2021 MERCEDES-BENZ V-CLASS clock

Centr
Centr
e console, low
e console, low er section
er section St
ow age compartment with co ver
1 Cover →
98
2 12 V soc ket →
104
Cigar ette lighter →
104
3 Holder forth e mobile phone
brac ket
4 Media Inter face with two USB
ports or with two USB ports and
one SD card slot 5
Cup holder
6 Ashtr ay →
103
7 Stow age compartment
Switch clock for auxiliary warm-
air heater →
133
Device ins tallation frame for
auxiliary equipment, e.g. a
ta ch og raph At
a glance – Centre console, lo wer section
11 11

inside, only
the door that has been opened is
unloc ked.
R Ifth eve hicle has pr eviously been loc ked with
th eke y,opening a door from the inside will
trigger the anti-theT alarm system. Switch o.
th e alarm (/ page 68). A A
ctiv ctiv ating/deactiv
ating/deactiv ating t
ating the aut
he automatic loc
omatic loc king
king
mec
mec hanism
hanism R
R
eq
equir uir ements:
ements:
R The po wer supply or theve hicle has been
switched on.
R The doors are closed.
When the automatic locking mechanism is activa-
te d and theve hicle is tr avelling at a speed abo ve
15 km/h, theve hicle is loc ked automaticall y. Central locking buttons (vehicles with manually
adjustable front seats) Central locking buttons (vehicles with electrically
adjustable front seats)
R Ifth eve hicle is being tested on a roller dyna-
mome ter or is being tow- star ted or push-star-
te d, there is a risk of being loc ked out when
th e function is activated. #
T To activ
o activ at
ate:
e: press and hold button 2until you
hear a tone. #
T
To deactiv
o deactiv at
ate:
e: press and hold button 1until
yo u hear a tone. U
Unloc
nloc king and loc
king and loc king t
king the dr
he driv
iver's door wit
er's door wit h t
h the
he
eme rg
emerg encykey
ency key %
Tolock theve hicle fully with the emer gency
ke y,press down the locking pins of the doors.
Then lock the driver's door with the emer-
ge ncy key. #
T
To unloc
o unloc k:
k:insert the emer gency key fully in to
th e driver's door lock and turn it anti-cloc k-
wise. #
T
To loc
o loc k:
k:inse rtthe emer gency key fully in tothe
driver's door lock and turn it clockwise.
% Right-hand dr
Right-hand dr iv
iv e v
e v ehicles:
ehicles: turnthe emer gency
ke y in the opposite direction for each case. Sliding door
Sliding door
Opening/closing t
Opening/closing t
he sliding door fr
he sliding door from outside
om outside &
W WARNING ARNING Risk of becoming trapped due
to an open sliding door which is not
engaged in place
On an incline, the sliding door can mo veby
itself. Opening and closing
55
55

The
following can be found in the st owa gecom-
partment of the centre console depending on the
car's equipment:
R A 12 V soc ket (/ page 104) or the cigar ette
lighter (/ page 104)
R The Media Inter face with two USB ports or
with two USB ports and one SD card slot
R The holder forth e mobile phone cradle
R The ashtr ay (/ page 103)
R A st owage compartment or a device ins talla-
tion frame for auxiliary equipment, e.g. a
ta ch og raph
Opening and closing t
Opening and closing t he stow
he st owag
age com
e com par
partment
tment
under t
under t he ar
he armr
mrest
est #
T
To open:
o open: press button 1.
The st owage compartment opens. #
T To close: o close: presstoclose the caps of the st ow-
age compartment in any order.
Opening and closing t
Opening and closing t he glov
he glove com
e comparpartment
tment &
W
WARNING
ARNING Risk of injury due toobjects
being st owed incor rectly
If objects in theve hicle interior are st owed
incor rectl y,they can slide or be thro wn around
and hit vehicle occupants. In addition, cup
holders, open st owage spaces and mobile
phone brac kets cannot alw aysreta in all
objects they contain.
There is a risk of injur y,particular lyin the
eve nt of sudden braking or a sudden change in
direction. #
Always st owobjects in such a wayth at
th ey cannot be thro wn around in such
situations. #
Always make sure that objects do not
pr otru de from st owage spaces, lug gage
nets or st owage nets. #
Close the loc kable st owage spaces
before starting a jou rney. #
Always st owand secure heavy, hard,
poin ted, sharp-edged, fragile or bulky
objects in the boot. Comply with
the inst ructions for loading theve hi-
cle. 1
Unloc ked
2 Locked
3 Glovecompartment handle #
T To loc o loc k/unloc
k/unloc k:
k:turn the emer gency key a
qu arter turn anti-clockwise 2(to lock) or
clockwise 1(to unlock). #
T
To open:
o open: pull glovecompartment handle 3in
th e direction of the ar row. #
T To close: o close: fold the glo vecompartment handle
up and press it until it engages.
Opening t
Opening t he glasses com
he glasses com par
partment
tment #
Press on the glasses compartment 1. Seats and st
owage
99
99

