2021 HYUNDAI GENESIS GV70 Owners Manual

Driver Assistance System
7-76
Information
Two red lights may appear on the camera
in the following conditions when:
-The outside brightness is dim or
driving at night
-The vehicle drives inside a building,
such as a basement parking lot, garage
or tunnel
-The camera case of the instrument
cluster is partially broken
:$51,1*
Do not look toward the camera within
8 LQFPIRUORQJHUWKDQDPLQXWH
Limitations of Forward Attention
Warning
Forward Attention Warning may be
limited or may not operate properly in
the following circumstances:
• The driver is wearing sunglasses,
special glasses, infrared cutoff
glasses, refracting glasses or thick
glasses
• The driver has heavy eye makeup
(eyeliner, mascara, color makeup,
false eyelash) or eye piercing
• The driver’s view is blocked by his/her
hair, hat, etc.
• The driver is winking or wearing an
eye patch on one eye
• The driver’s face is covered partially
by a mask, muffler, etc.
• The driver’s view is blocked by
incoming light from outside of the
vehicle • Light from outside, sunlight or infrared
LED light of the camera is reflected by
glasses or sunglasses
• The driver turns or lowers his/her
head so that the face or an eye is
hidden from the camera
• The camera is out of the range to
monitor or close within 8 in. (20 cm)
• The driver shakes his/her head up
and down, or adverse road conditions
cause excessive vehicle vibrations
while driving
• The driver is improperly positioned in
the driver's seat so that the driver’s
face is not detected
• The driver is too tall or short
• The camera is blocked by the adjusted
steering wheel height or the turned
steering wheel
• More than two people are looking at
the instrument cluster simultaneously
from the driver’s seat
• The driver’s eyes are narrowed due to
laughing or sun glare
• Misrecognize a picture or mannequin
that has a similar size of the driver’s
face
• There are other devices using infrared
light in the vehicle

07
7-77
„„Left sideLeft side„„Right sideRight side
OJK071201NOJK071201NOJK071202NOJK071202N
Blind-Spot View Monitor displays the
rear blind spot area of the vehicle in the
cluster when the turn signal is turned on
to help safely change lanes.
Detecting sensor
OJK071049NOJK071049N[1], [2]: Surround-side view camera
(camera located at bottom of the mirror)
Refer to the picture above for the
detailed location of the detecting
sensors.
%OLQG6SRW9LHZ0RQLWRU
Settings
Setting features
Blind-Spot View
With the engine on, select ‘Driver
$VVLVWDQFH

Driver Assistance System
7-78
Blind-Spot View Monitor
Operating conditions
• When the turn signal turns off, the
image on the instrument cluster will
turn off.
• When the hazard warning flasher
is on, Blind-Spot View Monitor will
turn off, regardless of the turn signal
status.
• When other important warning is
displayed on the instrument cluster,
Blind-Spot View Monitor may turn off.
%OLQG6SRW9LHZ0RQLWRU
Malfunction
When Blind-Spot View Monitor is not
working properly, or the cluster display
flickers, or the camera image does
not display properly, have the vehicle
inspected by an authorized retailer of
Genesis Brand products.
:$51,1*
• 7KHLPDJHVKRZQRQWKHFOXVWHUPD\
differ from the actual distance of the
REMHFW0DNHVXUHWRGLUHFWO\FKHFN
WKHYHKLFOH
VVXUURXQGLQJVIRUVDIHW\
• $OZD\VNHHSWKHFDPHUDOHQVFOHDQ
,IWKHOHQVLVFRYHUHGZLWKIRUHLJQ
PDWHULDOLWPD\DGYHUVHO\DIIHFW
FDPHUDSHUIRUPDQFHDQG%OLQG
6SRW9LHZ0RQLWRUPD\QRWRSHUDWH
SURSHUO\

07
7-79
Smart Cruise Control is designed to
help detect the vehicle ahead and
help maintain the desired speed and
minimum distance between the vehicle
ahead.
2YHUWDNLQJ$FFHOHUDWLRQ$VVLVW
While Smart Cruise Control is operating,
if the function judges that the driver is
determined to overtake the vehicle in
front, acceleration will be assisted.
%DVHGRQ'ULYLQJ6W\OHLIHTXLSSHG
Smart Cruise Control will operate based
on the driver’s driving style, such as
inter-vehicle distance, acceleration,
reaction speed.
Detecting sensor
OJK071223NOJK071223N
OJK070075 OJK070075 [1]: Front view camera, [2]: Front radar
The front view camera and front radar
are used as a detecting sensor to help
detect vehicles in front.
Refer to the picture above for the
detailed location of the detecting sensor.
&$87,21
$OZD\VNHHSWKHIURQWYLHZFDPHUD
and front radar in good condition to
maintain optimal performance of Smart
&UXLVH&RQWURO
For more details on the precautions of
WKHIURQWYLHZFDPHUDDQGIURQWUDGDU
UHIHUWR
U)RUZDUG&ROOLVLRQ$YRLGDQFH
$VVLVW)&$
VVHFWLRQLQWKLVFKDSWHU
60$57&58,6(&21752/

