G
WARNING
During chargingand jump-starting, explosivegase scan escap efrom thebattery .There isa
risk ofan explo sion.
Particu larlyavoi dfire, open flames,creating sparksand smoking. Ensurethereissuffi cient
ventila tionwhilechargi ngand jump-starting. Donot leanover abattery . G
WARNING
During thechargi ngprocess ,a battery produceshydrogen gas.Ifashort circuitoccurs or
spar ksare created ,the hydrogen gascan ignite. Thereisarisk ofan explo sion.
R Make surethattheposi tive terminal ofaconnected batterydoesnotcome intocontact with
vehicl eparts.
R Never placemetal objects ortools onabattery .
R Itis impor tantthatyouobse rvethe descri bedorder ofthe battery terminal swhen connect-
ing and disconnecting abattery .
R When jump-starting, makesurethatthebattery poleswith identical polarityareconnected.
R Itis particu larlyimpor tanttoobse rvethe descri bedorder whenconnecting anddisconnect-
ing the jumper cables.
R Never connect ordisconnect thebattery terminal swhi lethe engine isrunning. G
WARNING
A discha rgedbattery canfreeze attempera turesbelow freezing point.Whenjump-starting the
vehicl eor chargi ngthe battery ,gase scan escap efrom thebattery .There isarisk ofan explo -
sion.
Allow thefrozen battery tothaw outbefore chargingitor jump-starting.
! Avoid
repeatedand lengthy starting attempts. Otherwise,the catal yticconverter couldbe
dama gedbythe non-combusted fuel.
If the indica tor/warni nglamp sdo not light up atlow tempera tures,itis very likelythat thedis-
charge dbattery hasfrozen. Inthis case, youmay neither chargethebattery norjump-start the
vehicl e.The service lifeofathawe d-outbattery maybeshorter. Thestarting characteristics can
be impa ired,particu larlyat low tempera tures.Havethethawe d-outbattery checked ataqua li-
fied speci alist worksho p.
Do not start thevehicl eusi ng arapi dchargi ngdevi ce.Ifyou rvehicl e'sbattery isdischa rged,the
engine canbejump-started fromanother vehicleor from adonor battery using jumper cables.
Observe thefollowi ngpoints:
R The battery isnot accessi bleinall vehicl es.Ifthe other vehicle'sbattery isnot accessi ble,
jump-start thevehicl eusi ng adonor battery orajump-starting device.
R You may onlyjump-start thevehicl ewhen theengine andexhau stsystem arecold.
R Do not start theengine ifthe battery isfrozen. Letthe battery thawfirst.
R Only jump-start frombatterie swith a12 Vvoltag erating.
R Only usejumper cableswhi chhave asuffi cient cross-section andinsul ated terminal clamps.
R Ifthe battery isfull ydischa rged,leavethe battery thatisbei ng used tojump-start connected
for afew minutes beforeattempting tostart. Thischarge sthe battery slightly.
R Make surethatthetwo vehicl esdo not touch. Jump-star
ting
289Breakdown assistance Z
Make
surethat:
R The jumper cablesarenot damaged.
R Bare parts ofthe terminal clampdonot come intocontactwith other metal partswhile the
jumper cablesareconn ected tothe battery.
R The jumper cablescannot comeintocontactwith parts which canmove whentheengine is
running, suchasthe V-belt pulleyor the fan.
X Secure thevehicle byapply ingthe electric parking brake.
X Shift thetransmission toposition 005D.
X Make surethattheignition isswitched off.Allindicator lampsinthe instrumen tcluster must
be off. When usingtheSmartK ey,turn theSmartK eytoposition 0092inthe ignition lockand
remove it(Y page 126).
X Switch offallelectrical consumers, e.g.rear window defroster, lighting,etc.
X Open thehood. Position
number0084identifies thecharged batteryofthe other vehicle oran equival entjump-
startin gdevice.
X Press cover0043ofpositive terminal 0044down (inthe direction ofthe arrow) andturn itclock-
wise. Toexpose positive terminal 0044,press cover 0043down further.
X Connect positiveterminal 0044onyour vehicle topositive terminal 0087ofdonor battery 0084using
the jumper cable,alwaysbegin withpositive terminal 0044onyour ownvehicle first.
