2021 FORD MUSTANG MACH-E light

Note:
If programming a garage door opener
or gate operator, it is advised to unplug the
device during the “cycling” process to
prevent possible overheating.
PROGRAMMING THE GARAGE
DOOR OPENER TO YOUR
HAND-HELD TRANSMITTER
This process is to program your in-vehicle
HomeLink function button with your
hand-held transmitter.
Note: The programming steps below
assume you will be programming HomeLink
that was not previously programmed. If your
HomeLink was previously programmed, you
may need to erase your HomeLink buttons.
See Clearing the Garage Door Opener
(page 147). 1.
With your vehicle parked outside of the
garage, switch your vehicle on, but do
not start your vehicle.
2. Press and release one of the three HomeLink function buttons that you
would like to program.
3. Hold your hand-held garage door transmitter 1– 3 in (2–8 cm) away from
the HomeLink button you want to
program. 4. Press and hold the hand-held
transmitter button you want to
program while watching the indicator
light on HomeLink. Continue to hold
the hand-held button until the
HomeLink indicator light flashes rapidly
or is continuously on.
Note: You may need to use a different
method if you live in Canada or have
difficulties programming your gate operator
or garage door opener. See
Programming
the Garage Door Opener to Your Gate
Opener Motor
(page 147).
5. Press and hold the HomeLink button you programmed for two seconds, then
release. You may need to do this twice
to activate the door.
Note: If the indicator light stays on, the
programming is complete.
Note: If the HomeLink indicator flashes
rapidly, repeat Step 5.
Note: If your device still does not operate,
you must program your garage door. See
Programming the Garage Door Opener to
Your Garage Door Opener Motor
(page
146).
6. To program additional buttons, repeat Steps 1 – 4.
PROGRAMMING THE GARAGE
DOOR OPENER TO YOUR
GARAGE DOOR OPENER
MOTOR 146
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Garage Door OpenerE188212 E142659

1. Press the learn button on the garage
door opener motor, you have 30
seconds to complete the next two
steps.
2. Return to your vehicle. 3. Press and hold one of the three
HomeLink function buttons you want
to program for two seconds, then
release. Repeat this step. Depending
on your brand of garage door opener,
you may need to repeat this sequence
a third time.
PROGRAMMING THE GARAGE
DOOR OPENER TO YOUR GATE
OPENER MOTOR
Gate Operator / Canadian
Programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission –
which may not be long enough for
HomeLink to pick up the signal during
programming. Similar to this Canadian law,
some U.S. gate operators “time-out” in the
same manner.
Note: If programming a garage door opener
or gate operator, it is advised to unplug the
device during the “cycling” process to
prevent possible overheating. 1. Press and release, every two seconds,
your hand-held transmitter until the
HomeLink indicator light changes to a
rapidly blinking or continuously on light.
2. Release the hand-held transmitter button.
3. Press and hold the HomeLink function
button you want to program for two
seconds, then release. You may need
to do this twice to activate the door.
Note: If the indicator light stays on, the
programming is complete.
Note: If the HomeLink indicator flashes
rapidly, repeat Step 3.
Note: If your device still does not operate,
you must program your garage door. See
Programming the Garage Door Opener to
Your Garage Door Opener Motor (page
146).
4. To program additional buttons, repeat Steps 1 – 4.
CLEARING THE GARAGE DOOR
OPENER 1. Press and hold the outer two function
buttons simultaneously for
approximately 10 seconds until the
indicator light above the buttons
flashes rapidly.
147
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Garage Door OpenerE188212 E188213

2. When the indicator light flashes,
release the buttons.
Note: You cannot erase individual buttons.
REPROGRAMMING THE
GARAGE DOOR OPENER
To program a device to a previously trained
button, follow these steps:
1. Press and hold the desired button. Do NOT release the button.
2. The indicator light begins to flash after
20 seconds. Without releasing the
button, follow programming steps.
GARAGE DOOR OPENER
RADIO FREQUENCIES
FCC and RSS-210 Industry Canada
Compliance WARNING: Changes or
modifications not expressively approved
by the party responsible for compliance
could void the user's authority to operate
the equipment. The term "IC:" before the
radio certification number only signifies
that Industry Canada technical
specifications were met.
This device complies with Part 15 of the
FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that could cause undesired
operation. This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment. End Users must
follow the specific operating instructions
for satisfying RF exposure compliance. This
transmitter must be at least
8 in (20 cm)
from the user and must not be co-located
or operating in conjunction with any other
antenna or transmitter.
148
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Garage Door Opener