Driver Assistance System
7-80
Smart Cruise Control Settings
Setting features
OJK070082OJK070082
To turn on Smart Cruise Control
• Press the Driving Assist () button
to turn on Smart Cruise Control. The
speed will be set to the current speed
on the cluster.
• If there is no vehicle in front of you,
the set speed will be maintained, but
if there is a vehicle in front of you,
the speed may decrease to maintain
the distance to the vehicle ahead. If
the vehicle ahead accelerates, your
vehicle will travel at a steady cruising
speed after accelerating to the set
speed.
Information
If your vehicle speed is between 0~ 20 mph
(0~ 30 km/h) when you press the Driving
Assist (
) button, the Smart Cruise
Control speed will be set to 20 mph (30
km/h).
OJK070088OJK070088
To set vehicle distance
Each time the button is pressed, the
headway changes as follows:
Distance 4 Distance 3
Distance 1Distance 2
Information
• If you drive at 56 mph (90 km/h), the
distance is maintained as follows:
Distance 4 -
approximately 172 ft. (53 m)
Distance 3 -
approximately 130 ft. (40 m)
Distance 2 -
approximately 106 ft. (30 m)
Distance 1 -
approximately 82 ft. (25 m)
• The distance is set to the last set
distance when the engine is restarted,
or when Smart Cruise Control was
temporarily canceled.

07
7-81
OJX1079077OJX1079077
To increase speed
• Push the + switch up and release it
immediately. The cruising speed will
increase by 1 mph (1 km/h) each time
the switch is operated in this manner.
• Push the + switch up and hold it
while monitoring the set speed on
the cluster. The cruising speed will
increase by 5 mph or 10 km/h each
time the switch is operated in this
manner. Release the switch when
the desired speed is shown, and the
vehicle will accelerate to that speed.
You can set the speed to 120 mph
(200 km/h).
:$51,1*
&KHFNWKHGULYLQJFRQGLWLRQEHIRUH
XVLQJWKHVZLWFK'ULYLQJVSHHGPD\
VKDUSO\LQFUHDVHZKHQ\RXSXVKXSDQG
KROGWKHVZLWFK
OJX1079078OJX1079078
To decrease speed
• Push the - switch down and release it
immediately. The cruising speed will
decrease by 1 mph (1 km/h) each time
the switch is operated in this manner.
• Push the - switch down and hold it
while monitoring the set speed on
the cluster. The cruising speed will
decrease by 5 mph or 10 km/h each
time the switch is operated in this
manner.
Release the switch at the speed you
want to maintain. You can set the
speed to 20 mph (30 km/h).

Driver Assistance System
7-82
OJK070050OJK070050
To temporarily cancel Smart Cruise
Control
Press the switch or depress the
brake pedal to temporarily cancel Smart
Cruise Control.
OJK070051OJK070051
To resume Smart Cruise Control
To resume Smart Cruise Control after the
function was canceled, push the +, - or
switch.
If you push the + switch up or - switch
down, vehicle speed will be set to the
current speed on the cluster.
If you push the
switch, vehicle speed
will resume to the preset speed.
:$51,1*
&KHFNWKHGULYLQJFRQGLWLRQEHIRUH
using the VZLWFK'ULYLQJVSHHG
PD\VKDUSO\LQFUHDVHRUGHFUHDVHZKHQ
\RXSUHVVWKH
VZLWFK
OJK070082OJK070082
To turn off Smart Cruise Control
Press the Driving Assist () button to
turn Smart Cruise Control off.
Information
If your vehicle is equipped with Manual Speed
Limit Assist, press and hold the Driving Assist
(
) button to turn off Smart Cruise Control.
However Manual Speed Limit Assist will turn on.
Based on Drive Mode
Smart Cruise Control will change
acceleration based on the drive mode
selected from Drive Mode Integrated
Control system. Refer to the following chart.
'ULYHPRGHSmart Cruise Control
COMFORT Standard
ECO Slow
SPORT Fast
SMART
(if equipped)Standard
CUSTOM
(if equipped)Based on selected
Powertrain mode
Information
• For more details on drive mode, refer
to “Drive Mode Integrated Control
System” section in chapter 6.
• Smart Cruise Control may not turn on
or off in some of the drive modes for the
operating conditions are not satisfied.
• If your vehicle is not equipped with
Drive Mode Integrated Control system,
Smart Cruise Control accelerates your
vehicle at a standard level.

07
7-83
OJK070016LOJK070016L
Based on Driving Style
• With the engine on, if ‘Driver
$VVLVWDQFH