
192STARTING AND OPERATING  
Tongue Weight (TW)
The tongue weight is the downward force 
exerted on the hitch ball by the trailer. You must 
consider this as part of the load on your vehicle.
Trailer Frontal Area
The frontal area is the maximum height 
multiplied by the maximum width of the front of 
a trailer.
Trailer Sway Control
The Trailer Sway Control (TSC) can be a 
mechanical telescoping link that can be 
installed between the hitch receiver and the 
trailer tongue that typically provides adjustable 
friction associated with the telescoping motion 
to dampen any unwanted trailer swaying 
motions while traveling.
If equipped, the electronic TSC recognizes a 
swaying trailer and automatically applies 
individual wheel brakes and/or reduces engine 
power to attempt to eliminate the trailer sway.
Weight-Carrying Hitch
A weight-carrying hitch supports the trailer 
tongue weight, just as if it were luggage located 
at a hitch ball or some other connecting point of 
the vehicle. These kinds of hitches are the most 
popular on the market today and they are 
commonly used to tow small and medium sized 
trailers.
Weight-Distributing Hitch
A weight-distributing system works by applying 
leverage through spring (load) bars. They are 
typically used for heavier loads to distribute 
trailer tongue weight to the tow vehicle's front 
axle and the trailer axle(s). When used in 
accordance with the manufacturer's directions, 
it provides for a more level ride, offering more 
consistent steering and brake control thereby 
enhancing towing safety. The addition of a 
friction/hydraulic sway control also dampens 
sway caused by traffic and crosswinds and 
contributes positively to tow vehicle and trailer  stability. Trailer sway control and a weight 
distributing (load equalizing) hitch are 
recommended for heavier Tongue Weights (TW) 
and may be required depending on vehicle and 
trailer configuration/loading to comply with 
Gross Axle Weight Rating (GAWR) requirements.
WARNING!
An improperly adjusted Weight Distributing 
Hitch system may reduce handling, 
stability, braking performance, and could 
result in a collision.
Weight Distributing Systems may not be 
compatible with Surge Brake Couplers. 
Consult with your hitch and trailer manufac
-
turer or a reputable Recreational Vehicle 
dealer for additional information.
20_LX_OM_EN_USC_t.book  Page 192   

STARTING AND OPERATING193
TRAILER HITCH CLASSIFICATION
The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you 
in selecting the correct trailer hitch for your intended towing condition.
Trailer Hitch Classification Definitions
  
Class Max. Trailer Hitch Industry Standards
Class I - Light Duty 2,000 lbs (907 kg)
Class II - Medium Duty 3,500 lbs (1,587 kg)
Class III - Heavy Duty 6,000 lbs (2,722 kg)
Class IV - Extra Heavy Duty 10,000 lbs (4,535 kg)
Refer to the “Trailer Towing Weights (Maximum Trailer Weight Ratings)” chart for the Maximum Gross Trailer Weight (GTW) towable for your given 
drivetrain.
All trailer hitches should be professionally installed on your vehicle.
5
20_LX_OM_EN_USC_t.book  Page 193   

194STARTING AND OPERATING  
TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS)   
NOTE:
The trailer tongue weight must be considered as 
part of the combined weight of occupants and 
cargo, and it should never exceed the weight 
referenced on the “Tire and Loading Informa -
tion” placard. Refer to “Tire Safety Information” 
in “Servicing And Maintenance” for further infor -
mation.TRAILER AND TONGUE WEIGHT 
Never exceed the maximum tongue weight 
stamped on your bumper or trailer hitch.
Weight Distribution
 Consider the following items when computing 
the weight on the rear axle of the vehicle:The tongue weight of the trailer.
The weight of any other type of cargo or 
equipment put in or on your vehicle.
The weight of the driver and all passengers.
NOTE:
Remember that everything put into or on the 
trailer adds to the load on your vehicle. Also, 
additional factory-installed options or 
dealer-installed options must be considered as 
part of the total load on your vehicle. Refer to 
the “Tire And Loading Information” placard for 
the maximum combined weight of occupants 
and cargo for your vehicle.
Engine/Transmission Frontal AreaMax. GTW (Gross Trailer 
Weight) Max. Tongue Weight 
(See Note)
3.6L Automatic 22 sq ft (2.04 sq m)1,000 lbs (454 kg)100 lbs (45 kg)
5.7L Automatic 32 sq ft (2.97 sq m)1,000 lbs (454 kg)100 lbs (45 kg)
Refer to local laws for maximum trailer towing speeds.
20_LX_OM_EN_USC_t.book  Page 194   

