2019 MERCEDES-BENZ SPRINTER warning

#
Place the jack toone side. #
Pull thero d with the smallest diame ter off the
pump le ver.
The shor tened pu mpleve r ser ves as a lug
wrench extension. #
Starting with the middle rod, slide the lug
wrench extension as far as it will go onto the
lug wrench. #
Tighten the wheel bolts or nuts evenly in the
sequence indicated (1 to6 ).
Specified tightening torque:
R Steel wheel bolts: 177 lb-ft (240 Nm)
R Wheel nuts: 133 lb-f t(180 Nm)
R Alloy wheel bolts: 133 lb-f t(180 Nm) #
Push the pis ton on thehy draulic jack in again
and close the pressure release scr ew. #
Vehicles with all-wheel drive: turnthe jack
spindle clockwise as far as it will go.
% Yo
u can now ins tallth e hub caps on steel
wheels with wheel bolts. The ins tallation pro‐
cedure depends on whe ther the hub cap acts
as a trim that co vers the whole wheel, or just
co vers the center. #
Wheel with hub cap: position the opening for
th e tire valve in the hub cap overth e tire
va lve. #
Push the edge of the hub cap onto the wheel
ri m with bo thhands until it engages into
place. Make sure the hub cap retaining
cat ches engage on thesteel wheel. #
Wheel with central hub cap: positionthe
re taining lugs of the cent ral hub cap overthe
wheel bolts. #
Hitthe middle of the hub cap toengage it on
th e wheel. #
Secure thefa ulty wheel in the spare wheel
brac ket. #
Vehicles with Super Single tires: transport
th e defective rear wheel in the load area. The
re ar wheel is too lar geforth e spare wheel
brac ket. #
Check the tire pressure of the newly ins talled
wheel and adjust it if necessar y. #
Retighten the wheel bolts or wheel nuts tothe
specified tightening torque af terth eve hicle
has been driven 31miles (50 km). #
When using a wheel or spare wheel with a
new or newly painted wheel rim, ha vethe
wheel bolts or nuts retightened af ter appro x‐
ima tely 620 miles (1,000 km) to3,10 0 miles
(5,000 km).
% Ve
hicles with the tire pressure monitor
sy stem: all ins talled wheels must be equip‐
ped with functioning sensors.
Make sure toobser vethefo llowing fur ther rela‐
te d subject:
R Notes on tire pressure (/ page 234) Spare wheel
Note
s onthe spa rewheel &
WARNING Risk of accident caused by
incor rect wheel and tire dimensions
Wheel and tire dimensions as well as the type
of tire may vary between the spare wheel and
th e wheel tobe replaced. When the spare
wheel is ins talled, driving characteristics may
be se verely af fected.
To prev ent hazardous situations: #
Adapt your driving style according lyand
drive carefull y. #
Never ins tall more than one spare wheel
th at dif fers from the wheel tobe
re placed. #
Only use the spare wheel that dif fers
from the wheel tobe replaced for a
short time. #
Do not switch off ESP ®
. #
Have the spare wheel of a dif fere nt size
re placed at the nearest qualified spe‐
cialist workshop. The wheel and tire Wheels and tires
255

must ha
vethe cor rect dimensions and
th e tire must be the cor rect type. Do not
exceed a maximum speed of 50 mph
(80 km/h) if a spare wheel of a dif fere nt size is
ins talled. &
WARNING Risk of accident from dam‐
aged spa rewheel with Super Sin gle tires
Ve hicles with Super Single tires
The tire of the spare wheel exposed toabo ve-
ave rage loads af ter being ins talled on there ar
axle. If youexc eed the maximum speed or the
maximum dis tance, or ins tallth e spare wheel
again, the tire of the spare wheel may be
damaged. The tire damage may not be visible
and not de tectable.