X Start theengine ofthe donor vehicle andrunitat idling speed.
X Connect negative terminal0085ofdonor battery 0084toground point0083ofyour vehicle usingthe
jumper cable,beginning withdonor battery 0084first.
X Start theengine.
X Before disconnec tingthejumper cables,letthe engine runforseveral minutes.
X First, remove thejumper cablesfromground point0083and negative terminal0085,then from
positive terminal 0044and positive terminal 0087.Begin eachtimeatthe cont acts onyour own
vehicle first.
X Aft erthe jumper cableisremoved, returncover0043ofpositive terminal 0044tothe original posi-
tion. Positive terminal 0044iscovered upand thus insulated again.
X Have thebattery checkedataqual ified specialist workshop.
Jump-starting isnot considered tobe anormal operating condition. 290
Jump
-startingBr eakdown assistance
When
towing away,useatowing ropeora
towing barwith both axles onthe ground. Do
not use anytow barsystems. Towing
thevehicle withtherear axle
raised
! The
ignition mustbeswitched offifyou
are towing thevehicle withtherear axle
raised. Interven tionbyESP®
could other-
wise damage thebrake system.
! Vehicles
withautomatic transmission must
not betowed withtherear axle raised. The
vehicle/t railercombin ationmayotherwise
swerve oreven rollover. Tr
anspor tingthevehicle
Vehicles withautomat ictransmission !
When
thevehicle isloaded fortran sport,
the fron tand rear axles mustbestation ary
and onthe same transportat ionvehicle.
Position ingover theconn ection pointofthe
tran sport vehicle isnot permitt ed.The drive
train mayotherwise bedamaged.
All vehicles !
You
may onlysecure thevehicle bythe
wheels, notbyparts ofthe vehicle suchas
axle orsteerin gcompon ents.Other wise, the
vehicle couldbedamaged.
The towing eyecan beused topull thevehicle
ont oatrailer ortran sporter fortran sportin g
purposes. X
Turn theSmart Keytoposition 0048inthe igni-
tion lock.
X Shift thetran smission toposition 005C.
As soon asthe vehicle hasbeen loaded:
X Preven tthe vehicle fromrolling awayby
applying theelectr icparking brake.
X Shift thetran smission toposition 005D.
X Turn theSmart Keytoposition 0092inthe igni-
tion lock andremove it.
X Secure thevehicle. Tow-sta
rting (emergency engine
star ting)
! Vehicles
withautomatic transmission must
not betow-s tarted. You could otherwise
damage theautomatic transmission.
You canfind inform ationon"Jump-start ing"at
(Y page 288). Fuses
Impor
tantsafety notes G
WARNIN
G
If you manipulate orbridge afaulty fuseorif
you replace itwith afuse withahigher
amperage, theelectr iccables couldbeover-
loaded. Thiscould result inafire. There isa
risk ofan accident andinjury.
Always replace faultyfuseswiththespeci-
fied new fuses having thecorr ectamperage.
Blown fusesmustbereplaced withfuses of
the same rating,which youcan recogn izeby
the color andvalue. Thefuse rating sare listed
in the fuse allocation chart.
The fuse allocation chartislocated inthe vehi-
cle tool kitinthe stowage compartmentunder
the trun kfloor (Ypage 280).
If anewly insertedfuse alsoblows, havethe
cause tracedand rectified ataqualified spe-
cialist workshop, e.g.anauthorized Mercedes-
Benz Center .
! Only
usefuses thathave been approved
for Mercedes- Benzvehicles andwhich have
the corr ectfuse rating forthe system con- Fuses
293Breakdown assistance Z
cerned
.Other wise, comp onents orsystems
cou ldbe damag ed.
! Ma
kesure that nomoi stur ecan enter the
fus ebox whenthe cover isope n.
! Whe
nclos ingthe cover ,make sure that it
is lying corre ctlyonthe fusebox. Moistur e
see ping inor dirt cou ldothe rwiseimp airthe
ope rationofthe fuses.
The fusesinyour vehi cleserv eto clos edow n
fau ltycircu its.Ifafus eblow s,allthe comp o-
nents onthe circu itand theirfuncti onsstop
ope rating. Befo
rechan ging afuse
X Swi tch offthe engi ne.
X Swi tch offallel ectri calconsu mers.
