2021 MERCEDES-BENZ V-CLASS warning

parallel
tothe side of the battery housing in
th e connection area, as shown. #
Place the positive term inal clamp co ver on pos-
itive term inal 1. #
Fold bo thhandles 3down onto the batter y. #
Push the battery into the seat base until the
negative term inal clamp can be connected. #
Connect the negative term inal clamp tonega-
tive term inal 4. #
Push the battery into the seat base as far as it
will go. Open seat base with /t
tedbattery (e xample:right-
hand front seat) #
Connect vent hose 5tothe battery connec-
tion at theto p, beside negative term inal 4. #
Place holder 7overth e lo wer edge of the
battery housing and theth re aded holes for
scr ews6. #
Screw on holder 7with scr ews6.
The battery is secured toprev ent slipping. Seat base (e
xample:right-hand front seat) #
Insert co ver9 in front of the battery com-
partment down into the seat base and close it.
Catch springs 8of co ver9 should engage
audibl y.
Car ryout thefo llowing workaTer connecting the
batter y: #
Reset the side windo ws (/page 64). #
Reset the outside mir rors ( / page 120). #
Reset the electric sliding doors (/ page 59). #
Reset the EAS Y-PA CK tailgate (/ page 61). T
T
o
o wing or tow
wing or tow-st
-star
arting
ting Ov
Ov
er
ervie
vie w of per
w of per missible to
missible towing met
wing met hods
hods &
W
WARNING
ARNING Risk of accident due tolimited
saf ety-re lated functions during theto wing
process
Saf ety-re lated functions are limited or no lon-
ge rav ailable in thefo llowing situations:
R theve hicle is switched o..
R the brake system or po wer steering system
is malfunctioning.
R the energy supply or the on-board electri-
cal system is malfunctioning.
When your vehicle is towe dawa y,signi/cantly
more e.ort may be requ ired tosteer and brake
th an is normally requi red. #
Use a tow bar. #
Make sure that the steering wheel can
mo vefreely before towing theve hicle
awa y. &
W
WARNI NG
ARNI NGRisk of accident when towing
with steering wheel lock
If th e steering wheel lock is engaged, you will
not be able tosteer theve hicle. #
When towing with a tow rope or tow bar,
alw ays switch on theve hicle. &
W
WARNING
ARNING Risk of accident when towing a
ve hicle which is too heavy
If th eve hicle tobe tow- star ted or towe daway
is heavier than the permissible gross mass of
yo ur vehicle, thefo llowing situations can
occur:
R theto wing eye may become de tach ed.
R theve hicle/trailer combination may
swer veoroverturn. #
Before tow- starting or towing away,
ch eck if theve hicle tobe tow- star ted or
to we dawa yex ceeds the permissible
gr oss mass. Breakdown assistance
245
245

P
P
er
er missible to
missible towing met
wing met hods
hods Bot
Bot
h axles on t
h axles on t he
he
gr
gr ound
ound F
F
r
ront axle r
ont axle r aised
aised R
R
ear axle r
ear axle r aised
aised
Ve hicles with manual
transmission Ye
s, no fur ther than
50 km at 50 km/h No
Yes, if the steering
wheel is /xed in the
cent reposition with a
steering wheel loc k.
Maximum 50 km at
50 km/h
Ve hicles with automatic
transmission Ye
s, no fur ther than
50 km at 50 km/h No
Yes, if the steering
wheel is /xed in the
cent reposition with a
steering wheel loc k.
Maximum 50 km at
50 km/h
Ve hicles with all-wheel
drive (4MATIC) Ye
s, no fur ther than
50 km at 50 km/h No
No%
Ifth e transmission cannot be shiTed toposi-
tion i, ha vetheve hicle transpor ted
( / page 248). A towing vehicle with liTing
equipment is requ ired forve hicle transport. T T
o
o wing awa
wing away t
y the v
he v ehicle wit
ehicle wit h bot
h both axles on t
h axles on t he
he
gr
gr ound
ound #
Obser vethe no tes on permissible towing me th-
ods (/ page 245). #
Make sure that the battery is connected and
ch arge d.
If th e battery is dischar ged, obser vethefo llowing
points:
R The vehicle cann otbe switched on.
R It is not possible torelease or apply the elec-
tric parking brake.
R The transmission cannot be shiTed toposition
i.