STARTING AND OPERATING195
(Continued)
TOWING REQUIREMENTS
To promote proper break-in of your new vehicle 
drivetrain components, the following guidelines 
are recommended. Perform the maintenance listed in the 
“Scheduled Servicing”. Refer to “Scheduled 
Servicing” in “Servicing And Maintenance” for 
the proper maintenance intervals. When towing 
a trailer, never exceed the GAWR or GCWR 
ratings.
Towing Requirements — Tires
Do not attempt to tow a trailer while using a 
compact spare tire.
Do not drive more than 50 mph (80 km/h) when towing while using a full size spare tire.
Proper tire inflation pressures are essential 
to the safe and satisfactory operation of your 
vehicle. Refer to “Tires” in “Servicing And 
Maintenance” for proper tire inflation proce -
dures.
Check the trailer tires for proper tire inflation 
pressures before trailer usage.
WARNING!
Make certain that the load is secured in the 
trailer and will not shift during travel. When 
trailering cargo that is not fully secured, 
dynamic load shifts can occur that may be diffi -
cult for the driver to control. You could lose 
control of your vehicle and have a collision.
When hauling cargo or towing a trailer, do 
not overload your vehicle or trailer. Over -
loading can cause a loss of control, poor 
performance or damage to brakes, axle, 
engine, transmission, steering, suspension, 
chassis structure or tires.
Safety chains must always be used 
between your vehicle and trailer. Always 
connect the chains to the hook retainers of 
the vehicle hitch. Cross the chains under 
the trailer tongue and allow enough slack 
for turning corners.
Vehicles with trailers should not be parked 
on a grade. When parking, apply the 
parking brake on the tow vehicle. Put the 
tow vehicle transmission in PARK. Always, 
block or "chock" the trailer wheels.
GCWR must not be exceeded.
Total weight must be distributed between 
the tow vehicle and the trailer such that the 
following four ratings are not exceeded :
Max loading as defined on the “Tire and 
Loading Information” placard.
GTW
GAWR
Tongue weight rating for the trailer 
hitch utilized.
WARNING! (Continued)CAUTION!
Do not tow a trailer at all during the first 
500 miles (805 km) the new vehicle is 
driven. The engine, axle or other parts could 
be damaged.
Then, during the first 500 miles (805 km) 
that a trailer is towed, do not drive over 
50 mph (80 km/h) and do not make starts 
at full throttle. This helps the engine and 
other parts of the vehicle wear in at the 
heavier loads.
5
20_LX_OM_EN_USC_t.book  Page 195   

196STARTING AND OPERATING  
Check for signs of tire wear or visible tire 
damage before towing a trailer. Refer to 
“Tires” in “Servicing And Maintenance” for 
the proper inspection procedure.
When replacing tires, refer to “Tires” in 
“Servicing And Maintenance” for the proper 
tire replacement procedures. Replacing tires 
with a higher load carrying capacity will not 
increase the vehicle's GVWR and GAWR limits.
Towing Requirements — Trailer Brakes
Do not interconnect the hydraulic brake 
system or vacuum system of your vehicle 
with that of the trailer. This could cause inad -
equate braking and possible personal injury.
An electronically actuated trailer brake 
controller is required when towing a trailer 
with electronically actuated brakes. When 
towing a trailer equipped with a hydraulic 
surge actuated brake system, an electronic 
brake controller is not required.
Trailer brakes are recommended for trailers 
over 1,000 lbs (453 kg) and required for 
trailers in excess of 2,000 lbs (907 kg).
Towing Requirements — Trailer Lights And 
Wiring
Whenever you pull a trailer, regardless of the 
trailer size, stoplights and turn signals on the 
trailer are required for motoring safety.
The Trailer Tow Package may include a four- and 
seven-pin wiring harness. Use a factory 
approved trailer harness and connector.
NOTE:
Do not cut or splice wiring into the vehicle’s 
wiring harness.
The electrical connections are all complete to 
the vehicle but you must mate the harness to a 
trailer connector. Refer to the following 
illustrations.
NOTE:
Disconnect trailer wiring connector from the 
vehicle before launching a boat (or any other 
device plugged into vehicle’s electrical 
connect) into water.
Be sure to reconnect after clear from water 
area.
WARNING!
Do not connect trailer brakes to your 
vehicle's hydraulic brake lines. It can over -
load your brake system and cause it to fail. 
You might not have brakes when you need 
them and could have an accident.
Towing any trailer will increase your stop -
ping distance. When towing, you should 
allow for additional space between your 
vehicle and the vehicle in front of you. 
Failure to do so could result in an accident.
CAUTION!
If the trailer weighs more than 1,000 lbs
(453 kg) loaded, it should have its own 
brakes and they should be of adequate 
capacity. Failure to do this could lead to 
accelerated brake lining wear, higher brake 
pedal effort, and longer stopping distances.
20_LX_OM_EN_USC_t.book  Page 196   

STARTING AND OPERATING197
Four-Pin Connector
Seven-Pin Connector
TOWING TIPS 
Before setting out on a trip, practice turning, 
stopping, and backing up the trailer in an area 
located away from heavy traffic.
Automatic Transmission
Select the DRIVE range when towing. The 
transmission controls include a drive strategy to 
avoid frequent shifting when towing. However, if 
frequent shifting does occur while in DRIVE, you 
can use the AutoStick shift control (if equipped) 
to manually select a lower gear.
NOTE:
Using a lower gear while operating the vehicle 
under heavy loading conditions will improve 
performance and extend transmission life by 
reducing excessive shifting and heat buildup. 
This action will also provide better engine 
braking.
Speed Control — If Equipped
Do not use on hilly terrain or with heavy 
loads.
When using the Speed Control, if you experi-
ence speed drops greater than 10 mph 
(16 km/h), disengage until you can get back 
to cruising speed.
Use Speed Control in flat terrain and with 
light loads to maximize fuel efficiency.
1 — Ground
2 — Park
3 — Left Stop/Turn
4 — Right Stop/Turn1 — Battery
2 — Backup Lamps
3 — Right Stop/Turn
4 — Electric Brakes
5 — Ground
6 — Left Stop/Turn
7 — Running Lamps
5
20_LX_OM_EN_USC_t.book  Page 197   

