2019 YAMAHA YXZ1000R SS Owners Manual

8-22
8
11. Add 2.00 L (2.11 US qt, 1.76 Imp.qt) ofthe recommended engine oil to the oil
tank.
12. Check the O-ring for damage, and re- place it if necessary. 13. Install and tighten the engine oil tank filler
cap and the cylinder head cap.
14. Start the engine, warm it up for several minutes, and then turn it off.
15. Remove the engine oil tank filler cap, and then add sufficient oil of the recommend-
ed type to raise it to the maximum level
mark on the dipstick.Tightening torques:Engine oil drain bolt:10 N·m (1.0 kgf·m, 7.4 lb·ft)
Engine oil tank drain bolt: 16 N·m (1.6 kgf·m, 12 lb·ft)
1. Engine oil tank filler cap
2. O-ring
3. Cylinder head cap
3
2
1
2
UB5H7AE0.book Page 22 Wednesday, July 4, 2018 1:37 PM

8-23
8
TIPBe sure to wipe off spilled oil on any parts af-
ter the engine and exhaust system have
cooled down. 16. Install and tighten the engine oil tank fillercap.
17. Start the engine and let it idle for several minutes. During this time, check for oil
leakage. If any oil leaks are found, stop
the engine and check for the cause.
18. Stop the engine, wait at least ten minutes, and then check the oil level one last time.
19. Install the engine oil tank cover by install- ing the bolts.
20. Install the panel.
To change the engine oil and oil filter
1. Park the vehicle on a level surface.
2. Loosen the left and right side panels by removing the bolt as shown. 3. Remove the rear bottom panel by remov-
ing the bolts.
1. Left side panel
2. Right side panel
3. Bolt
3
1
3
2
UB5H7AE0.book Page 23 Wednesday, July 4, 2018 1:37 PM

8-24
8
4. Remove the bolts, and then slide the cen-ter bottom panel rearward to remove it. 5. Follow steps 2–9 of the “To change the
engine oil” section for the oil draining pro-
cedure.
6. Remove the oil filter cartridge with an oil filter wrench. Make sure the O-ring is re-
moved together with the oil filter car-
tridge. If the O-ring remains attached to
the crankcase, oil leakage may occur.1. Rear bottom panel
2. Bolt
2
1
2
2
1. Center bottom panel
2. Bolt
2
2
2
2
2
1
UB5H7AE0.book Page 24 Wednesday, July 4, 2018 1:37 PM

8-25
8
TIPAn oil filter wrench is available from a Yamaha
dealer. 7. Apply a light coat of clean engine oil to
the O-ring of the new oil filter cartridge.TIPMake sure that the O-ring is properly seated.
8. Install the new oil filter cartridge, and thentighten to the specified torque.
1. Oil filter cartridge
2. Oil filter wrench
2
1
1. O-ringTightening torque:Oil filter cartridge:17 N·m (1.7 kgf·m, 13 lb·ft)
1
UB5H7AE0.book Page 25 Wednesday, July 4, 2018 1:37 PM

8-26
8
9. Follow steps 10–20 of the “To change theengine oil” section for the oil filling proce-
dure.
10. Slide the front portion of the center bot- tom panel into place as shown, and then
hook the left and right sides of the center
bottom panel into place.
11. Install the center bottom panel bolts, andthen tighten them to the specified torque.1. Torque wrench
1
1. Center bottom panel
1. Center bottom panel
1
1
UB5H7AE0.book Page 26 Wednesday, July 4, 2018 1:37 PM

8-27
8
12. Install the rear bottom panel by installingthe bolts, and then tightening them to the
specified torque.
1. Bolt A
2. Bolt B
3. Bolt C
1
2
3
1. Bolt A
2. Bolt B
3. Bolt CTightening torques:Bolt A:7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt B: 7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt C: 7 N·m (0.7 kgf·m, 5.2 lb·ft)1
3
2
3
UB5H7AE0.book Page 27 Wednesday, July 4, 2018 1:37 PM

8-28
8
13. Install the side panel bolts, and then tight-en them to the specified torque.
EBU35107Transmission oilCheck the oil level and change the transmis-
sion oil at the intervals specified in the general
maintenance and lubrication chart.
1. Rear bottom panel
2. Bolt A
3. Bolt BTightening torques:Bolt A:7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt B: 7 N·m (0.7 kgf·m, 5.2 lb·ft)
3
1
2
2
1. Bolt BTightening torque: Bolt B:7 N·m (0.7 kgf·m, 5.2 lb·ft)
1
1
UB5H7AE0.book Page 28 Wednesday, July 4, 2018 1:37 PM

8-29
8
NOTICEECB02910When checking or changing the transmis-
sion oil, make sure that no foreign material
enters the transmission. If necessary,
clean the filler cap and surrounding area. To check the transmission oil level1. Park the vehicle on a level surface.
2. Remove panel B. (See page 8-11.)
3. Remove the transmission oil filler cap, wipe the dipstick clean, insert it back into
the transmission case (without screwing
it in), and then remove it again.
TIPThe transmission oil level should be between
the tip of the dipstick and the maximum level
mark. 4. If the oil level is at or below the tip of thedipstick, add oil.
Recommended oil:YA M A L U B ESAE 5W-30, 10W-30, 10W-40, 15W-40,
20W-40 or 20W-50
Oil quantity: 1.50 L (1.59 US qt, 1.32 Imp.qt)
1. Transmission oil filler cap
2. O-ring
3. Dipstick
4. Maximum level mark
5. Tip of the dipstick
1 3
245
UB5H7AE0.book Page 29 Wednesday, July 4, 2018 1:37 PM