A damaged tire may cause a loss of tire pres‐
sure. This could cause youto lose control of
th eve hicle. #
Only use the spare wheel if it has not
ye t been ins talled on there ar axle with
th e cur rent tires. #
Ifth e spare wheel had been ins talled on
th ere ar axle, ha vethe tire of the spare
wheel replaced af terch anging the
wheel again, ir respective of the dis‐
ta nce. #
For saf etyre asons, when changing a tire
ensure that only the tire valve type
appr ovedfo rth e tires is used. *
NO
TEDama getothe transmission Ve
hicles with Super Single tires: whenyou
ins tallth e spare wheel on there ar axle, the
transmission may be dama gedby the dif fer‐
ent rotational speeds of the wheels. #
When the spare wheel is ins talled on the
re ar axle, obse rveth e maximum speed
of 34 mph (55 km/h) and the maximum
driving dis tance of 62 miles (100 km). %
The spa
rewheel can be used without restric‐
tions on the front axle of a vehicle with Super
Single tires.
Re gular lych eck that the spare wheel is secured
and has the specified tire pressure
(/ page 234). Re
gularly check thefo llowing, particularly prior to
long trips:
R the tire pressure of the spare wheel (if neces‐
sar y,adjust the tire pressure).
R thefast enings of the spare wheel brac ket.
Re place the tires af ter six years at the latest,
re ga rdless of wear. This also applies tothe spare
wheel.
% If
yo u ha veinstalled a spare wheel, the tire
pressure monitoring sy stem will not function
fo rth is wheel. The spare wheel is not equip‐
ped with a sensor forth e tire pressure moni‐
to ring sy stem. Installing/removing
the spa rewheel Ve
hicles with rear wheel drive: removing the
spare wheel (Cargo Van/Passenger Van) Bolt co
vers forth e saf ety hoo ks(exa mp le: Cargo
Va n) #
Open there ar-end doors. 256
Wheels and tires

Information on
technical data
The given data only applies tovehicles with
st andard equipment. Further information can be
obtained at a qualified specialist workshop. On-board electronics
Note
s onworkon the engine electronics *
NO
TES Premature wearthro ugh
improper main tenance Improper maintenance may cause
vehicle
components towe ar more quickly and the
ve hicle's operating permit may be in validated. #
Always ha vewo rkon the engine elec‐
tronics and related components car ried
out at a qualified specialist workshop. Tw
o-w ayradios In
stallation no tesfo r two-w ayradios &
WARNING Risk of accident due to
improper workon two-w ayradios
The electromagnetic radiation from two-w ay
ra dios can inter fere with the on-board elec‐
tronics if RF transmit ters are manipulated or
re trofitted inco rrectl y.
This could jeopardize the operating saf ety of
th eve hicle. #
You should ha veall workon electrical
and electronic components car ried out
at a qualified specialist workshop. &
WARNING Risk of accident from incor‐
re ct ope ration of two-w ayradios
If yo u operate two- wayra dios incor rectly in
th eve hicle, the electromagnetic radiation
could inter fere with the on-board electronics,
e.g.:
R ifth e two-w ayradio is not connected to
an exterior antenna
R ifth eex terior antenna is not cor rectly
mounted or is not of low reflection
This could jeopardies the operating saf ety of
th eve hicle. #
Have the lo w-reflection exterior antenna
ins talled at a qualified specialist work‐
shop. #
When operating two-w ayradios in the
ve hicle, alw ays connect them tothe
lo w- reflection exterior antenna. *
NO
TEInva lidation of the operating per‐
mit due tofailure tocomply wi th the
instructions for ins tallation and use The operating permit may be in
validated if the
instructions for ins tallation and use of two-
wa yra dios are not obser ved. #
Only use appr oved frequency bands. #
Obser vethe maximum permissible out‐
put po wer in these frequency bands. #
Only use appr oved antenna positions. Use
Tech nical Specification ISO/TS 21609 (Road
Ve hicles - EMC guidelines for ins tallation of af ter‐
mar ketra dio frequency transmitting equipment)
when retrofitting two-w ayradios. Comply with the
legal requirements for de tach able parts.
If yo ur vehicle has ins talling for two-w ayradio
equipment, use the po wer supp lyor antenna con‐
nections intended for use with the ins talling.
Obser vethe manufacturer's supplement during
ins tallation.
