2020 DODGE DURANGO Vehicle Warranty

•EXPLOSION OF TIRE/RIM ASSEMBLY DUE TO IMPROPER
MOUNTING. Only specially trained persons should mount tires.
• FAILURE TO MOUNT RADIAL TIRES ON APPROVED RIMS.
• FAILURE TO DEFLATE SINGLE OR DUAL ASSEMBLIES COM-
PLETELY BEFORE DEMOUNTING.
• TIRE SPINNING. On slippery surfaces such as snow, mud, ice, etc.,
do not spin tires in excess of 35 mph (55 kph), as indicated on the
speedometer.
• EXCESSIVE WHEEL SPINNING. This can also result in tire disinte-
gration or axle failure.
WARNING!
Vehicle handling, traction, ride comfort and other performance
parameters may be significantly affected by a change in tire size or
type. Before replacing tires, always consult and follow the vehicle
owner ’s manual because some vehicle manufacturers prohibit
changing tire size. When selecting tires that are different from the
original equipment size make certain:
1. The tires have adequate load-carrying capacity based on the vehicle placard,
2. The tires have sufficient inflation pressure to carry the load and
3. There is proper clearance with no interference points between the tire and vehicle.
The consumer must be aware to always drive safely and obey all
traffic laws. Avoid sudden, sharp turns or aggressive lane changes.
Failure to follow any of these warnings may result in loss of control
of the vehicle, leading to an accident and serious injury or death.
TIRE CARE AND MAINTENANCE GUIDE
The easiest way to help ensure satisfactory mileage and performance
from your Goodyear or Dunlop tires is to give them a simple but frequent
(at least monthly) inspection for proper inflation, even tread wear and the
presence of any damage.
DO MAINTAIN PROPER INFLATION PRESSURE IN YOUR TIRES
Proper inflation pressure is necessary for optimum tire performance,
safety and fuel economy. Check inflation pressures at least once a month
and before long trips. Use an accurate tire pressure gauge. Always check
GOODYEAR DUNLOP TIRES
128

pressures when the tires are cold (when the vehicle has been driven less
than one mile). If you must check inflation when the tires are hot, add
4 psi (27 kPa) to the recommended cold inflation pressure. It is difficult
to tell just by looking at radial tires whether they are underinflated.*
Furthermore, when operating a vehicle equipped with radial tires, it is
difficult to notice when a tire has gone flat or nearly flat since the “feel”
of the vehicle does not change significantly.
*Evidence of air loss or repeated underinflation always requires expert
inspection to determine the source of leakage and tire removal to
determine repairability.To avoid injury, NEVER attempt to reinflate a
tire that has been run severely underinflated. Progressive air loss may
result from punctures, cuts, curbing, impacts or partial bead unseating.
Some fitment causes for air loss are (1) incomplete bead seating, (2) bead
tearing caused by a machine tool due to insufficient lubrication or
improper adjustment. Leaking valve core or rubber valve components
should be replaced when problems are detected and whenever tires are
replaced.
Always maintain inflation pressure at the level recommended by the
vehicle manufacturer as shown on the vehicle placard, vehicle certifi-
cation label or in the vehicle owner ’s manual:
Under inflation is the leading cause of tire failure and may result in
severe cracking, component separation or “blowout.” It reduces tire load
capacity, allows excessive sidewall flexing and increases rolling resis-
tance, resulting in heat and mechanical damage. Maintaining proper
inflation pressure is the single most important thing you can do to
promote tire durability and maximize tread life.
Over inflation increases stiffness, which may deteriorate ride and gener-
ate unwanted vibration. Over inflation also increases the chances of
impact damage.
DON’T OVERLOAD YOUR VEHICLE
Check your vehicle owner ’s manual to determine the load limits.
Overloading your vehicle places stress on your tires and other critical
vehicle components. Overloading a vehicle can cause poor handling or
increased fuel consumption and may cause tire failure. Overloading your
tires can result in severe cracking, component separation or “blowout.”
Never fit your vehicle with new tires that have less load capacity than
shown on the vehicle tire placard and remember that optimum rim width
GOODYEAR DUNLOP TIRES
129