X Ma kesure that theignition isswi tched off
(Y page 126 ).
or X Whe nus ing the SmartK ey,turn theSmart-
Key topos ition 0092 inthe ignition lock and
remo veit(Y page 126 ).
X Secu rethe vehi cleagainst rolling away
(Y page 147 ).
All indi cator lamps inthe instru ment cluster
mus tbe off.
The fusesare loca tedinvari ousfus eboxe s:
R Fus ebox inthe engi necomp artme nton the
rig ht-ha ndsideof the vehi cle,whe nvie we d
in the directi onoftrave l
R Dash boardfus ebox
R Fus ebox inthe rearcomp artme nton the
rig ht-ha ndsideof the vehi cle,whe nvie we d
in the directi onoftrave l Das
hboard fuse box
i Obs
erve the"Important safety notes" sec-
tion (Ypage 293 ).
! Do
not useapoi nted objectsuch asa
screw driver toope nthe cover inthe dash-
boa rd.You couldda mag ethe dashb oard or
the cover . X
Ope nthe driver' sdoo r.
X To ope n:pullcover 0043outwa rds inthe
di recti onofthe arrow and remo veit.
X To clos e:clipin cover 0043onthe front ofthe
da shb oard.
X Fold cover 0043inw ardsunti lit enga ges. Fus
ebo xin the engine compartment
i Obs
erve the"Important safety notes" sec-
tion (Ypage 293 ). G
WARNI
NG
Whe nthe hoodis ope nand thewindsh ield
wi per sare setinmotio n,youcan beinju red
by the wiper linkage .The reisaris kof inju ry.
Alw aysswi tch offthe windsh ield wiper sand
the ignition before opening thehood. X
Ope nthe hood.
X Use adry cloth toremo veany moistur e
from thefusebox.
X To ope n:ope ncla mps 0044.
X Fold cover 0043ofthe fusebox upinthe
di recti onofthe arrow and remo veit. 294
Fus
esBreakdo wnassi stanc e
R
The jack must beplaced onafirm, flatand
non- slipsurface. Onaloose surface, alarge,
flat, load-bearing underlaymustbeused. On
a slippery surface, anon- slipunderlay must
be used, e.g.rubber mats.
R Do not use wooden blocksorsimilar objects
as ajack underlay. Otherwise, thejack will
not beable toachieve itsload-bearing capa-
city due tothe restr icted height.
R Make surethatthedistance between the
underside ofthe tires andtheground does
not exceed 1.2in(3 cm).
R Never placeyourhands andfeet under the
raised vehicle.
R Do not lieunder thevehicle.
R Do not start theengine whenthevehicle is
raised.
R Do not open orclose adoor orthe trunk lid
when thevehicle israised.
R Make surethatnopersons arepresent in
the vehicle whenthevehicle israised.
Vehicles withalloy wheels andhub caps:
the wheel boltsarecovered byahub cap.
Before youcan unscrew thewheel bolts,you
must remove thehub cap. Twodifferent var-
iants canbeinstalled. X
To remove: takesocket 0044and lugwrench
0087 from thevehicle toolkit(Ypage 280).
X Position socket0044onhub cap0043.
X Position lugwrench 0087onsocket 0044.
X Using lugwrench 0087,turn hubcap0043coun-
ter- clock wiseandremove it.
X To install: beforeinstalling, checkhub
cap 0043and thewheel areaforsoiling and
clean ifnecessary.
X Put hub cap0043inposition andturn until itis
in the right position. X
Position socket0044onhub cap0043.
X Attach lugwrench 0087tosocket 0044and
tighten hubcap0043.
The tighten ingtorque mustbe
18 lb-ft (25Nm).
i Note
thatthehub capshould betight-
ened tothe specified torqueof18 lb-ft
(25 Nm). Mercedes- Benzrecomm endsthat
you have thehub capinstalled ataqualified
specialist workshop. X
Using lugwrench 0087,loosen thebolts on
the wheel youwish tochange byabout one
full turn. Donot unscrew thebolts com-
pletely. The
jackingpoints arelocated justbehind the
front wheel housings andjust infront ofthe
rear wheel housings (arrows).