Information on two-w ayradio transmission
output
The maximum transmission outputs (PEAK) at the
base of the antenna must not exceed theva lues
in thefo llowing table:
Fr equency band and maximum transmission
output Fr
equency band Maximum transmis‐
sion output
Sho rtwa ve
3 — 54MHz 10
0 W
4 — m — waveband
74 — 88 MHz 30 W
2 — m — waveband
14 4 — 174 MHz 50 W
Tr unked radio sys‐
te m/T etra
380 — 460 MHz 10 W260
Tech nical da ta

Engine number
The engine number is
stamped onto the crank‐
case. You can obtain fur ther information from any
qu alified specialist workshop. Operating fluids and capacities
Note
s on operating fluids &
WARNING Risk of inju ryfrom operating
fl uids harmful to your health
Operating fluids may be poisonous and harm‐
ful to yo ur health. #
Obse rveth ete xt on the original contain‐
ers when using, storing or disposing of
operating fluids. #
Alwaysst ore operating fluids sealed in
th eir original containers. #
Alwayske ep children away from operat‐
ing fluids. +
ENVIRONMEN
TALNO TEEnvironmental
pollution due todisposing of operating
fl uids in a non-environmen tally responsi‐
ble manner Operating
fluids include thefo llowing:
R fuels
R exhaust gas af tertre atment additives, e.g.
DEF
R lubricants
Incor rect disposal of ope rating fluids can
cause considerable damage tothe environ‐
ment. #
Dispose of operating fluids in an envi‐
ro nmentally responsible manner. Operating
fluids include thefo llowing:
R fuels
R exhaust gas af tertre atment additives, e.g.
DEF
R lubricants
R coolant
R brake fluid
R windshield washer fluid
R climate control sy stem refrigerants
Use only products recommended byMercedes-
Benz. Damage caused bythe use of products that ha
ve not been appr oved is not co veredby the
Mercedes-Benz guarantee or goodwill gestures.
Yo u can identify operating fluids appr ovedby
Mercedes-Benz bythefo llowing insc ript ions on
th e container:
R MB-F reigabe (e.g. MB- Freigabe 229. 51 )
R MB-Appr oval (e.g. MB-App rova l 229.51)
Fu rther information on appr oved operating fluids:
R inthe MB Specifications for operating fluids
at http://be vo.mercedes-benz.com (by enter‐
ing the designation)
R at a qualified specialist workshop &
WARNING Risk offire or explosion from
fuel
Fu els are highly flammable. #
Fire, open flames, smoking and creation
of spar ksmust be avoided. #
Swit choff the ignition and, if available,
th est ationary heater, before and while
re fueling theve hicle. &
WARNING Risk of inju ryfrom fuels
Fu els are poisonous and hazardous to your
health. #
Do not swallow fuel or let it come into
contact wi thskin, eyes or clo thing. #
Do not inhale fuel vapor. #
Keep children away from fuel. #
Keep doors and windo wsclosed du ring
th ere fueling process.
If yo u or other people come into contact with
fuel, obser vethefo llowing: #
Immediately rinse fuel off your skin with
soap and water. #
If fuel comes into contact with your
ey es, immediately rinse them thor‐
oughly with clean water.Seek medical
attention immediately. #
Ifyo u swallow fuel, seek medical atten‐
tion immediatel y.Do not induce vomit‐
ing. #
Change immediately out of clo thing that
has come into con tact wi thfuel. Te
ch nical da ta263

Fu
el Note
s on fuel grades on vehicles with a gaso‐
line engine
Obser vethe no tes on operating fluids
(/ page 263).
* NO
TEDo not use diesel torefuel vehicles
with a gasoline engine. If
yo u acciden tally refuel with the wrong fuel:
R Do not switch on the ignition. Otherwise
fuel can enter the engine.
Even small amounts of the wrong fuel
could result in damage tothe fuel sy stem
and the engine. The repair costs are high. #
Contact a qualified specialist workshop. #
Have the fuel tank and fuel lines drained
comple tely. Only
refuel using lo w-sulfur regular fuel with at
least 87AKI/91 RON.
% E10 fuel contains an additive of up
to10%
et hanol. Your vehicle is suitable for use with
E10 fuel. You can fuel your vehicle with E10
fuel.
