2019 MERCEDES-BENZ SPRINTER MY19 with no MMS Operator’s Manual

light
weight loads. La yanti-slip mats underneath
th el oad tosecur ethe load additionally. Installing and
removing tie-down eyes #
Toinstall: slidethet ie-down eyet hrough a
re cess in thel oading rail close tothel oad
until locking mechanism engages in the
re cess.
% Whe
nyou pull locking mechanism up and out
of ther ecess, thet ie-down eyeisa bleto
mo vewithin thel oading rail. Mak esuret hat
locking mechanism is alw ayse ngaged in a
re cess. #
Che ckthet ie-down eyef or firm seating. #
Toremo ve: pull lo cking mechanism up and
pull thet ie-down eyet ow ards thel ocking
mechanism and out of thel oading rail
th ro ugh arecess. Car
rier sy stems Information abou
tthe roof rack &
WARNING Risk of inju rydue tothem axi‐
mum roof load being exceeded
When youp laceal oad on ther oof as well as
all outer and inner attachments, thev ehicle's
center of gr avity will rise and thef amiliar driv‐
ing characteristic saswell asthes teering and
braking characteristic swillch ange. When
drivin garound bends, thev ehicle will tilt
mor eheavily and ma yreact mor esluggishly
to steering mo vements.
If yo ue xceed them aximum roof load, the
driving characteristics, as well as thes teering
and braking, will be greatl yimp aired. #
Nevere xceed them aximum roof load
and adjus tyour driving style. 1
Mountin grails
Informatio nabout them aximum roof load can be
fo und in the" Tech nical data" section
(/ page246).
Obse rvet he following point sfor assembling roof
ra ck s:
R Tighten ther oof rack 's scr ewstoat orque of
6.0 lb-f t(8N m)–7.4 lb-f t(10 Nm) in thed es‐
ignated groo vedp lates.
R The tightened scr ewsshould no ttouc hthe
ra ils.
R Ensur ethat theg roove dplates ar enotloca‐
te dint he areas around thep lastic caps.
R The groo vedp lates mus thave ther ight cross-
sectio n.
R The insides of them ounting rails mus tbefree
of dirt.
R Re-tigh tent he scr ewsu niformly af tera round
300 mile s(500 km).
Mercedes-Benz recommends that youu se on ly
ro of rack st hat ha vebeen tested and appr oved
fo rM ercedes-Benz. These help topreve ntvehicle
damage.
If yo uw ant toretrofit them ounting rails, ha ve
th em ins talled at aqualified specialis tworks hop.
Otherwise, youc oul dd amag ethe vehicle.
If yo ur vehicle is ins talled wit hmountin grails on
th er oof, youc an install aroof rack on ther oof.
Special fastener s(sliding bloc ks)a re available as
accesso ries fort his purpose.
These fastener sareavailable from an yauthorized
Mercedes-Ben zCenter. Tr
ansporting 16 9

Using the interior
roof car rier sy stem &
WARNING Risk of inju rydue tounse‐
cured loads
When yous ecur eorl oosen aload, thel oad
ma yfall down and injur evehicle occupants. #
When securing or loosening aload, do
no ts tand unde rthe load. *
NO
TERisk of damag etothe belt stra ps
and slider Excessiv
epoint loading on theb elt stra ps and
slider smaycause theb elt stra ps totear or cause
thes lider stob reak of ffro mt herack
ra il. #
Distribut ethe load evenly. When doing
so, ensur ethat theo verall cen terof
gr av ity of thel oad is alw aysasc loseto
th ec enter as possible and between the
ro of rails and between ther ackr ails. Yo
uc an use thei nterior roof rack system to
secur eloads. It is also suitable fors ecuring long
loads.
% The interior
roof rack system ma ybesubjec‐
te dtoam aximum load of 110l bs (50 kg).
The interior roof rack system consists of thef ol‐
lowing components:
R Roofrails 1 area ttached tother oof of the
ve hicle.
R Rack rails 2 ares crew ed ont othe roof rails
and can be mo ved.
R Rack rail2 is equipped wit hslider pair 4.
Slider pair 4witha ttached belt strap 5can
be mo ved. Load 6isstowe dbyp lacing and
lashing it in belt strap 5.