GOODYEARDUNLOPTIRES
is
important
for
proper
tire
load
distribution
and
function.
The
maximum

load
capacity
stamped
on
the
sidewalls
of
P-Metric
&
European
Metric

tires
is
reduced
by
10%
when
used
on
a
light
truck,
utility
vehicle
or

trailer.
Never
fit
P-Metric
or
European
Metric
tires
to
light
trucks
that

specify
LT-type
replacement
tires.
DON’TSPINYOUR TIRES EXCESSIVELY
Avoid
excessive
tire
spinning
when
your
vehicle
is
stuck
in
snow,
ice,

mud
or
sand.
The
centrifugal
forces
generated
by
a
free-spinning

tire/wheel
assembly
may
cause
sudden
tire
explosion,
resulting
in

vehicle
damage
and/or
serious
personal
injury
to
you
or
a
bystander.

Never
exceed
35
mph
/
55
kph,
as
indicated
on
your
speedometer.
Use
a

gentle


backward
and
forward
rocking
motion
to
free
your
vehicle
for

continued
driving.
Never
stand
near
or
behind
a
tire
spinning
at
high

speeds,
for
example,
while
attempting
to
push
a
vehicle
that
is
stuck
or

when
an
on-the-car
spin
balance
machine
is
in
use.
DO CHECK YOUR TIRES FORWEAR
Always
remove
tires
from
service
when
they
reach
two
thirty-seconds
of

an
inch
(2/32)
remaining
tread
depth.
All
new
tires
have
tread
wear

indicators
which
appear
as
smooth
banks
in
the
tread
grooves
when
they

wear
to
the
two
thirty
seconds
of
an
inch
(2/32)
level.
Many
wet
weather

accidents
result
from
skidding


on
bald
or
nearly
bald
tires.
Excessively

worn
tires
are
also
more
susceptible
to
penetrations.
DO CHECK YOUR TIRES FORDAMAGE
Frequent
(at
least
monthly)
inspection
of
your
tires
for
signs
of
damage

and
their
general
condition
is
important
for
safety.
If
you
have
any

questions,
have
your
tire
Dealer
inspect
them.
Impacts,
penetrations,

cracks,
knots,
bulges
or
air
loss
always
require
tire
removal
and
expert

inspection.
Never
perform
a
temporary
repair
or
use
an
inner
tube
as
a

substitute
for
a
proper
repair

.
Only
qualified
persons
should
repair
tires.
PROPER TIREREPAIR
NOTE:

Goodyear
does
not
warrant
any
inspection
or
repair
process.
The

repair
is
entirely
the
responsibility
of
the
repairer
and
should
be

made
in
accordance
with
established
Rubber
Manufacturers
Association

(RMA)
procedures.
130

Tire Pressure Monitoring System Alert
Refer to your vehicle Owner ’s Manual for more information on what to
do if the tire pressure warning system activates.
THE CONVENIENCE (TEMPORARY) SPARE
The Convenience (Temporary) Spare is designed, built and tested to the
high engineering standards set by North America’s leading car manufac-
turers and to Goodyear ’s own high standards of quality control. It is
designed to take up a minimum of storage space and, at the same time,
fulfill the function of a spare tire when needed. The spare is kept in its
storage space, fully inflated at 60 psi. To be sure it is always ready for use,
the air pressure should be checked on a regular basis.
The Convenience (Temporary) Spare can be used in combination with the
original tires on your vehicle. You can expect a tire tread life of up to 3,000
miles (4,800 kilometers), depending on road conditions and your driving
habits. To conserve tire tread life, return the spare to the storage area as
soon as it is convenient to have the standard tire repaired or replaced.
The Convenience (Temporary) Spare weighs less than a standard tire so
it’s easier to handle. It also helps reduce the total car weight, which
contributes to fuel economy. The wheels used with the Convenience
(Temporary) Spare are specifically designed for use with high pressure
spares and should never be used with any other type tire.
DON’T ATTEMPT TO MOUNT YOUR OWN TIRES
Serious injury or death may result from explosion of tire/rim assembly
due to improper mounting procedures. Follow tire manufacturer ’s
instructions and match tire diameter to rim diameter. Mount light truck
radials on rims approved for radial service. Do not apply bead sealer.
This can inhibit bead seating. Lubricate beads and tire rim (including
tube or flap) contact surfaces. Lock assembly on mounting machine or
place in safety cage. STAND BACK and never exceed 40 psi to seat beads.
Never use a volatile substance or a rubber “donut” (also known as a bead
expander or “O-Ring”) to aid bead seating. Only specially trained
persons should mount tires.
GOODYEAR DUNLOP TIRES
131