V
V ehicles wit
ehicles wit h manual tr
h manual tr ansmission
ansmission #
Switch on the hazard warning lamps
(/ page 108). #
Fitth eto wing eye (/ page 249). #
Secure theto wing device. #
Swit chon theve hicle. #
Deacti vate automatic locking (/ page 55). #
Deactivate Active Brake Assist (/ page 157). #
ShiT the transmission toneutral. #
Release the parking brake (/ page 151).
V
V ehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission
ansmission #
Switch on the hazard warning lamps
(/ page 108). #
Fitth eto wing eye (/ page 249). #
Secure theto wing device. #
Swit chon theve hicle. #
Deacti vate automatic locking (/ page 55). #
Do not activate the HOLD function. #
Deactivate Active Brake Assist (/ page 157). #
Deactivate Active Distance Assist DISTRONIC
(/ page 162). #
ShiT the transmission toi (/ page 142). #
Release the parking brake (/ page 151).
R
R ecov
ecov er
ering a v
ing a v ehicle t
ehicle t hat is s
hat is stucktuck
* NO
NOTE
TEDamage due topulling forc e being
to o high Pulling
away abruptly can damage theve hicles
if th e tractive forc es are too high. Breakdown assistance
247
247

#
Pull away as st raight, slo wlyand
smoo thly as possible. If
th e drive wheels gettrapped on loose or muddy
gr ound, reco verth eve hicle with the utmost care,
especially so if theve hicle is laden. #
Obser vethe no tes on permissible towing me th-
ods (/ page 245). #
Never attem pttoreco ver a vehicle that is
stuck when a trailer is attached. #
If possible, pull theve hicle out backwards
using the trac ksit made before it became
stuc k. T
T
o
o wing t
wing t he v
he vehicle wit
ehicle wit h t
h the axle r
he axle r aised
aised &
W
WARNING
ARNING Risk of accident due to towing
when theve hicle is switched on
When theve hicle is being towe dawa y and is
swit ched on with the front axle raised, ASR can
brake there ar axle wheels in an er ratic man-
ner.
The vehicle can lose directional stability. #
Switch o. theve hicle before towing it
with the front axle raised. *
N NOOTE
TE Damage tothe transmission due to
to wing with an axle raised on vehicles with
4MATIC The transmission can be damaged
bytowing
with the front or rear axle raised. #
Only tow vehicles equipped with 4MATIC
with bo thaxles on thegr ound, or load
th em onto ano ther vehicle for transport. W
W
it
ith t
h t he r
he r ear axle r
ear axle r aised
aised #
Obser vethe no tes on permissible towing me th-
ods (/ page 245). #
Switch on the hazard warning lamps
(/ page 108). #
Deactivate tow- awa y protection (/ page 69). #
Movethe front wheels tothe straight-ahead
position. #
Fixth e steering wheel in the centre position
with a steering wheel loc k.#
Release the parking brake (/ page 151). #
Turn theke yto position ginthe ignition lock
and remo vetheke y from the ignition loc k. #
Take theke y with you when leaving theve hicle.
Do not exceed a towing speed of 50 km/h. Loading t
Loading t
he v
he vehicle f
ehicle f or tr
or transport
ansport *
N NOOTE TE Damage due toincor rect attach-
ment The
vehicle may be damaged when lashing to
ch assis components. #
Only lash theve hicle at the wheels. #
Obser vethe no tes on permissible towing me th-
ods (/ page 245). #
Toload theve hicle onto a trailer or transpor ter,
use the trailer tow hitch or theto wing eye.
Bef
Bef or
ore loading t
e loading t he v
he vehicle
ehicle #
Switch on theve hicle. #
V
Vehicles wit
ehicles wit h manual tr
h manual tr ansmission:
ansmission: shiTthe
transmission toneutral. #
V
Vehicles wit
ehicles wit h aut
h aut omatic tr
omatic tr ansmission:
ansmission: shiTthe
transmission toposition i. #
Release the parking brake (/ page 151). #
Load theve hicle onto the transpor ter.
* N
NO
OTE
TE Damage tothe drive train due to
incor rect positioning of theve hicle #
Do not position theve hicle abo vethe
connection point of the transport vehicle. #
Make sure that the front and rear axles come
to rest on the same transpor tation vehicle.
ATer
ATer loading t
loading t he v
he vehicle
ehicle #
V
Vehicles wit
ehicles wit h manual tr
h manual tr ansmission:
ansmission: engage
/rst or reve rsege ar. #
V Vehicles wit ehicles wit h aut
h aut omatic tr
omatic tr ansmission:
ansmission: shiTthe
transmission toposition j. #
Deactivate tow- awa y protection (/ page 69). 248
248
Breakdown assistance

Before
tow- starting, ensure thefo llowing:
R make sure that the battery is connected and
ch arge d. The vehicle cann otbe switched on
ot herwise and there will be no steering and
braking assistance.