R
R
eplacing fr
eplacing fr ont light bulbs (v
ont light bulbs (v ehicles wit
ehicles with halog
h halogen
en
headlam
headlam ps)
ps) Ov
Ov
er
ervie
vie w of fr
w of fr ont light sour
ont light sour ce types
ce types 1
Additional turn signal lamp on the outside mir-
ro r: LED
2 Turn signal light: PY 21 W
3 Low beam: H7 55 W
4 High beam/standing/parking lights/d aytime
ru nning lights: H15 55 W/15 W
R
R eplacing light sour
eplacing light sour ces in t
ces in the headla mp
he headlamp
R
R eq
eq uir
uir ements:
ements:
R The lighting system is switched o..
R The appropriate front wheel is turned in wards.
R Lo
Lo w beam:
w beam: youre qu ire a H7 55 W light bulb.
R T
T ur
ur n signal light
n signal light: :yo ure qu ire a PY 21 W light
bulb.
R High beam / st
High beam / st anding/par
anding/parking lights / da y-
king lights / da y-
time r
time r unning lights:
unning lights: youre qu ire a H15 55 W/
15 W light bulb.
F
F itting/r
itting/r emo
emoving t
ving t he cov
he cov er in t
er in the fr
he front wheel ar ch
ont wheel ar ch #
T
To r
o r emov
emov e:
e:grip the centre of co ver1, slide it
upwards and pull it out.
The co ver will hang down wards on the strap. #
T To
o /t:
/t: insert co ver1 attheto p and slide it
down wards until it engages.
Lo
Lo w beam
w beam #
Remo vethe co ver in the front wheel ar ch. #
Turn housing co ver1 anti-clockwise and
re mo veit. #
Turn soc ket2 for low beam tothe leT and
pull it out. #
Pull the bulb out of soc ket2. #
Inse rtthe new bulb into soc ket2. #
Inse rtsoc ket2 and rotate itto theright to
tighten it. #
Press on housing co ver1 and ro tate itto the
ri ght totighten it. #
Replace the co ver in the front wheel ar ch.
High beam, st
High beam, st anding/par
anding/parking lights and da
king lights and da ytime
ytime
r
r unning lights
unning lights #
Open the bonnet. 114
114
Light and vision