DON’T MIX TIRES OF DIFFERENT SIZES AND TYPES ON THE
SAME AXLE
For optimum handling and control, Goodyear recommends fitment of
four (4) tires of the same type and size unless otherwise specified by the
vehicle manufacturer.
WARNING!
Before you replace your tires, always consult the vehicle owner ’s
manual and follow the vehicle manufacturer ’s replacement tire
recommendations. Vehicle handling may be significantly affected
by a change in tire size or type. When selecting tires that are
different from the Original Equipment size, see a professional
installer in order to make certain that proper clearance, load-
carrying capacity and inflation pressure are selected. Never exceed
the maximum load capacity and inflation pressure listed on the
sidewall of the tire. Always drive safely and obey all traffic laws.
Avoid sudden, sharp turns or aggressive lane changes. Failure to
follow this warning may result in loss of control of the vehicle,
leading to an accident and serious injury or death.
When replacing tires, you must maintain the outside diameter and
load-carrying capacity of the Original Equipment tire. Inflation pressure
may need to be adjusted to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or JATMA standards
for correct load and inflation information.
NEVER FIT TIRES TO A VEHICLE THAT HAVE LESS LOAD-
CARRYING CAPACITY THAN REQUIRED BY THE ORIGINAL
EQUIPMENT MANUFACTURER
Examples: Many vehicles, such as large passenger vans, require Load
Range E tires as designated by the vehicle manufacturer. Fitment of a tire,
such as a Load Range D, with less carrying capacity is not allowed. In
other cases, tires of the same size may carry different load indexes in the
service description. You must make certain the replacement tires fitted to
the vehicle have a load-carrying capacity equal to or greater than what
the Original Equipment manufacturer specifies.
GOODYEAR DUNLOP TIRES
132

NOTE:

Goodyear
manufactured
and/or
marketed
European-
Metric

passenger
tires
and
P-Metric
passenger
tires
are
interchangeable
as
long

as
they
have
the
same
section
width,
same
aspect
ratio,
same
rim

diameter.
CAUTION!
Never substitute a “Standard Load” (SL) tire for an Extra Load (XL)
or Reinforced tire. If the vehicle was originally equipped with
“Extra Load” (XL) or Reinforced tires, replace those tires with
similar-sized Extra Load (XL) or Reinforced tires.
GOODYEAR DUNLOP TIRES
FOLLOW THESE ADDITIONAL GUIDELINES
When
installing
only
two
tires,
fit
the
tires
with
the
deepest
tread
depth

on
the
rear
axle.
If
radials
and
non-radials
must
be
fitted
to
the
same

vehicle,
fit
radials
on
rear
axle.
Never
mix
radials
and
non-radials
on
the

same
axle.
When
fitting

tires
or
all-season
tires
to

performance
vehicles,
always
fit
in
sets
of
four.
It
is
not

recommended
to

fit
tires
with
different
speed
ratings.
If
tires
with
different
speed
ratings

are
installed
on
a
vehicle,
they
should
be
installed
with
like
pairs
on

the
same
axle.
The
speed
capability
of
the
vehicle
will
become
limited
to
that
of
the

lowest
speed
rated
tires.
Use
of
lift
kits
with
some
vehicle/tire
combinations
can
cause
instability.