R use a towing bar and attach it tothe front tow-
ing eye (/ page 249) onl y.
R ifth eve hicle does not start aTer a fewsec-
onds, try a jump-starting procedure using the
battery of ano ther vehicle (/ page 240).
T
T o
o w
w -st
-st ar
arting pr
ting pr ocedure
ocedure #
Switch on the hazard warning lamps
(/ page 108). #
If necessar y,allow the engine and theex haust
system tocool down. #
Swit chon theve hicle. #
ShiT to2nd or 3rd gear. #
Release the parking brake. #
Keep the clutch pedal fully depressed when
to w- starting theve hicle. #
Release the clutch pedal slo wly. #
Immediately shiT toneutral if theve hicle
starts. #
Stop in accordance with the tra1c conditions. #
Use the parking brake tosecure theve hicle
against rolling away. #
Remo vetheto wing device. #
Remo vetheto wing eye. #
Switch o. the hazard warning lamps
(/ page 108). Electr
Electr
ical fuses
ical fuses N
No
ot
t es on electr
es on electr ical fuses
ical fuses *
N
NOOTE
TE Electrical fuses #
Obser vethe information in the supple-
ment. You may otherwise failto recog-
nise dangers. The fuse allocation
chart and the information on
th e fuses can be found in the "Fuse allocation
ch art" Supplement. V
V
ehicle t
ehicle t ool kit
ool kit Inf
Inf
or
ormation on t
mation on t he v
he vehicle t
ehicle t ool kit
ool kit The
vehicle tool kit is in there ar st owage compart-
ment.
Apart from some countr y-speci/c variants, vehi-
cles without a spare wheel are not equipped with a
tyre-changing tool.
If yo ur vehicle is equipped with a tyre-change tool
kit, you can /nd it in theve hicle tool kit in there ar
st ow age compartment.
Some tools forch anging a wheel are speci/c to
th eve hicle. For more information on which tyre-
ch ange tool kits are requ ired and appr ovedfo r per-
fo rm ing a wheel change on your vehicle, consult a
qu ali/ed specialist workshop.
Re quired tyre-change tool kits may include thefo l-
lowing, forex ample:
R Jack
R Wheel spanner
R Ratchet ring spanner
% The jack has a maximum weight of 7.5 kg
depending on theve hicle's equipment.
Yo u will /nd the maximum load capacity of the
jack stated on the adhesive label attached to
th e jac k.
The jack is maintenance-free. If there is a mal-
function, please contact a quali/ed specialist
wo rkshop. S S
t
to
o w
w ag
ag e com
e com par
partment in t
tment in t he r
he rear
ear Opening t
Opening t
he stow
he st owag
age com
e com par
partment
tment St
ow age compartment in there ar on theright-
hand side of theve hicle 250
250
Breakdown assis
tance

Inf
Inf
or
ormation on noise or unusual dr
mation on noise or unusual dr iving c
iving char
harac-
ac-
t
t er
er is
istics
tics
While driving, pay attention tovibrations, noises
and unusual driving characteristics, e.g. pulling to
one side. This may indicate damage tothe wheels
or tyres. If you suspect that a tyre is defecti ve,
re duce your speed. Stop theve hicle as soon as
possible tocheck if wheels and tyres ha vebeen
damaged or are no longer functioning proper ly.
Hidden tyre dama gecould also be causing the
unusual driving characteristics. If no signs of dam-
age can be de tected, ha vethe tyres and wheels
ch ecked at a quali/ed specialist workshop. N
No
ot
tes on r
es on r egularl
egularly inspecting wheels and tyr
y inspecting wheels and tyr es
es&
W
WARNING
ARNING Risk of injury due todamaged
tyres
Damaged tyres can cause tyre pressure loss. #
Check the tyres regular lyfor signs of
damage and replace any damaged tyres
immediatel y. Check
the wheels and tyres of your vehicle for
damage regular ly, i.e. at least everytwo weeks, as
we ll as aTer driving o.- road or on rough roads.
Damaged wheels can lead toa loss of tyre pres-
sure.
Look out forth efo llowing types of damage, for
ex ample:
R cuts in the tyres
R punctures in the tyres
R tears in the tyres
R bulges on tyres
R deformation or se vere cor rosion on wheels &
W WARNING
ARNING Risk of aquaplaning due to
insu1cient tyre tread
Insu1cient tyre tread will result in reduced tyre
gr ip.