#
Turn housing co ver1 anti-clockwise and
re mo veit. #
Pull out the bulb with soc ket2. #
Inse rtthe new bulb with soc ket2 and engage
it as far as it will go. #
Press on housing co ver1 and ro tate itto the
ri ght totighten it. #
Close the bonnet.
T
T ur
ur n signal light
n signal light #
Open the bonnet. #
Turn soc ket1 anti-clockwise and pull it out. #
Pull the bulb out of soc ket1. #
Inse rtthe new bulb into soc ket1. #
Inse rtsoc ket1 and turn it clockwise until it
engages. #
Close the bonnet. R
R
eplacing r
eplacing r ear bulbs
ear bulbs Ov
Ov
er
ervie
vie w of r
w of r ear light sour
ear light sour ce types
ce types Ve
hicles with standard tail lamp
1 Third brake light: LED
2 Licence plate lighting: LED
3 Rear fog light (driver's side): P 21 W
4 Reversing light: P 21 W
5 Brake light, tail light/parking lights: P 21 W
6 Turn signal light: P 21 W
Ve hicles with LED tail lamps 1
Third brake light: LED
2 Licence plate lighting: LED
3 Rear fog light (driver's side): LED
4 Reversing light: W 16 W
5 Brake light, tail light/parking lights: LED
6 Turn signal light: LED
R
R eplacing light sour
eplacing light sour ces in t
ces in the t
he tail lamp
ail lamp
R
R eq
eq uir
uir ements
ements
R The lighting system is switched o..
R St
Standar
andar d t
d tail lam
ail lam p:
p:youre qu ire a P 21 W light
source.
R LED t
LED t ail lam
ail lam p:
p:youre qu ire a W 16 W light
source.
R
R emo
emo ving t
ving t he t
he tail lamp
ail lamp
* NO
NOTE
TEDamage tothe paintwork during tail
lamp remo val The paintwork may be damaged when
theta il
lamps are remo ved. The tail lamp ma y,for
ex ample, scratch the paintwork when it is
re mo ved. #
Remo vetheta il lamps carefull y. #
Mercedes-Benz recommends having the
ta il lamp light sources replaced at a
qu ali/ed specialist workshop. Please no
tethat you can change the bulb of the
re ve rsing light only in the case of an LED tail lamp. #
Open theta ilgate.
% You will /nd a scr ewdriver in theve hicle tool
kit (/ page 250). #
Unscr ewtwo side scr ews1. Light and vision
115
115

#
Push tail lamp 2outwards against bolts 3
as far as it will go. #
Press tail lamp 2o. outwards and away from
bolts 3. #
Pull the connector o. the bulb mount of tail
lamp 2.
Inst
Inst alling t
alling t he t
he tail lamp
ail lamp #
Push the connector into the bulb mount of tail
lamp 2. #
Push tail lamp 2onto bolts 3from the side
and press it against theve hicle. #
Tighten two side scr ews1.
S S t tandar
andar d t
d tail lamp
ail lamp #
Unscr ewthre e scr ews1 and remo vebulb
mount 2from theta il lamp. Bulb mount
3
Turn signal light
4 Brake light, tail light, parking light
5 Reversing light
6 Rear fog light (only on the driver's side) #
Remo vetheta il lamp. #
Gently turn the bulb anti-clockwise and take it
out of the soc ket. #
Push the new bulb into the soc ket and turn it
clockwise toscr ew it in. #
Insert bulb mount 2into theta il lamp and
tighten all thre e scr ews1. #
Installth eta il lamp. LED t LED t
ail lamp
ail lamp #
Remo vetheta il lamp. #
Unscr ewhousing co ver1 byturning it anti-
clockwise. #
Turn the soc ket anti-clockwise and pull it out. #
Pull the bulb out of the soc ket. #
Inse rtthe new bulb into the soc ket. #
Inse rtthe soc ket and rotate it clockwise to
tighten it. #
Press on housing co ver1 and ro tate it cloc k-
wise totighten it. #
Install theta il lamp. R
R
eplacing int
eplacing int er
erior light bulbs
ior light bulbs R
R
eplacing light sour
eplacing light sour ces in t
ces in t he int
he inter
erior
ior
R
R eq
eq uir
uir ements:
ements:
R The interior lighting has been switched o..
R R
Rear and load com
ear and load com par
partment lam
tment lam p:
p:youre qu ire
a T10 6W xenon light sou rce.
R Int
Inter
erior and surr
ior and surr ound lighting:
ound lighting: youre qu ire a
W 5 W light source.
R Signal and ambient lam Signal and ambient lam p in t p in the t
he tailg
ailgat
ate:
e: you
re qu ire a W 5 W light source. 116
116
Light and vision