R The load has tobe secured in thed irection of
tra vela nd in theo pposit edirection tothe direction of tra
velu sing tw ohead lashings
3. 17 0
Transporting

#
Tomo vether ackr ails: unscr ewstar knobs
7 coun ter-clockwise until they ares lightly
loose. #
Sliderackr ail 2 along roof rail1 tothe
desired position. #
Screw star knobs 7tight clo ckwise. #
Chec kthat ther ackr ail is seated securely.
Moving thes liders &
WARNING Risk of inju rydue toinade‐
qu atel ysecured loads
If th es lider of thei nterior roof rack system is
no te ngaged proper ly,t he load ma ycome
loose, fall down and injur epeople, for
ins tance when they enter or load and unload
th ec argo compartment. #
Alwayse ngag ethe slider properly. %
Ring
8of slider 4mus talway sbeatan
angle of 90° torack rail2,sot hat slider 4
is engaged proper ly. #
When ther ing of thes lider is at an angle
of 90° tother ackr ail: pullring 8of slider
4 down an dsimul taneously mo veslider 4
to thed esired position. #
Release ring 8 atthed esired position. #
Moveslider 4slightl yfurther along on rack
ra il2 until slider 4engages automaticall y.#
When ther ing of thes lider is pa rallel to
th er ackr ail: moveslider 4tothed esired
position. #
Position ring 8 of slider 4at an angle of
90° torack rail2.
Slider 4is engaged. Ad
justin gthe belt strap #
Press and hold thel ocking mechanism on
slider 9. #
Pull or release belt strap 5. #
Release thel ocking mechanism on slider 9.
% When securing or loosening
aload, be sure
to nots tand unde rthe load.
Securing and loosening thel oad #
Tosecur ethe load: placethel oad in theb elt
st ra ps of ther ackr ails. #
Fasten thel oad flush wit hthe partition. #
Secur ebelt strap 5. #
Chec kthat thel oad is seated securel y. #
Toloosen thel oad: press and hold thel ock‐
ing mechanism on slider 9. #
Pull ring 8 ofthes lider down and simultane‐
ously mo vethes lider away from thel oad. #
Loosen belt strap 5and at thes ame time
mak esuret hat thel oad does no tfall out of
th eb elt stra ps. #
Remo vethel oad from theb elt stra ps.
Installing cargo tie down rings Tr
ansporting 171

#
Turn ther ing of carg otie-down ring B unti lit
is pa rallel tothel ongitudinal axis of cargo tie-
down ring C. #
Holdcargo tie-down ring C between the
inde xfinger an dmiddlefinger an dplace your
th umb thro ugh ther ing of carg otie-down ring
B and ont othe centra lpressur epoint. #
Use your thumb topush thel ocking pin down
as farasitw illg o. #
Push cargo tie-down ring C nea rthe load
th ro ugh then otch es on rack rail2 and mo ve
it appr oximately 0.5 in (1 2mm). #
Remo veyour thumb from thep ressur epoint
and slide cargo tie-down ring C unti lit
engages. #
Turn ther ing of carg otie-down ring B unti lit
is pe rpendicular tothel ongitudinal axis of
cargo tie-down ring C.
Cargo tie-down ring C is secu red.
Re moving cargo tie down rings #
Turn ther ing of carg otie-down ring B unti lit
is pa rallel tothel ongitudinal axis of cargo tie-
down ring C. #
Grip cargo tie-down ring C as described
ab ove unde rins talling and use your thumb to
push thel ocking pin down as farasitw illg o. #
Slide cargo tie-down ring C and pull it down
and ou tthrough then otch es of rack rail2.
At tachin gthe hea dlashing &
WARNING Risk of inju rydue toincor‐
re ctly secu redl oads
When theh ook sont he head lashing are
attached tother ing soft he sliders, thes lid‐
er sc ould come loose. The load ma ycome
loose, fall down and injur epeople, for
ins tance when they enter or load and unload
th ec argo compartment. #
Onlyattach theh ook sont he head lash‐
ing tother ing soft he cargo tie-down
ri ngs. %
The hoo
kson head lashing 3mayonlybe
attached tother ing sofc argo tie down rings
B. #
Chec kthat thel oad is seated securel y. #
Toattac hthe hea dlashing: tensio nhead
lashing 3at bo thends of load 6and
attac htwo hooks Aoftheh ead lashing to
th er ing sofc argo tie down rings B. Placing
aloa dont he wheel ar ch
Compl ywitht he impor tant sa fety no tesu nder
"No tesonl oading" (/ page72). #
Place theo bject sonw heel ar ch2 and lash
th em using tie-down eyes 1(/ page168).