The risk of aquaplaning is increased on wet
ro ads, especially when the speed of theve hicle
is not adap tedto suit the conditions. #
Thus, you should regular lych eck the
tread dep thand the condition of the
tread across the entire width of all tyres. Minimum tread dep
thfor:
R Summer ty res: 3 mm
R M+S tyres: 4 mm #
For saf etyre asons, replace the tyres
before the legall y-prescribed limit forthe
minimum tread dep thisreached. Conduct
thefo llowing checks regular lyon all
wheels, at least once a month or as requ ired, e.g.
before a long journey or when driving o.- road:
R check the tyre pressure (/ page 253)
R check theva lve caps
Va lves must be pr otected from moisture and
dirt with valve caps speci/cally appro vedby
Mercedes-Benz foryo ur vehicle.
R visually inspect the tread dep thand the tyre
tread across the whole tyre width
The minimum tread dep thfor summer tyres is
3 mm and for winter tyres 4 mm. Inf
Inf
or
ormation on dr
mation on dr iving wit
iving with summer tyr
h summer tyr es
es
At temp eratures below 10 °C summer tyres lose
elasticity and therefore traction and braking po wer.
Change the tyres on your vehicle toM+S tyres.
Using summer tyres at very cold temp eratures
could cause tears toform ,th ereby damaging the
tyres permanentl y.Mercedes-Benz cannot accept
re sponsibility forth is type of damage.
Once you ha ve/tted the summer tyres:
R Check the tyre pressures (/ page 253)
R Restart the tyre pressure monitor
(/ page 258) Inf
Inf
or
ormation on M+S tyr
mation on M+S tyr es
es
At temp eratures below 10 °C, use winter tyres or
all-season tyres that are mar ked with M+S.
Only winter tyres bearing thei snow0ake sym-
bol in addition tothe M+S marking pr ovide the
best possible grip in wintry road conditions.
Only these tyres allow driving saf ety systems such
as ABS and ESP ®
to also function optimal lyin win-
te r. These tyres ha vebeen de veloped speci/cally
fo r driving in sno w.
Use M+S tyres of the same make and tread on all
wheels tomaintain safe handling characteristics.
Obser vethe maximum permissible speed speci/ed
fo rth e M+S tyres you ha ve/tted. 252
252
Wheels and tyres

If
yo u /t M+S tyres that ha vea lo wer maximum
permissible speed than the maximum design
speed of theve hicle, a1x an appropriate warning
sign in the driver's /eld of vision. You can obtain
th is at a quali/ed specialist workshop.
Once you ha ve/tted the winter tyres M+S, take
th efo llowing measures:
R check the tyre pressure (/ page 253)
R restart the tyre pressure monitoring system
(/ page 258) N
No
ot
tes on sno
es on sno w c
w chains
hains &
W
WARNING
ARNING Risk of accident due toincor-
re ctly /tted snow chains
If yo u ha ve/tted snow chains tothe front
wheels, they may drag against theve hicle body
or chassis components. #
Never /t snow chains tothe front wheels. #
Only /t snow chains on there ar wheels
in pairs. Fo
r saf etyre asons, Mercedes-Benz recommends
th at you only use snow chains that ha vebeen
ch ecked and appr oved. You can /nd fur ther infor-
mation on snow chains recommended for
Mercedes-Benz in the wheel and tyre overview at
https://www.mercedes-benz.de. &
W
WARNING
ARNING Risk of accident due tosnow
ch ains breaking
If yo u drive toofast wi thsnow chains, they can
break, injure other persons, and damage the
ve hicle. #
Obser vethe maximum permissible speed
fo r operation with snow chains. *
N
NOOTE
TE Damage tothe wheel trim from /t-
ted snow chains If snow
chains are /tted tosteel wheels, the
wheel trims can be damaged. #
Remo vethe wheel trims of steel wheels
before /tting snow chains. Obser
vethefo llowing no tes when using snow
ch ains:
R Snow chains are only permissible for cer tain
wheel/tyre combinations. You can obtain infor- mation on
them at a quali/ed specialist work-
shop.
R For saf etyre asons, only use snow chains that
ha ve been speci/cally appr oved foryo ur vehi-
cle byMercedes-Benz, or snow chains with the
same quality standard.