Connector.
A
Coupler.
B
Control Box.
C
The mobile charger is in the rear luggage
compartment under the load floor and
allows you to charge the vehicle's battery
using a standard household outlet.
You must plug the connector into the
control box first. Then plug the connector
into the household outlet, and then plug
the coupler into the vehicle charge port.
The power indicator illuminates blue when
the connector is properly inserted into the
control box and dedicated wall outlet.
Note: To insert the connector, firmly grasp
the connector by the cable or plug and push
into the control box until an audible click is
heard. Make sure the connector is fully
inserted and flush with the control box
before inserting it into the outlet. Improper
insertion will cause a longer charge session.
Note: Follow the installation instructions
provided with the mobile charger.
Note: We recommend using the supplied
plugs and connectors.
Note: If you do not use a dedicated circuit,
the circuit breaker could trip or open. If a
dedicated circuit is not available, contact a
licensed professional electrician regarding
the installation of a dedicated outlet. Note:
The mobile charger does not charge
and gives a fault indication, if ground is not
present.
Note: Plug the connector for the mobile
charger directly into the wall plug
receptacle. Do not plug the mobile charger
into any form of extension cord.
Note: If the wall bracket is not used for
mounting the charging equipment, plug the
charging equipment into an outlet closer to
ground.
Mobile Charger Indicator Lights Amber Fault Indicator Light.
A
Blue Status Indicator Light.
B
Red Trouble Indicator Light.
C
162
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Charging Your VehicleE336365 E336515

CARE INSTRUCTIONS
Do not use cleaners or solvents as this
could damage your mobile charger. Do not
place stress on the charger cables. If unit
overheats, remove the mobile charger from
direct sunlight.
SAFETY FEATURES
The charger includes the following safety
features to protect against the risk of
electric shock:
•
Service Ground Check: The charger
constantly checks for the presence of
a service ground connection. If the
service ground ever fails, the charger
red indicator turns ON and shuts down
power to the vehicle.
• Thermal Event Sensor: Charger module
senses out-of-ordinary thermal events
and decreases the charging current or
shuts the unit down if required.
• Ground fault circuit interrupter (GFCI)
Protection: The charger has a ground
fault circuit interrupter (GFCI) reaction
system to protect against electric
shock. If the charger module detects
an output ground fault, it shuts down
power to the output cable and
illuminates the red indicator.
• Insulation: The charger module,
connector, cable assembly, and charge
coupler are completely insulated.
There are no exposed live parts, to
protect against electric shock.
• Unintentional Disconnection: The
charge coupler is designed to minimize
unintentional disconnection. A pilot
signal wire in the cable and charge
coupler eliminates the possibility of
electric shock when not connected to
a vehicle or if an unintended disconnect
occurs during a charge. Disconnection
during charging is safe. LOCATING THE CHARGE PORT
The charge port is between the front
left-hand side door and front left-hand
wheel well. To open, press the center
right-hand edge of the charge port door
and then release.
Note:
Do not apply excessive force. Forcing
the door open or closed damages the charge
port.
CHARGE PORT INDICATORS
The charge status indicator is next to the
charging port behind the charge port door.
It indicates the charge status of the high
voltage battery in your vehicle.
Divided into five zones, the charge status
indicator displays the state of charge in 20
percent increments.
The charge status indicator displays how
far along the charge is:
• When zone A is pulsing, the charge is
between 0-20 percent.
• When zone A illuminates, and zone B
is pulsing, the charge is between 20-40
percent.
• When zones A and B illuminate and
zone C is pulsing, the charge is between
40-60 percent.
168
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Charging Your VehicleE317346

•
When zones A, B, and C illuminate, and
zone D is pulsing, the charge is between
60-80 percent.
• When zones A, B, C, and D illuminate,
and zone E is pulsing, the charge is
between 80-100 percent.
• When all zones illuminate, the charge
is 100 percent. Note:
When charging stops, the charge
status indicator shows all the completed
zones solidly illuminated up in a blue color
for 30 seconds before turning off. For
example, if charging stops at 70 percent,
then A, B, and C light up solidly to indicate
a battery charge level of at least 60 percent
but less than 80 percent. Charging stops
when complete or when paused due to
charge settings or charge station actions.
Note: If the charge status indicator does
not light up or pulse after plugging in, please
verify that the charge port light setting is On.
If you do not wish to have the charge status
indicator light up at all while charging, then
you can turn it Off. Locate the charge port
light under the vehicle settings on your
in-vehicle touchscreen.
There are three charge port indicator light
colors, which indicate a specific action:
White is used as a courtesy light to help
with plugging in and to acknowledge
actions such as plugging in and unplugging. Blue is used when the vehicle is plugged in
and either charging or waiting to charge.
Amber is used to indicate charge faults.
Note:
Charging faults are identified by the
color amber on the charge status indicator.
Faults can occur within the vehicle charging
system or outside the vehicle, such as with
the mobile charger, charge station or
electrical supply.
Note: If the system detects a fault in the
vehicle charging system at any point in a
charge cycle, the entire charge status
indicator illuminates solidly in an amber
color for 30 seconds and then turns off. If
this happens, unplug the charge coupler and
then plug it back into the charge port
receptacle. If the problem persists, have
your vehicle serviced as soon as possible.
Note: If the system detects a fault outside
the vehicle, such as with the charge station
or mobile charger, the entire charge status
indicator flashes amber continuously for 30
seconds and then turns off. If this happens
check the mobile charger, charge station or
electrical supply.
AC CHARGING
CONNECTING THE CHARGER Charging Using the Mobile Charger
CAUTION: TO REDUCE THE RISK OF
FIRE- The plug must be properly
grounded. Use a dedicated circuit. If you
do not use a dedicated circuit, the circuit
breaker could trip or open. If you do not
have a dedicated circuit, contact a licensed
professional electrician for proper
installation.
169
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Charging Your VehicleE
D
CA
BE317499 E306677 E306676