% Aw
heel archm aybe subjec tedtoal oad of
33 0lb( 150k g). 17 2
Transporting

ASS
YSTP LUSs ervice in terv al display Fu
nction of theA SSYSTP LUSs ervice in terv al
display The ASS
YSTP LUSs ervice inter vald ispla yont he
instrument display prov ides informatio nonthe
re maining time or dis tance be fore then ext
service due date.
Yo uc an hide this service messag ebyusingthe
bac kbutton on thel eft-hand side of thes teering
wheel.
Yo uc an obtain fur ther information concerning
th es ervicing of your vehicle from aqualified spe‐
cialis tworks hop, e.g. an authorized Mercedes-
Benz Center. Displaying
thes ervice du edate On-boa
rdcomputer:
4 Service 5
ASSYSTP LUS
The next service due dat eisdisplayed. #
Toexitth ed ispla y:press theb ackb utton on
th el eft-hand side of thes teering wheel.
Bear in mind thef ollowing related topic:
R Operating theo n-boar dcom‐
puter(/ page159) Car
rying out maintenance workregular ly *
NO
TEPrematur ewear thro ugh failur eto
obser veservice due dates Service
workwhic hisn otcar ried out at the
ri ght time or incomple tely can lea dto
inc reased wear and damag etothevehicle. #
Alwayso bser vethep rescribed service
inter vals. #
Alwaysh ave thep rescribed service
wo rkcar ried out at aqualified specialist
wo rkshop. Special service
requ irements The prescribed service inter
valisb ased on nor‐
mal vehicle use. Maintenance workwill need to
be per form ed mor eoften than presc ribed if the
ve hicle is operated under arduous conditions or
increased loads.
Examples of arduous operating conditions:
R regular city driving wit hfrequ ent intermediate
st ops R
mainly short-dis tance driving
R frequent ope ratio ninm ountainou sterrain or
on poor road sur faces
R whe nthe engine is of tenl eftidling forl ong
periods
R operation in particula rlyd usty conditions
and/o rifair-reci rculation mod eisfrequently
used
In these or similar operating conditions, ha vethe
interior air filter ,engin eair cleaner ,engin eoil and
oil filter etc. changed mor efrequ ently .Ifthevehi‐
cle is subjected tohigher loads, thet ires mus tbe
ch eckedm oref requ entl y.Fu rther information can
be obtained at aqualified specialis tworks hop. Batter
ydisconnection periods The ASS
YSTP LUSs ervice in terv al displa ycan
onl ycalculat ethe servic edue date when the
batter yisconnected. #
Notedown thes ervice due dat edispla yedon
th eI nstrument Displa ybefor edisconnecting
th eb atter y(/pag e173). Engine compartment
Opening and closing
theh ood &
WARNING Risk of accident if thee ngine
hood is unlatched while driving
An unloc kede ngin ehood ma yopen up when
th ev ehicle is in motion and bloc kyour vie w. #
Neveru nlatc hthe engine hood while
driving. #
Befor eevery trip, ensur ethat thee ngine
hood is latched. &
WARNING Danger of bu rnsw hen open‐
ing theh ood
If yo uo pen theh ood when thee ngine has
ove rheated or during afireint he engine com‐
partment, youc oul dc om eintoc ontact wi th
ho tg ases or other escaping operating fluids. #
Befor eopening theh ood, allo wthe
engine tocool down. #
Inthee vent of afireint he engine com‐
partment, keep theh ood closed and call
th ef ires ervice. Maintenance and care
17 3

&
WARNING Risk of inju rydue tomoving
parts
Cer tainc omponents in thee ngine compart‐
ment ma ycontinue tomo veor suddenly
mo veagain even af tert he ignition has been
switched off, e.g. thec ooler fan.