Mercedes-AMG vehiclesandvehicles with
AMG equipm ent:toprotec tthe vehicle body,
the vehicle hascovers installed nexttothe
jack ingpoints onthe outer sills. 318
Changing
awheelWheels andtires
data
isdifferen tfor every vehicle andcan
deviate fromthedata shown here.Youcan
find thedata applicable toyour vehicle on
the vehicle identification plate. Vehicle
identification number(VIN) X
Move thefron t-passenger seatasfar back
as possible.
X Fold upfloor cover ing0043infron tof the
fron t-passenger seat.
You willsee VIN 0044.
The VINcanalso befound inthe following
location s:
R on the lower edgeofthe windshield
(Y page 324)
R on the vehicle identification plate
(Y page 323) Engine
number 0043
Emiss ioncontrol infor mation plate,includ-
ing the cert ification ofboth federal and
Californian emissionsstan dards
0044 Engine number (stamped intothe cran k-
case)
0087 VIN (onthe lower edgeofthe windshield) Service
product sand filling capaci-
ties Impor
tantsafet ynotes G
WARN
ING
Serv iceproduct smay bepoisonous andhaz-
ardous tohealth. Thereisarisk ofinjury.
Comply withinstruct ions onthe use, storage
and disposal ofservic eproduct son the
labels ofthe respect iveoriginal container s.
Always storeservic eproduct ssealed intheir
original container s.Always keepservic e
product sout ofthe reach ofchildren . H
Environm
entalnote
Dispose ofservic eproduct sin an envir on-
ment allyrespon siblemann er.
Serv iceproduct sinclude thefollowing:
R Fuels
R Lubrican ts(e.g. engin eoil, tran smission oil)
R Coolant
R Brak efluid
R Windshield washerfluid
R Climate control system refrigerant
Comply withallvalid regulation swith respect
to handling, storing, and disposing ofservic e
fluids.
Componen tsand servic eproduct smust
matc h.You should therefore onlyuseproduct s
that have been testedand approved by
Mercedes -Benz.
Inf ormat ionabout testedand approved prod-
ucts canbeobtained fromanauthoriz ed
Mercedes -BenzCenter oron the Internet at
htt p:// bevo.m ercedes- benz.com.
You canident ifyserv iceproduc tsapprove dby
Merc edes- Benzby the followin ginsc riptions
on the contain er:
R MB- Freigabe (e.g.MB-Freigabe 229.51)
R MB- Appr oval(e.g. MB-Appr oval229.51)
Oth erdesign ationsor rec omme ndations indi-
cat ealevel ofquality oraspecif ication in
acco rdanc ewith anMB Shee tNumber (e.g.
MB 229 .51). They have notnecessarily been
approve dby Merc edes- Benz. 324
Serv
iceproduct sand filling capacitiesTechnical data
Other
identifications, forexample:
R 0W-30
R 5W-30
R 5W-40 Fuel
Importa ntsafety notes G
WARNING
Fuel ishighly flammabl e.Improper handling
of fuel creates arisk offire and explosion.
Avoid fire,open flames, smoking andcreat-
ing sparks underallcircumstances. Switch
off the engine and,ifappli cable, theauxili ary
heating beforerefueling. G
WARNING
Fuels aretoxic andharmful tohealth. There
is arisk ofinjury.
You must avoid fuelscoming intocontact
with skin, eyesandclothes orbeing swal-
lowed.
Do not inhale thefuel vapors. Keepchildren
awa yfrom fuels.
Keep doors andwindows closedduringthe
refueling process.
If you orothers comeintocontactwith fuel,
observe thefollowi ngpoints:
R Immediately rinsethefuel offyour skin
with soap andwater.
R Ifyou getfuel into your eyes, immediately
rinse youreyes throughly withclean
water. Seekmedical attentionimmedi-
ately.
R Seek medical attentionimmediately iffuel
has been swallowed. Donot induce vomit-
ing.
R Immediately changeoutofclothing which
has come intocontactwith fuel. Tank
capacity Model Total
capa-
city All
models 19.8
USgal
(75 .0l) Model Of
whic h
reserve Merce
des‑AMGvehic les Approx.
3.7 USgal
(14.0 l) Al
lot her models Approx.