R
R
ear and load com
ear and load com par
partment lam
tment lam ps
ps #
Push in the catch spring of lens 1with a suit-
able object, e.g. a scr ewdriver, and then prise
o. the lens with the lamp housing. #
Push the lugs of soc ket2 inwa rds. #
Remo velight source 3from the lamp hous-
ing. #
Insert the new light source. #
Position the lens on the lamp housing and
engage it. #
Align the lens with the lamp housing and
engage it.
A
A dditional int
dditional int er
erior and surr
ior and surr ound lighting
ound lighting
Depending on the equipment, replacing the light
sources as described here applies tothefo llowing
lamps:
R The sun visor mir ror lamp
R The ambient lamp at the bottom of the front
door
R The ambient lamp on the inside of theta ilgate #
Push in the catch spring of lamp housing 1
with a suitable object, e.g. a scr ewdriver, and
prise o. lamp housing 1. #
Turn soc ket2 anti-clockwise and pull it out of
lamp housing 1. #
Pull bulb 3out of soc ket2. #
Push new bulb 3into soc ket2. #
Screw soc ket2 into lamp housing 1by
turning it clockwise. #
Place lamp housing 1in position on the leT
and engage it.
Signal and ambient lam
Signal and ambient lam p in t
p in the t
he tailg
ailgate
ate #
Push in the catch spring of the lamp housing
on the side of transparent lens 3with a suita-
ble object, e.g. a scr ewdriver, and prise o. the
lamp housing. #
Turn soc ket2 anti-clockwise and pull it out of
th e lamp housing. #
Pull the bulb out of soc ket2. #
Push the new bulb into soc ket2. #
Screw soc ket2 into the lamp housing by
turning it clockwise. #
Place the lamp housing in position at the side
of red lens 1and engage it. Light and vision
117
117

R
ifth eve hicle is switched on
R when the hot-water auxiliary heater is switched
on Oper
Oper ating air v
ating air v ents
ents A
A
djus
djusting t ting t he air v
he air v ents
ents &
W
WARNING
ARNING Risk of burns or frostbite due to
being too close tothe air vents
Ve ry hot or very cold air can 0ow from the air
ve nts. #
Make sure that all vehicle occupants
alw ays maintain a su1cient dis tance
from the air vents. #
If necessar y,direct the air0ow toano ther
area of theve hicle interior. A
A
djus
djusting t ting t he centr
he centr e air v
e air vents
ents #
T
T o open/close:
o open/close: turn controller 3or4 tothe
leT or right as far as it will go. #
T
T o adjus
o adjust t t the
he air0ow
air0ow dir
dir ection:
ection: hold centre air
ve nt 1 or2 bycont roller 3or4 and
mo veit up or down or tothe leT or right.
A
A djus
djusting t ting t he side air v
he side air v ents:
ents: #
T
T o open/close:
o open/close: turn controller 2clockwise or
anti-clockwise as far as it will go. #
T
T o adjus
o adjust t t the
he air0ow
air0ow dir
dir ection:
ection: hold side air
ve nt 1 bycont roller 2and mo veit up or
down or tothe leT or right. Opening/closing t
Opening/closing t he r
he rear air v
ear air v ents:
ents: 1
Adjustment wheel forve rtically adjusting and
re gulating air0 ow
2 Adjustment wheel for horizontally adjusting
air0ow
The air vents can be adjusted only on vehicles with
re ar-compartment air conditioning. #
T
To open:
o open: turn adjustment wheel 1ofthere ar
air vent tothe centre position. #
T
To close:
o close: turn adjustment wheel 1tothe
upper or lo wer end position. A
A
uxiliar
uxiliar y heating
y heating Inf
Inf
or
ormation about auxiliar
mation about auxiliar y heating
y heating &
D
DAN
AN GER
GER Risk of fata l injury due topoison-
ous exhaust gases
If th eta ilpipe is bloc ked or su1cient ventilation
is not possible, poisonous exhaust gases such
as carbon monoxide may enter theve hicle.
This is the case in enclosed spaces or if the
ve hicle gets stuck in sno w,forex ample. #
Always switch the stationary heater o. in
enclosed spaces without an air extrac-
tion system, e.g. in garage s. #
Keep theta ilpipe and the area around the
ve hicle free from snow when theve hicle
or the stationary heater is running. #
Open a wind owonthe side of theve hicle
fa cing away from the wind toensure an
adequate supply of fresh air. &
W
WARNING
ARNING Risk of /re due tohot stationary
heater components and exhaust gases
Flammable materials such as lea ves, grass or
twigs may ignite. #
When the stationary heater is switched
on, make sure that: Climate cont
rol
129
129