Ma kesur eoft hefollowing befor eperform ing
ta sk sint he engine compartment: #
Switc hthe ignition off. #
Nevertouc hthe danger zone sur round‐
ing movin gcomponent parts ,e.g.t he
ro tatio na reaoft hefan. #
Remo vejewe lrya nd watches. #
Keep items of clo thing and hair away
from moving parts. &
WARNING Risk of inju ryfrom touching
component parts unde rvoltage
The ignition sy stem and thef uel injection sys‐
te mw orku nde rhigh voltage. If yout ouch
component parts whic hareunde rvoltage,
yo uc oul drecei vean electric shoc k. #
Nevertouc hcomponent parts of the
ignition sy stem or thef uel injection sys‐
te mw hen thei gnition is switched on. Liv
ec omponents of thef uel injection sy stem
include thei njec tors,for example.
Liv ec omponent softhe ignition sy stem include
th ef ollowing:
R Ignition coils
R Spar kplug connec tors
R Diagnostic soc ket &
WARNING Risk of bu rnsf romh otcom‐
ponent parts in thee ngine compartment
Cer tainc omponents in thee ngine compart‐
ment can be very hot, e.g. thee ngine, the
ra diator and parts of thee xhau stsystem. #
Allo wthe engine tocool down and only
to uc hc omponent parts desc ribed in the
fo llowing. If
yo uh ave tocar ryout an yworkint he engine
compartment, touc ho nlyt he following compo‐
nents:
R Hood
R Engine oil filler openin gcap
R Washer fluid reser voir cap R
Coolant expansion reser voir cap &
WARNING Risk of inju ryfrom using the
windshield wiper swhile thee ngine hood
is open
When thee ngine hood is open and thew ind‐
shield wiper saresetinm otion, youc an be
trapped bythew iper linkage. #
Alwayss witc hoffthew indshield wipers
and ignition befor eopening thee ngine
hood. #
Park thev ehicle in asafel ocation and on a
le ve ls urface if possible. #
Switc hoffthee ngine. #
Secur ethe vehicle agains trolling away. &
WARNING Risk of inju rywhen theh ood
is opened
When youo pen theh ood, it ma ysuddenly
drop int othe end position.
Ther eisar isk of injur yfor an yone in the
hood's rang eofm ovement. #
Befor ereleasing theh ood, ensur ethat
th es uppor tisfirmlyseatedint he
holder. #
Open theh ood onl ywhen ther eisn o-
one in theh ood's rang eofm ovement. #
Toopen: pull handle 1torelease theh ood. #
Reachi ntot he gapa nd push theh ood catch
handle upwards. #
Open theh ood and hold it up. 174
Maintenance and care

#
Take support 1from theb rack et on the
hood and pull it down wards. #
Inse rtthes uppor tint ob rack et below 2. &
WARNING Risk offire due toflammable
material in thee ngine compartmen tor
th ee xhau stsystem
Clo thsoro ther flammable materials lef tin
th ee ngine compartmen tbymista ke could
igni teupon coming int ocontact wi thhots ec‐
tions of thee ngine or exhaus tsyst em. #
Ensur ethat ther ea reno flammable
ex tern al materials in thee ngine com‐
partmen torontheexhaus tsyst em af ter
maintenance workhas been conducted. &
WARNING Risk of accident and inju ry
when opening and closing thee ngine
hood
When opening or closing thee ngine hood, it
ma ysuddenl ydropi ntot he end position.
Ther eisar isk of injur yfor an yone in the
engine hood's rang eofm ovement. #
Only open or close thee ngine hood
when ther ea reno persons in thee ngine
hood's rang eofm ovement. *
NO
TEDama getotheh ood Pushing
theh ood closed wit hyour hands
could dama geit. #
Toclos ethe hood, le titdropf romt he
specified height. #
Toclose: liftt he hood slightl y. #
Movesupport 1totheb rack et on theh ood
and apply light pressur etoengageit. #
Lowe rthe hood and le titdropf romah eight
of appr oximately 0.5 ft(15c m). #
If it is still possible toliftt he hood alittle,
open theh ood again and le titdropf roma
height of appr oximately 0.7 ft(20 cm) until it
engages cor rectly. Engin
eoil Che
cking thee ngine oil le velw ithad ipst ick &
WARNING Risk of bu rnsf romh otcom‐
ponent parts in thee ngine compartment
Cer tainc omponent pa rtsint he engine com‐
partment can be very hot, e.g. thee ngine, the
cooler and pa rtsoft heexhaus tsystem. #
Letthe engine cool down and only
to uc ht he component parts described
as follo ws. Depending on
thee ngine, thed ipstic kmaybe in
va rying locations in thee ngine compartment.