2.4 USgal
(9.0 l) Gasol
ine Fue
lgrade
! Do
not use diesel torefue lvehicl eswith a
gaso lineengine. Donot switch onthe igni-
tion ifyou accid entall yrefue lwith thewrong
fuel .Otherwi se,the fuel willenter thefuel
system .Even smallamou ntsofthe wrong
fuel couldresu ltin dama getothe fuel sys-
tem andtheengine. Notifyaqua lified spe-
cial istworksho pand have thefuel tank and
fuel lines drained comple tely.
! Only
refue lusi ng premi um-gra deunle aded
gaso linewith atlea st95 RON thatconforms
to Europe anstanda rdEN 228 oran equ iva-
lent speci ficatio n.
Fuel ofthis speci ficatio ncan contain upto
10% ethanol .You rvehicl eis E10-compati-
ble .You canrefue lyou rvehicl eusi ng E10
fuel .
Fuel thatdoes notconform toEN 228 can
lea dto increas edwea ras wel las dama geto
the fuel system ,engine andexhau stsystem .
! Only
usethefuel recommende d.Opera ting
the vehicl ewith other fuelscan leadto dam-
age tothe fuel system ,engine andexhau st
system .
Observ ethe notes onopera tingfluids.
! Never
refuelusi ng:
R Diesel
R Reg ulargaso linewith anoctane number
low erthan 91RON Servi
ceproducts andfilling capaci ties
325Techn ical data Z
Mercedes-Ben
z.You must observe thenotes
and mixing ratiosspecified onthe cont ainer. Engine
oil
General notes !
Do
not use engine oiloran oilfilter with
specifications deviatingfromthose
expressly requiredforthe prescribed service
intervals. Donot change theengine oiloroil
filter inorder toset replacement intervals
longer thanthose prescribed. Thiscould
otherwise causedamage tothe engine or
exhaust gasaftertr eatment .
Follow theinstruct ionsonthe service inter-
val display forchanging theengine oil.This
could otherwise causedamage tothe
engine orexhaust gasaftertr eatment .
When handling engineoil,observe theimpor-
tant safety notesonservice products
(Y page 324).
The engine oilsarematched tothe perform-
ance ofMercedes-Ben zengines andservice
intervals. Youshould therefore onlyuseengine
oils and oilfilters thatareapproved forvehi-
cles with maintenanc esystems.
For alist ofapproved engineoilsand oilfilters,
consult anauthorized Mercedes-Ben zCenter.
Or visit thewebsite
http: //bevo.m ercedes-benz .com.
The table shows whichengine oilshave been
approved foryour vehicle. Model MB-Freigabe
orMB-App roval All
models 229.
5 Mercedes‑AMG
vehicles:use only
SAE 0W-40 orSAE 5W-40 engine oils. i
MB
approval isindicated onthe oilcon-
tainers.
Fill ing capacities The
following valuesrefertoan oilchange
including theoilfilter.
Missing valueswerenotavaila bleattime of
going toprint. Model Capacity
SL
450 6.9
USqt(6.5l) SL
550 8.5
USqt(8.0l) Merce
des-AMG
SL 63 8.9
USqt(8.5 l) Ad
diti ves !
Do
not useany additive sin the engi neoil.
Thi scou ldda mag ethe engi ne. Brake
fluid G
WARNI
NG
The brakefluidconsta ntlyabsorb smoi stur e
from theair. Thi slo we rsthe boiling pointof
the brakefluid.If the boiling pointofthe
bra kefluidistoo low, vap orpocke tsmay
form inthe brakesystem when the brakes
are applied ha rd. Thiswo uld imp airbra king
effi ciency. Thereisaris kof an acci dent.
Yo usho uld ha ve the brakefluidrene wedat
the specified inter vals.
Whe nha ndl ing brakefluid,obs erve theimpor-
tant safety notes onservice products
(Y page 324 ).
The brakefluidcha nge inter valscan befou nd
in the Maintena nceBookl et.
Only usebra kefluidap pro ved byMer cedes-
Benz inacco rdance with MB-Fre igab eor MB-
Appr oval331.0.
Infor mationabou tap pro ved brakefluidcan be
obta inedat any qualifi ed spe cialist wo rksho p
or on the Interne tat
http://b evo.merce des-benz.co m.
i Have
thebrakefluidregu larly repl aced ata
qu alifi ed spe cialist wor kshop andthe Servi
ceproducts andfilling capac ities
327Tec hnical data Z