Page 9 of 32
6
Meters and Gauges
Tachometer
Engine coolant temperature gauge
Shift lever indicator
Vehicle information display
Speedometer
Fuel gauge
Page 10 of 32
7
To use the door handles to lock
and unlock your vehicle, make
sure the INFINITI Intelligent
Key is with you (that is, in your
pocket or purse).
•
T
ouch the inside of the door
handle
to unlock the
corresponding front door.
•
Pushing the r
equest switch
while touching the inside
of the door handle will unlock
the rest of the doors.
•
T
o lock the vehicle,
push either door handle
request switch
once.
Locking and Unlocking your
Vehicle via the Door Handle
To change the settings for the door locking and unlocking system,
press the MENU button
, then select the “Settings” key on the
lower display followed by the “Comfort & Convenience” key.
•
T
o unlock all doors by touching the
inside of the door handle, select
“Selective Door Unlock”.
•
T
o disable unlocking by touching the
inside of the door handle, select “Touch Sensitive Door Sensor”.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
REMOTE ENGINE START
(IF SO EQUIPPED)
The remote engine start
system must be enabled in
the vehicle settings within the
lower display. To start your
vehicle remotely:
1.
Pr
ess the lock button
to
lock the vehicle.
2.
Pr
ess and hold the remote
engine start button
within 5 seconds of pressing
the lock button
and the
engine will start.
To start driving, depress the
brake pedal and push the
ignition switch START/STOP
button to the ON position.
State laws may apply, review
local laws before using.
Please see your Owner’s Manual for
important safety information, system
limitations, and additional operating and
feature information.
Infiniti Intelligent Key System
Page 11 of 32
8
Two positions for the driver’s seat, steering
column and outside mirrors can be stored in
the automatic drive positioner memory. To set
a memory position:
1.
Plac
e the ignition switch in the ON
position. (The vehicle should be stopped
while setting the memory.)
2.
A
djust the driver’s seat, steering column
and outside mirrors to the desired
positions using the adjusting switches for each feature.
3
.
Push the
SET switch
, and within 5 seconds, push the memory switch
(1 or 2)
. The indicator light for the memory switch you select will
illuminate for approximately 5 seconds and a chime will sound when the
memory is stored.
The driver’s seat and steering column will automatically move when the driver’s
side door is opened, to allow the driver to get in and out of the driver’s seat
more easily. “Lift Steering upon Exit” and “Slide Driver Seat Back on Exit” can be
adjusted in the lower touch-screen display under “Comfort & Convenience”.
Please see your Owner’s Manual for important safety information, system limitations, and additional
operating and feature information.
Memory Seats (if so equipped)Starting/Stopping
the Engine
It is important to make sure the
INFINITI Intelligent Key is with you
(that is, in your pocket or purse).
1.
Depr
ess the brake pedal.
2.
Push the ignition swit
ch
START/STOP button to
the ON position.
TURNING THE ENGINE OFF
1.
M
ove the shift lever to the P (PARK) position and apply
the parking brake.
2.
Push the ignition swit
ch START/STOP button to turn
the engine off.
Please see your Owner’s Manual for important safety information, system
limitations, and additional operating and feature information.
Page 12 of 32
9
HomeLink® Universal Transceiver (if so equipped)
HomeLink®
Before you start programing HomeLink®, park outside and within range of your garage. Then, clear the area around your garage door, place the
ignition switch in the ON or ACC position (without starting the engine) and locate the remote control transmitter, ensuring a fresh battery is
installed. Please note, a ladder and another person may be needed.
To program the HomeLink
® Universal Transceiver:
1.
P
osition the handheld transceiver 1-3 in (2-8 cm) away from the HomeLink surface, keeping the HomeLink indicator light in view.
2.
Pr
ess and hold the desired HomeLink button and the handheld transmitter button simultaneously until the HomeLink indicator light flashes
slowly and then rapidly.
3
.
Bo
th buttons may be released when the indicator light flashes rapidly.
4.
Pr
ess and hold the programed HomeLink button and observe the indicator light. A solid, continuous light indicates the programing is complete.
If the indicator light rapidly blinks for two seconds and then turns to a solid, continuous light, continue with steps for a rolling code device.
5.
A
t the receiver located on the garage door opener motor, locate the “learn” or “smart” button. If there is difficulty locating the button, reference
the garage door opener’s manual. Once the button is pressed, you have approximately 30 seconds to initiate the next step.
6.
Pr
ess and hold the programed HomeLink button for two seconds and release. Repeat the sequence up to three times to complete the
programing process. HomeLink should now activate your rolling code equipped device.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
Page 13 of 32
10
The climate controls can be adjusted using the buttons on either
side of the lower display or through the “Climate” screen on
the lower display.