198STARTING AND OPERATING  
AutoStick — If Equipped
When using the AutoStick shift control, select 
the highest gear that allows for adequate 
performance and avoids frequent down -
shifts. For example, choose “5” if the desired 
speed can be maintained. Choose “4” or “3” 
if needed to maintain the desired speed.
To prevent excess heat generation, avoid 
continuous driving at high RPM. Reduce 
vehicle speed as necessary to avoid 
extended driving at high RPM. Return to a 
higher gear or vehicle speed when grade and 
road conditions allow.
Cooling System 
To reduce potential for engine and transmission 
overheating, take the following actions:
City Driving
In city traffic — while stopped, place the trans -
mission in NEUTRAL, but do not increase 
engine idle speed.
Highway Driving
Reduce speed.
Temporarily turn off air conditioning.
RECREATIONAL TOWING (BEHIND 
MOTORHOME, ETC.)   
Recreational towing (with all four wheels on the 
ground, or using a tow dolly) is  NOT ALLOWED. 
The only acceptable method for towing this 
vehicle (behind another vehicle) is on a vehicle 
trailer with all four wheels  OFF the ground.
DRIVING TIPS
DRIVING ON SLIPPERY SURFACES
Information in this section will aid in safe 
controlled launches in adverse conditions.
Acceleration
Rapid acceleration on snow covered, wet, or 
other slippery surfaces may cause the driving 
wheels to pull erratically to the right or left. This 
phenomenon occurs when there is a difference 
in the surface traction under the rear (driving) 
wheels.
CAUTION!
Towing this vehicle in violation of the above 
requirements can cause severe transmission 
and/or transfer case damage. Damage from 
improper towing is not covered under the New 
Vehicle Limited Warranty.
WARNING!
Rapid acceleration on slippery surfaces is 
dangerous. Unequal traction can cause 
sudden pulling of the front wheels. You could 
lose control of the vehicle and possibly have a 
collision. Accelerate slowly and carefully 
whenever there is likely to be poor traction 
(ice, snow, wet, mud, loose sand, etc.).
20_LX_OM_EN_USC_t.book  Page 198   

202IN CASE OF EMERGENCY  
ASSIST Call
The ASSIST Button is used to automatically 
connect you to any one of the following support 
centers:
Roadside Assistance – If you get a flat tire, or 
need a tow, just push the ASSIST button and 
you will be connected to a representative for 
assistance. Roadside Assistance will know 
what vehicle you’re driving and its location. 
Additional fees may apply for roadside Assis -
tance.
SiriusXM Guardian™ Customer Care – 
In-vehicle support for SiriusXM Guardian™.
Vehicle Customer Care – Total support for all 
other vehicle issues.
SOS Call
1. Push the SOS Call button on the Rearview  Mirror.
NOTE:
In case the SOS Call button is pushed in error, 
there will be a 10 second delay before the SOS 
Call system initiates a call to a SOS operator. To 
cancel the SOS Call connection, push the SOS  call button on the Rearview Mirror or press the 
cancellation button on the Device Screen. 
Termination of the SOS Call will turn off the 
green LED light on the Rearview Mirror.
2. The LED light located between the ASSIST 
and SOS buttons on the Rearview Mirror will 
turn green once a connection to a SOS 
operator has been made.
3. Once a connection between the vehicle and  a SOS operator is made, the SOS Call 
system may transmit the following 
important vehicle information to a SOS 
operator: Indication that the occupant placed a 
SOS Call.
The vehicle brand.
The last known GPS coordinates of the 
vehicle.
4. You should be able to speak with the SOS  operator through the vehicle audio system 
to determine if additional help is needed. NOTE:
Your vehicle may be transmitting data as 
authorized by the subscriber.
Once a connection is made between the 
vehicle’s SOS Call system and the SOS oper
-
ator, the SOS operator may be able to open a 
voice connection with the vehicle to deter -
mine if additional help is needed. Once the 
SOS operator opens a voice connection with 
the vehicle’s SOS Call system, the operator 
should be able to speak with you or other
WARNING!
ALWAYS obey traffic laws and pay attention to 
the road. ALWAYS drive safely with your hands 
on the steering wheel. You have full 
responsibility and assume all risks related to 
the use of the Uconnect and SiriusXM 
Guardian™ features and applications in this 
vehicle. Only use Uconnect features and 
SiriusXM Guardian™ services when it is safe 
to do so. Failure to do so may result in an 
accident involving serious injury or death.
20_LX_OM_EN_USC_t.book  Page 202