* NO
TEDama gecaused bythe wrong fuel Even small amounts of
the wrong fuel could
re sult in damage tothe fuel sy stem, engine
and exhaust sy stem. #
Only refuel with there commended fuel. *
NO
TEDama gecaused bythe wrong fuel Even small amounts of
the wrong fuel could
re sult in damage tothe fuel sy stem, engine
and exhaust sy stem.
Ne verre fuel with thefo llowing:
R Diesel
R Gasoline with more than 10%ethanol by
vo lume, e.g. E15, E20, E85, E100
R Gasoline with more than 3% me thanol by
vo lume, e.g. M15, M30, M85, M100
R Gasoline with additives con taining me tal #
Do not mix su chfuels with the fuel rec‐
ommended foryo ur vehicle. %
To
ensure the long evity and per form ance of
th e engine, only unleaded regular gasoline
may be used. No
tethat the higher quality premium grade
ga soline can be refueled at any time.
If yo u are using drums or canis ters to refuel the
ve hicle, you should filter the fuel before filling.
This will pr event malfunctions in the fuel sy stem
due tocontaminated fuel.
Usually you will find information about the fuel
grade on the fuel pump. If there is no identifica‐
tion on the fuel pump, consult a gasst ation
attendant.
% Fo
r fur ther information, contact a qualified
specialist workshop or visit http://
www.mbusa.com (USA only).
Note s on additives in gasoline
Obser vethe no tes on operating fluids
(/ page 263).
* NO
TEDama gefrom use of unsuitable
additives Even small amounts of
the wrong additive
may lead tomalfunctions. #
Only add cleaning additives recommen‐
ded byMercedes-Benzto the fuel. Mercedes-Benz
recommends using brand-name
fuels wi thadditives.
In some countries, theav ailable fuel may not con‐
ta in suf ficient amounts of additi ves. Deposits
could build up in the fuel injection sy stem as a
re sult.
In this case, in consultation with an authorized
Mercedes-Benz Center, the fuel should be mixed
with the cleaning additive recommended by
Mercedes-Benz.
Yo u must obse rveth e no tes and mixing ratios
indica ted on the container.
Note s on fuel grades on vehicles with diesel
engines
Gene ral no tes
Obser vethe no tes on operating fluids
(/ page 263). &
WARNING Risk offire from fuel mixture
If yo u mix diesel fuel with gasoline, theflash
point of the fuel mixture is lo werth an that of
pure diesel fuel.
While the engine is running, component pa rts
in theex haust sy stem may overheat without
wa rning. 264
Tech nical da ta

#
Neverre fuel using gasoline in diesel
engines. #
Never mix gasoline with diesel fuel. *
NO
TEDama gedue toincor rect fuel Even small amounts of
the wrong fuel could
re sult in damage tothe fuel sy stem, the
engine and emission cont rol sy stem.
Ne verre fuel with:
R Gasoline
R Marine diesel
R Heating oil
R Pure bio-diesel or vege tab le oil
R Paraffin or kerosene #
Do not mix such fuels with diesel fuel
and do not use any special additives.
If yo u ha veaccidentally refueled with the
wrong fuel, obser vethefo llowing: #
Do not switch on the ignition. #
Consult a qualified specialist workshop. *
NO
TEMalfunctions due tocontaminated
fuel Fu
el contamination can lead tomalfunctions
in the fuel sy stem. #
Ifyo u are using drums or canis ters to
re fuel theve hicle, you should filter the
fuel before filling. *
NO
TEDama gedue toincor rect fuel Incor
rect fuel can lead toengine damage. #
Refuel only ULSD or diesel fuel with a
sulfur content of maximum 15ppm. Usually
you will find information about the fuel
grade on the fuel pump. If there is no identifica‐
tion on the fuel pump, consult a gasst ation
attendant.
The fuel grade recommended foryo ur vehicle is
fo und on the instruction label in the fuel filler
fl ap . Note
s on low outside temperatures &
WARNING Risk offire and explosion due
to fuel igniting
If yo u heat fuel sy stem components, e.g. with
a heat gun or open flame, these components
could be damaged.