•
T
o access the “Climate” screen
, press the CLIMATE button below the lower display.
HEATED STEERING WHEEL (if so equipped)
•
T
o turn the heated steering wheel on or off, select the “Steering
Heater” key
on the lower display.
HEATED SEATS (if so equipped)
The front seats can be warmed by built-in heaters. The heating
system of the driver’s seat and front passenger seat can be
operated independently.
•
Push the heated seat switches
on the instrument panel
or to operate through the touch-screen, press the CLIMATE
button
and select the heated seat key(s) on the lower
display to select the seat heating mode.
Temperature control buttons (driver’s side)
Temperature control buttons (front passenger’s side)
AUTO button
Fan speed buttons
Manual air flow control button
Air recirculation button
Front defroster button
Rear defroster button
ON/OFF button
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
Heater and Air Conditioner (automatic)
Page 14 of 32
11
Power Folding Outside Mirrors (if so equipped)
Adjusting the outside mirrors:
•
T
o adjust the outside mirrors, move the switch
right or left to select the right or left mirror.
•
A
djust the position of the mirror using the mirror control switch
.
Folding the outside mirrors:
•
T
o fold the mirrors closed, push the
switch . To open the mirrors, push the switch .
REVERSE TILT-DOWN FEATURE (IF SO EQUIPPED)
When backing up the vehicle, the outside mirrors will turn downward automatically to provide
better rear visibility. To enable the reverse tilt-down feature, move the switch
to either the left or
right position.
If the switch
is set in the center (neutral) position, the mirror will not tilt down when reversing.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and
feature information.
Page 15 of 32
12
To turn the rain sensor function on and off:
1.
Pr
ess the MENU button below the lower display.
2.
Select the
“Settings” key and then the “Comfort &
Convenience” key
on the display.
3
.
Select the
“Rain Sensor” key
to toggle the
feature ON and OFF.
When the rain-sensing function is disabled, the AUTO
position on the wiper stalk will work in conventional
intermittent mode.
WIPER BLADE REPLACEMENT PROCEDURE
The windshield wipers must be in the service position in order
to replace the wiper blades. To move the wiper blades to the
service position:
• When the ignition swit
ch is in the ON position or within
60 seconds of placing the ignition switch in the OFF
position, lift the windshield wiper and washer lever
upwards twice in less than 0.5 seconds. The windshield
wipers will move to the service position automatically, and
the wiper blades can now be replaced.
To move the wiper blades back to the original position:
•
Plac
e the wiper arm in the down position and lift the wiper
and washer lever up for more than 1 second, or lower the
lever down to operate at any wiper speed.
Wiper and Washer Switch
Move the lever up or down to one of
the following positions to operate the
windshield wipers:
MIST
One sw
eep operation
OFF
Wipers ar
e OFF
AUTO
Speed-sensing and
r
ain-sensing automatic wipe
LO
C
ontinuous wipe, slow
HI
C
ontinuous wipe, fast
To adjust the wiper sensitivity for the AUTO
setting, twist the control ring
.
Pull the lever
toward you to operate the
windshield washer.
Please see your Owner’s Manual for important safety information, system limitations, and additional operating and feature information.
Page 16 of 32
13
Vehicle Information Display
The vehicle information display will provide warnings and information
for items such as:
USING THE VEHICLE INFORMATION DISPLAY
To change the displayed item on the vehicle information
display
, press the or button on the steering wheel.
The odometer and twin trip odometer are displayed in the vehicle
information display when the ignition switch is in the ON position.
RESETTING THE TRIP ODOMETER
Pushing the TRIP RESET switch
under the combination meter
panel changes display to TRIP A or TRIP B.
Pushing the TRIP RESET switch
for more than 1 second resets
the trip odometer to zero.
Please see your Owner’s Manual for important safety information, system limitations, and
additional operating and feature information.
• Automatic Transmission (AT)
•
All-
Wheel Drive (AWD)
•
Cruise C
ontrol
•
In
telligent Cruise Control (ICC)
•
A
ctive Lane Control
•
Lane Departur
e Warning (LDW)/
Lane Departure Prevention (LDP)
•
Blind Spo
t Warning (BSW)
•
Blind Spo
t Intervention
® (BSI)
•
Back-up Collision
Intervention (BCI)
•
Dist
ance Control Assist (DCA)
•
Forward Emergency
Braking (FEB)
•
Predictive Forward
Collision Warning (PFCW)
•
Active Trace Control •
In telligent Key System