R The snow chains must be retightened aTer
driving app roximately 1 km. This is the only
wa yto ensure the snow chains are optimal ly
seated with clearance toadjacent compo-
nents.
R Use snow chains only when thero ad sur face is
comple tely sno w-co vered. Re mo vethe snow
ch ains as soon as possible when you come to
a ro ad that is not sno w-co vered.
R Local regulations may restrict the use of snow
ch ains. Obser vethe applicable regulations
before /tting snow chains.
R If snow chains are /tted, the maximum permis-
sible speed is 50 km/h.
% You can deactivate ESP ®
to pull away
( / page 154). This allo ws the wheels tospin,
achieving an increased driving forc e. T
T
yr
yr e pr
e pr essure
essure N
No
ot
tes on tyr
es on tyr e pr
e pressure
essure Driving with tyre pressure
that is too high or too
low can:
R Shor tenth e service life of the tyres
R Cause increased tyre damage
R Adve rsely a.ect handling characteristics and
th us driving saf ety, forex ample, due toaqua-
planing &
W
WARNING
ARNING Risk of accident due torepea-
te d pressure drop in the tyres
The wheels, valves or tyres could be damaged.
To o low a tyre pressure can lead tothe tyres
bursting. #
Examine the tyres forfo re ign objects. #
Check whe ther the tyre has a puncture
or theva lve has a leak. #
Ifyo u are unable torectify the damage,
contact a quali/ed specialist workshop. Information on
there commended tyre pressure for
th eve hicle's factor y-/tted tyres can be found on Wheels and tyres
253
253

P
P
ar
ar tiall
tiall y laden v
y laden v ehicle
ehicle1
1
F
Full
ull y laden v
y laden v ehicle
ehicle
T
T yr
yr es/disk
es/disk
wheel
wheel Fr
Fr
ont axle R
ont axle R ear axle Fr
ear axle Front axle R
ont axle R ear axle
ear axle
245/45 R 19
XL 102Y 230 kPa (2.3
bar/33 psi) 230 kPa (2.3 bar/33
psi) 260 kPa (2.6
bar/38 psi)270 kPa (2.7
bar/39 psi)
245/45 R 19
XL 102W 260 kPa (2.6
bar/38 psi) 260 kPa (2.6 bar/38
psi) 290 kPa (2.9
bar/42 psi)300 kPa (3.0
bar/44 psi)V V
ehicles wit
ehicles wit h agr
h a gross v
oss v ehicle w
ehicle w eight of
eight of 3,200 kg
3,200 kg
and all-wheel dr
and all-wheel dr iv
ive 4MA
e 4MA TIC
TIC
The following tyre pressure values apply tothefo l-
lowing vehicles:
R with a gross vehicle weight of 3,200 kg
R with a permissible axle load of 1,650 kg on the
re ar axle R
with 4MATIC
R the tyres referred tounder "Wheel and tyre
combinations" (/ page 264)
Ty re pressure forth e spare wheel is 350 kPa
(3.5 bar/51 psi). P
P
ar
ar tiall
tiall y laden v
y laden v ehicle
ehicle1
1
F
Full
ull y laden v
y laden v ehicle
ehicle
T
T yr
yr es/disk
es/disk
wheel
wheel Fr
Fr
ont axle R
ont axle R ear axle Fr
ear axle Front axle R
ont axle R ear axle
ear axle
235/55 R 17
XL 103W/V 270 kPa (2.7
bar/39 psi) 250 kPa (2.5 bar/36
psi) 280 kPa (2.9
bar/41 psi)310 kPa (3.1
bar/45 psi)
245/45 R 19
XL 102Y 230 kPa (2.4
bar/33 psi) 230 kPa (2.3 bar/33
psi) 260 kPa (2.7
bar/38 psi)280 kPa (2.8
bar/41 psi)
245/45 R 19
XL 102W/V 270 kPa (2.7
bar/39 psi) 270 kPa (2.7 bar/39
psi) 290 kPa (2.9
bar/42 psi)310 kPa (3.1
bar/45 psi)T T
yr
yr e pr
e pr essur
essur e monit
e monit or
oring syst
ing syst em
em F
F
unction of t
unction of t he tyr
he tyre pr
e pressur
essur e monit
e monit or
oring syst
ing syst em
em
The system checks the tyre pressure and the tyre
te mp erature of the tyres /t tedtotheve hicle by
means of a tyre pressure sensor.
Ne w tyre pressure sensors, e.g. in winter tyres, are
automatical ly taught-in during the /r stjourney they
are used.