Fu el may leak out and ignite. Depending on
th e type of damage, fuel might not escape
until the engine is running. #
Never heat fuel sy stem components. #
Consult a qualified specialist workshop
to have the malfunction rectified. Re
fill only with commercially available ULTRA-
LO W SULFUR DIESEL (ULSD, maximum sulfur
content 15ppm), which fulfills the ASTM D9 75
st andard.
The flow properties of diesel fuel may be inade‐
qu ate at low outside temp eratures due toparaf fin
separation.
% Malfunctions
resulting from paraf fin separa‐
tion can only be rectified byheating the
entire fuel sy stem. Park theve hicle in a
heated garage ,fo rex ample.
To prev ent malfunctions, diesel fuel with
impr oved flow ch aracteristics is available in the
winter mon ths. Yo u can obtain fur ther informa‐
tion on this at thega sst ation or from your fuel
supplier.
Yo ur vehicle is equipped with a fuel preheating
sy stem. This additionally impr ovesth eflow char‐
acteristics of the diesel fuel byabout 14.5 °F
(8 °C). ULTR A-LO W SULFUR DIESEL can be used
without risk of malfunction down toan outside
te mp erature of appr oximately 14.5 °F (-10 °C).
* NO
TEDama gedue togasoline or paraf fin Gasoline or paraf
fin in diesel fuel impairs the
lubricity of the fuel. This can result in damage
to the fuel injection sy stem, forex ample. #
Do not add any gasoline or paraf fin to
diesel fuel toimpr oveitsflow character‐
istics. B20 fuels with bio-diesel content
* NO
TEDama gedue toincor rect fuel Continuous use of fuels wi
thbio-diesel con‐
te nt ove r 5% (B20 fuels) can lead tofuel filter Te
ch nical da ta265

cases, oil of
the type in the engine is not availa‐
ble, use ano ther appr oved mineral or synthetic
engine oil.
Ve hicles with a diesel engine: ifth e grade is
not available, you may also refill with engine oils
acco rding toMB-F reigabe or MB-Appr oval 228.5,
229.3 or 229.5. The top-up quantity is then limi‐
te dto maximum 1.1 US qt (1.0 liter).
Yo u must then ha vean oil change car ried out at
th e earliest possible opportunit y.
Ve hicles with a gasoline engine: ifth e grade is
not available, you may refill with engine oils
acco rding toMB-F reigabe or MB-Appr oval 229.3
or AC EA A3/B4. The top-up quantity is then limi‐
te dto maximum 1.1 US qt (1.0 liter).
Yo u must then ha vean oil change car ried out at
th e earliest possible opportunit y.
Engine oils are di stinguished by:
R engine oil brand
R grade (MB-F reigabe or MB-Appr oval)
R SAE classi fication (viscosity)
Oil change inter val
The on-board computer automatically sho wsthe
date of the next oil change as an event messa ge
on the displa y.
Mercedes-Benz recommends having the oil
ch anged at a qualified specialist workshop.
Engine oil capacities Engine
Engine oil
M2 74 around11.2 qt
(10.5 li ters)
OM642 around13.2 qt
(12.5 li ters)
OM651 (rear wheel
drive) around
12qt
(1 1. 5 liters) Information on oil consum
ption
Depending on the driving style, theve hicle con‐
sumes a maximum of 1.1 US qt (1.0 liter) of
engine oil per 620 miles (1000 km).
In thefo llowing cases, oil consum ption may also
exc eed this limit:
R theve hicle is ne w.
R you use theve hicle mostly under arduous
conditions.
R you drive frequently at a high engine speed. Re
gular maintenance is a prerequisite forfa vo ra‐
ble consum ption figures. You can on lyassess the
oil consum ption af ter a long journe y.Check the
oil le vel in the engine regularly, e.g. weekly or
ev ery time youre fuel. Note
s on brake fluid Obser
vethe no tes on operating fluids
(/ page 263). &
WARNING Risk of an accident due to
va por poc kets form ing in the brake sys‐
tem
The brake fluid con stantly absorbs moisture
from the air. This lo wersthe boiling point of
th e brake fluid. If the boiling point is too lo w,
va por poc kets may form inthe brake sy stem
when the brakes are applied hard.