To charge the high voltage battery:
You must unwrap the mobile charger
completely before charging.
1. Put the vehicle in park (P).
Note:
Your vehicle must be in park (P) to
charge and for the charge status indicator
to illuminate.
2. Press the center right edge of the charge port door and then release to
open the door.
3. Plug the connector into the control box.
Note: To insert the connector, firmly grasp
the connector by the cable or plug and push
into the control box until an audible click is
heard. Make sure the connector is fully
inserted and flush with the control box
before inserting it into the outlet. Improper
insertion will cause a longer charge session
or faults.
4. Plug the connector into the wall outlet.
5. Confirm that the mobile charger's indicators illuminate.
6. Plug the charge coupler into the charge
port receptacle on your vehicle. Note:
Make sure the button clicks
confirming that you have completely
engaged the coupler. When you plug in your
vehicle, it starts charging to 100% by default
unless scheduled charging has been set up
for this location. See Setting the Charging
Schedule and Preferences (page 174).
Note: Plug the connector into the wall
outlet before connecting the charge coupler
to your vehicle's charge port.
Note: When the handle is properly engaged
the light ring illuminates. This indicates the
beginning of a normal charge cycle.
Note: There could be a delay in light ring
illumination due to vehicle internal
communications.
Note: If charging for your vehicle fails,
please contact the Customer Relationship
Center, or click on Live chat. To ensure
superior service, please take note of your
serial number when contacting customer
support.
For more information, visit
www . o wner .f or d . c om .
Charging At a Charge Station
1. Put your vehicle in park (P).
Note: Your vehicle must be in park (P) to
charge.
170
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Charging Your VehicleE335725 E329078

2.
Press the center right hand edge of the
charge port door and then release to
open the door.
3. Select the appropriate charge station coupler.
4. Plug the charge coupler into the charge
port receptacle on your vehicle. Note:
Make sure the button clicks
confirming that you have completely
engaged the coupler. When you plug in your
vehicle, it starts charging to 100% by default
unless scheduled charging has been set up
for this location. See Setting the Charging
Schedule and Preferences (page 174).
Note: When the handle is properly engaged
the light ring illuminates. This indicates the
beginning of a normal charge cycle. Note:
There could be a delay in light ring
illumination due to vehicle internal
communications.
Information about public charge stations
is available through the in-vehicle screen
as well as the FordPass app with pricing,
power levels, and real time availability.
Rates for charging varies by power level,
provider, location, and time of day.
When charging your vehicle at a FordPass
Charging Network station, use the
FordPass App to activate and pay for
charging. You can also just plug in to
activate charging at Plug & Charge capable
stations. If the charging station is not in the
FordPass Charging Network, use the
directions on the charge station to activate
the charger.
For more information, visit
www . o wner .f or d . c om .
STOPPING CHARGING WARNING:
To safely discontinue
charging at any time, follow the
disconnect instructions in stopping
charging. Charging will automatically and
safely come to a stop. The BLUE
STATUS indicator remains ON solid
when the coupler is removed.
Using the mobile charger:
1. Push the latch and remove the charge coupler from the vehicle.
2. Remove the connector plug from the wall outlet.
Note: Do not pull the wall plug from the
wall or the connector from the mobile
charger control box, while your vehicle is
charging. Doing so could damage the outlet
and the cord.
171
2021 Mustang Mach-E (CGW) Canada/United States of America, Vehicles Built From: 07-06-2021, enUSA, Edition date: 202104, First-Printing Charging Your VehicleE335725 E329078