It is the driver's responsibility toset the tyre pres-
sure tothere commended cold tyre pressure suita-
ble forth e operating situation (/ page 253).
No tethat the cor rect tyre pressure forth e cur rent
ope rating situation must /rst be taught-in tothe
tyre pressure monitoring system. If a substantial
loss of pressure occurs, thewa rning thre shold for
th ewa rning message is alignedtotheta ught-in
re fere nce values. Restart the tyre pressure monitor
aTer adjusting tothe cold tyre pressure (/
page 258). The cur rent pressures are sa ved as
new refere nce values. This will ensure that a warn-
ing message will only appear if the tyre pressure
drops signi/cantl y.
The h warning lamp in the inst rument cluster
displa ysa de tected pressure loss or a malfunction
as follo ws:
R ifth eh warning lamp is lit continuousl y,
th e tyre pressure on one or more tyres is sig-
ni/cant lytoo lo w.The tyre pressure moni tor is
not malfunctioning.
R ifth eh warning lamp 0ashes for around a
minute and then remains lit cons tantl y,the tyre
pressure monitor is malfunctioning.
R a message also appears in the inst rument clus-
te r.
1 The tyre pressures forth e partially laden vehicle are not valid forth e Marco Polo with integ rated kitchen. Wheels and tyres
257 257

Syst
Syst
em limits
em limits
The system may be impaired or may not function in
th efo llowing situations:
R the tyre pressure has been set incor rectl y.
R there is a sudden pressure loss caused, for
ex ample, byafo re ign object penetrating the
tyre.
R there is a malfunction caused byano ther radio
signal source.
If th e tyre pressure monitor is malfunctioning, it
may take more than ten minutes forth eh tyre
pressure warning lamp toinform you of the mal-
function. When thefa ult has been recti/ed, the
h warning lamp goes out aTer you ha vedriven
fo r a few minutes.
The tyre pressure values indicated bythe on-board
computer may di.er from those measured at a /ll-
ing station using a pressure gauge.
The tyre pressures shown bythe on-board com-
puter referto those measured at sea le vel.At high
altitudes, the tyre pressure values indicated by a
pressure gauge are higher than those shown bythe
on-board computer. In this case, do not reduce the
tyre pressures.
Chec
Chec king t king t he tyr
he tyr e pr
e pressur
essur e electr
e electr onically
onically
R
R eq
eq uir
uir ements:
ements:
R The vehicle is switched on. #
Press theò button tocall up the list of
menus. #
Press the: or9 button toselect
Service. #
Press thea button. #
Press the: or9 button toselect Tyre
pressure. #
Press thea button.
The display sho ws the current tyre pressure of
each wheel. If
th eve hicle was par kedfo r longer than
20 minu tes, theTyre pressures will be displayed
after a few minutes of driving message appears in
th e displa y.
% Also be sure toobser vethe no tes on tyre
pressure (/ page 253).
R R est est ar
arting t
ting t he tyr
he tyr e pr
e pressur
essur e monit
e monit or
or
R
R eq
equir uir ements:
ements:
R The vehicle is switched on.
R The recommended tyre pressure is cor rectly
set forth ere specti veoperating condition on
each of thefo ur wheels (/ page 254). #
Press theò button tocall up the list of
menus. #
Use the: or9 button toselect
Service. #
Press thea button. #
Use the: or9 button toselect Tyre
pressure. #
Press thea button.
The display sho ws the current tyre pressure of
each wheel or theTyre pressures will be dis-
played after a few minutes of driving mes-
sage. #
Press the: button.
The Use current pressures as new reference
values message is shown in the displa y. #
T
To
o con/rm
con/rm r
rest
est art
art::press thea button.
ATer you ha vedriven for a few minutes, the
system checks whe ther the cur rent tyre pres-
sures are within the speci/ed range. The new
tyre pressures are then sa ved as refere nce val-
ues, monitored and displa yed. #
T
To cancel r
o cancel r est
estart
art: :press the% button.
The tyre pressure values stored at the last
re start will continue tobe monitored. Changing a wheel
Changing a wheel
N
No
ot
tes on selecting,
es on selecting, /tting
/ttingand r
and replacing tyr
eplacing tyr es
es Yo
u can ask for information rega rding permitted
wheel/tyre combinations at a quali/ed specialist
wo rkshop. &
W
WARNING
ARNING Risk of accident due toincor-
re ct wheel and tyre dimensions
If wheels and tyres of the wrong size are /t ted,
th e service brakes or components in the brake 258
258
Wheels and tyres