temperature display.
(
“Alert” page 2-20)Instruments and controls
2-19

SETTING (drive computer)This is used to set the alert, maintenance
and optional settings.
Use the NEXT switch
to select an
item, then confirm with the ENTER switch
to change to the corresponding
setting screen.
To return to the initial setting screen,
push and hold the ENTER switch
for
more than 1 second. NOTE:
.
When the battery terminal is discon-
nected, the set memory will be
erased and the settings return to
the default.
. Setting is not possible in the follow-
ing cases.
—The vehicle is being driven.
— A warning display is active.
— The instrument brightness con-
trol level display is active.
— The cruise control status is dis-
played.
AlertThis function can be used to make
settings for the upshift indicator, “time
to rest” indicator and low outside tem-
perature warning.
Upshift indicator:
For details concerning the upshift indica-
tor, refer to the following section.
(
“Upshift indicator” page 2-10)

to change the time. Push and
hold the switch to increase the number
every 1 hour. A maximum of 6 hours can
be set.
NOTE:
The default setting is OFF.
Low outside temperature warning:
This alert informs the driver when the
outside air temperature is lower than 37°F
(3°C).
On the ICY screen, push the NEXT switch
to turn this warning ON/OFF.
NOTE:
The default setting is ON.
MaintenanceThis function can be used to set the
various maintenance intervals and to
check the engine oil level. The reminders
shown below are used to notify the driver
of the maintenance intervals.
NOTE:
Because these are displayed based on
the mileage driven, they do not indicate
the actual conditions of the vehicle. Use
these functions only as a reference.
Input the maintenance distance using the
following items:
. On each setting screen, push the
Instruments and controls
2-21