This causes the braking ef fect to be impaired. #
Have the brake fluid rene we d at the
specified inter vals. *
NO
TEDama getopaint, plastic or rubber
by brake fluid There is a
risk of damage toproperty if brake
fl uid comes into con tact wi thpaint, plastic or
ru bber. #
If paint, plastic or rubber comes into
con tact wi thbrake fluid, rinse wi th
wate r immediatel y. Obser
vethe no tes on paintwork/matte finish
paintwork care (/ page 211).
Ha ve the brake fluid replaced regular lyat a quali‐
fi ed specialist workshop.
Only use brake fluid appr ovedby Mercedes-Benz
in accordance with MB-F reigabe or MB-Appr oval
33 1.0.
Fu rther information on brake fluid:
R inthe MB Specifications for operating fluids
at http://be vo.mercedes-benz.com
R at a qualified specialist workshop Coolant
Note
s on coolant
Obser vethe no tes on operating fluids
(/ page 263). Te
ch nical da ta269

&
WARNING ‑ Risk of fire and injury from
antifreeze
If antifreeze comes into con tact wi thhot com‐
ponent parts in the engine compartment, it
may ignite. #
Allow the engine tocool down before
adding antif reeze. #
Make sure that no antifreeze spills out
next tothefiller opening. #
Thoroughly clean off any antifreeze from
component parts before starting the
ve hicle. *
NO
TEDama gecaused byincor rect cool‐
ant #
Only add coolant that has been pre‐
mixed with therequ ired antifreeze pro‐
te ction. Information on coolant is
available at thefo llow‐
ing locations:
R inthe MB Specifications for operating fluids
31 0.1
- at http://be vo.mercedes-benz.com
- inthe BeVo app
R at a qualified specialist workshop
* NO
TEOverheating at high outside tem‐
peratures If an inapp
ropriate coolant is used, the engine
cooling sy stem is not suf ficiently pr otected
against overheating and cor rosion at high out‐
side temp eratures. #
Always use a coolant appr ovedby
Mercedes-Benz. #
Obser vethe instructions in the MB
Specifications for operating fluids3 10.1 . *
NO
TEPaint wo rkdamage due tocoolant #
Do not spill coolant on painted sur faces. Ha
ve the coolant regularly replaced at a qualified
specialist workshop.
No tethe proportion of anti-cor rosion agent/anti‐
freeze in the engine cooling sy stem within thefo l‐
lowing temp erature ranges:
R Atleast 50% (antifreeze pr otection up to
about -35 °F (-37 °C)) R
Maximum 55% (antifreeze pr otection up to
-49 °F (-45 °C))
Coolant capacities
Engine cooling sy stem Engine
Coolant
M2 74 approx. 3.0 gal
(1 1. 5 liters)
OM642 approx. 2.6 gal
(10 liters)
OM65 1a pprox. 2.5 gal
(9.5 liters) Wi
ndshield washer fluid Note
s on windshield washer fluid
Obser vethe no tes on operating fluids
(/ page 263). &
WARNING ‑ Risk of fire and injury from
windshield washer concentrate
Wi ndshield washer concentrate is highly flam‐
mable. It could ignite if it comes into con tact
wi th hot engine component parts or the
ex haust sy stem. #
Make sure that no windshield washer
concentrate spills out next tothefiller
opening. *
NO
TEDama getotheex terior lighting
due tounsuitable windshield washer fluid Uns
uitable windshield washer fluid may dam‐
age the plastic sur face of theex terior lighting. #
Only use windshield washer fluid which
is also suitable for use on plast ic surfa‐
ces, e.g. MB SummerFit or MB Winter‐
Fit. *
NO
TEBlocked spr aynozzles caused by
mixing windshield washer fluids #
Do not mix MB SummerFit and MB Win‐
te rFit with other windshield washer flu‐
ids. Do not use distilled or de-ionized
water.Other‐
wise, the le vel sensor may give a false reading. 270
Tech nical da ta