When
changing
tire


sizes,
always
consult
Dealer
for
optimum
rim
width

and
carefully
check
vehicle/tire
clearances.
RETREADED TIRES
Retreaded
passenger
and
light
truck
tires
are
not
warranted
by
Goodyear

for
any
reason.
Speed
ratings
and
U.S.
Department
of
Transportation
test

compliance
certifications
are
voided
for
retreaded
tires.
DOMAINTAIN VEHICLESUSPENSION, WHEELALIGNMENT
AND BALANCE AND ROTATE YOURTIRES
Lack
of
rotation,
worn
suspension
parts,
underinflation/

overinflation,
wheel
imbalance
and
misalignment
can
cause
vibration

or
irregular
tire
wear.
Rotate
your
tires
according
to
your
vehicle

manufacturer ’s
recom-mendations
or
at
maximum
intervals
of
6,000

miles
/
10,000
km.
133

TIRE SERVICE LIFE
Tires are designed and built to provide many thousands of miles of
excellent service. For maximum benefit, tires must be maintained prop-
erly to avoid tire damage that may result in removal from service before
the tread is worn down to minimum depth.
It is not practical to accurately predict the service life of any specific tire
in chronological time since service conditions vary widely. The service-
ability of a tire over time is a function of the storage and service
conditions (inflation pressure, load, speed, road hazard injury, etc.) to
which a tire is subjected. Consumers should not rely solely on the
appearance of the tire, but should be aware of any change in dynamic
performance such as increased air loss, noise or vibration, which could be
a sign to remove the tire. Therefore, it is essential to have tires, including
spares, inspected regularly (at least monthly) for proper inflation pres-
sure, damage and treadwear.
Check your vehicle’s owner ’s manual (or your vehicle) to determine if
it is equipped with run-flat (extended mobility) tires. If your vehicle is
equipped with run-flat tires, the following applies:
GOODYEARDUNLOPTIRE6
HOWTOREAD A TIRE D.O.T. SERIAL NUMBER
D.O.T.
stands
for
Department
of
Transportation
and
the
number
is
on
the

lower
sidewall
of
each
tire
to
show
that
the
tire
meets
or
exceeds
the

Department
of
Transportation
safety
standards.
134

RUN-FLAT TECHNOLOGY EXTENDED MOBILITY TECHNOLOGY
(EMT™), RUNONFLAT® (ROF) AND DUNLOP SELFSUPPORTING
TECHNOLOGY (DSST®) ORIGINAL EQUIPMENT TIRES
IMPORTANT SAFETY INFORMATION
OPERATIONAL MONITORING
The information contained in this Limited Warranty Brochure applies
only to the Original Equipment tires supplied with your vehicle. In order
for Goodyear Run-Flat (Extended Mobility Technology [EMT], RunOn-
Flat [ROF]) or Dunlop Run-Flat (Dunlop Self- Supporting Technology
[DSST]) tires to obtain the performance criteria stated within this Limited
Warranty, Goodyear or Dunlop Run-Flat tires must use specific parts,
such as a low tire pressure monitoring system authorized by the Original
Equipment vehicle manufacturer.
RUN-FLAT TIRE FEATURE:
The Goodyear or Dunlop Run-Flat tire is a high-performance tire with a
remarkable feature: It can operate for limited distances with very low or
even no inflation pressure (refer to your Vehicle Owner ’s Manual for
these limitations). This is an important benefit, especially if inflation loss
occurs at a location where immediately stopping your vehicle could be
hazardous. TIRE PRESSURE MONITORING SYSTEM ALERT Refer to
your vehicle Owner ’s Manual for more information on what to do if the
tire pressure warning system activates.
WARNING!
If the tire pressure-monitoring system signals an alert, follow these
safety precautions to prevent a loss of vehicle control that could
result in serious personal injury or death:
•Slow your speed. Do not exceed 50 mph (80 kph).
• Avoid hard cornering, hard braking and severe handling maneu-
vers.
• Avoid potholes and other road hazards.
Remember that when your tires have lost air pressure, your vehicle’s
handling capability is reduced, particularly during severe
maneuvers.
GOODYEAR DUNLOP TIRES
135