Wa itin gtimeb efor echecking theo il le vel:
R engin eatn ormal operatin gtemperature:
fi ve minutes
R engine no tatnormal operating temp erature
(the engine waso nlys tarted briefly ,for exam‐
ple): 30 minutes Dip
stick( example) #
Park thev ehicle on an even sur face. #
Remo vedipstick 1and wipe it off. Maintenanc
eand care 175

#
Slowly inse rtdipstick 1intot he dipstick
guide tube as farasitw illgoa nd pullito ut
af te rt hree seconds.
R Oil le velO K:theo il le velisb etwe en the
MIN and theM AX mar k.
R Oil le veltoo low: theo il le velisatt he MIN
mar korb elow. #
Ifth eo il le velist oo lo w,add appr ox.
1. 1USq t(1l iter) engine oil. #
Ifth eo il le velist oo high, drain of fexcess
engine oil.
Vi sit aq ualified specialis tworks hop.
Checking thee ngine oil le velw ithano n-
boar dcomputer
Re quirements:
R The vehicle is le veld uring them easuring
process.
R The hood is no topen.
R Dependin gonthe driving profile, theo il le vel
can be displa yedo nlya fter ad riving time of
up to30 minutes and only when thei gnition
is switched on.
On-boar dcomputer:
4 Service 5
Engine Oil Level
Yo uw ills ee one of thef ollowing messa gesin
th em ultifunction displa y: #
Measuring Engine Oil Level...:m easurement
of theo il le veln ot ye tpossible. Repeat the
qu erya fter drivin gamaximu mof30m inutes. #
Engine Oil Level OK andtheb arto displa ythe
oil le velint he multifunction displa yisgreen
and lies between "MIN" and "MAX": theo il
le ve lisO K. #
Engine Oil Level Drive until the engin eis
warm. :warmupt he engine tooperating tem‐
perature. #
Engine Oil Level Correct Measurement Only
if Vehicl eIsonL evel Ground:p arkt he vehicle
on an evensurface. #
Engin eOil Level Add 1,0 liq.gal. andtheb ar
to displa ythe oil le velint he multifunction dis‐
pla yiso rang ea nd lies belo w"MIN": add
1. 1USq t(1l)ofe ngine oil. #
Reduce Engine Oil Level andtheb ar display‐
ing theo il le velint he multifunction displa yis
orang eand lies abo ve"MAX": drain of fexcess
engine oil.
Vi sit aq ualified specialis tworks hop. #
For Engine Oil Level Switch Ignition On :
switc hont he ignition in order tocheckt he
engine oil le vel. #
Engine Oil Level System Inoperative:s ensor is
defectiv eornotconnec ted. Visit aq ualified
specialis tworks hop. #
Engine Oil Level System Currently Unavaila-
ble:c losetheh ood.
% Ve
hicles wit hcold oil le veld ispla ys:the oil
le ve lisa utomaticall ydispla yedont he multi‐
function displa yafter thev ehicle has been
non-operational forane xtende dperiod .Ifit
is no tpossible tomeasu rethee ngine oil
le ve l,ar ele vant messa gewill appear.
Ad ding engin eoil &
WARNING Risk of bu rnsf romh otcom‐
ponent parts in thee ngine compartment
Cer tainc omponents in thee ngine compart‐
ment can be very hot, e.g. thee ngine, the
ra diator and parts of thee xhau stsystem. #
Allo wthe engine tocool down and only
to uc hc omponent parts desc ribed in the
fo llowing. &
WARNING Danger of bu rnsw hen open‐
ing theh ood
If yo uo pen theh ood when thee ngine has
ove rheated or during afireint he engine com‐
partment, youc oul dc om eintoc ontact wi th
ho tg ases or other escaping operating fluids. #
Befor eopening theh ood, allo wthe
engine tocool down. #
Inthee vent of afireint he engine com‐
partment, keep theh ood closed and call
th ef ires ervice. If
yo uh ave tocar ryout an yworkint he engine
compartment, touc ho nlyt he following compo‐
nents:
R Hood
R Engine oil filler openin gcap
R Washer fluid reser voir cap
R Coolant expansion reser voir cap 176
Maintenance and care