2019 MAZDA MODEL CX-30 manual transmission

xThe shift lever/selector lever is in a position other than R.

Display switching
The displayed screen can be changed each time the 360°view monitor switch is
pressed.
1. Top view/Front view
2. Top view/Front wide view
3. Side view
4. Home screen
NOTE
xWhen the shift lever/selector lever is in R position, the displayed screen does not
switch to the top view/front view, top view/front wide view, or the side view.
xDisplay of the top view/front view, top view/front wide view, or the side view
stops even with the display conditions met if any of the following conditions
occurs.
xWhen a switch around the commander knob is pressed.x(Manual transmission)
The parking brake is applied.
When Driving
i-ACTIVSENSE
4-193

x(Automatic transmission)
The selector lever is shifted to P position (displayed when the selector lever is in
a position other than P).
x(Displayed when vehicle speed is less than 15 km/h (9.3 mph))
x4 minutes and 30 seconds have passed.xThe vehicle speed is about 15 km/h (9.3 mph) or faster.x(Displayed when the vehicle speed is about 15 km/h (9.3 mph) or faster)
xThe vehicle speed is about 15 km/h (9.3 mph) or faster after 8 seconds have
passed since pressing the 360°View Monitor switch.
xFour minutes and 22 seconds have passed from the point when the vehicle
speed was less than 15 km/h (9.3 mph) after 8 seconds have passed since
pressing the 360°View Monitor switch.
xThe 360°View Monitor settings can be changed as follows.
Refer to the Settings section in the Mazda Connect Owner's Manual.
xAutomatic display of the 360°View Monitor when the ultrasonic senor detects
an obstruction.
xAutomatic display of the 360°View Monitor when the ignition is switched ON.xScreen priority level when the system launches.
Top view/Rear view, Top view/Rear wide view
The top view/rear view, top view/rear wide view displays when all of the following
conditions are met.
xThe ignition is switched ON.xShift lever/selector lever is in R position.
Display switching
The displayed screen can be changed each time the 360°view monitor switch is
pressed.
1. Top view/Rear view
2. Top view/Rear wide view
NOTE
xThe top view/rear view and top view/rear wide view automatically display
whether or not the 360°View Monitor switch is turned on or off when shifting the
shift lever/selector lever to R position.
xThe top view/rear view and top view/rear wide view displays the previously
displayed screen.
When Driving
i-ACTIVSENSE
4-194

Cruise Set Indication (Green)
The indication turns on (green) when a
cruising speed has been set.
▼Activation/Deactivation
WARNING
Always turn off the cruise control
system when it is not in use:
Leaving the cruise control system in an
activation-ready state while the cruise
control is not in use is dangerous as the
cruise control could unexpectedly
activate if the activation button is
accidentally pressed, and result in loss
of vehicle control and an accident.
NOTE
When the ignition is switched OFF, the
system status before it was turned off is
maintained. For example, if the
ignition is switched OFF with the cruise
control system operable, the system
will be operable when the ignition is
switched ON the next time.
Activation
To activate the system, press the cruise
switch. The cruise standby indication
(white) turns on.
Deactivation
To deactivate the system, press the
cruise switch again.
The cruise standby indication (white)
turns
off.
▼To Set Speed
1. Activate the cruise control system
by pressing the cruise switch. The
cruise standby indication (white)
turns on.
2. Accelerate to the desired speed,
which must be more than 25 km/h
(16 mph).
3. Adjust the system to the desired
vehicle speed using the accelerator
pedal. Press the RES switch up (SET
+) or down (SET-) to start cruise
control. The cruise control
indication (green) in the instrument
cluster turns on at the same time.
Quickly release the switch when the
cruise control indication (green)
turns on.
NOTE
xIf the RES switch is operated up (SET
+) or down (SET-) while the vehicle
speed is between 25 km/h (16 mph)
and 30 km/h (19 mph), the set
speed is set to 30 km/h (19 mph).
xThe cruise control speed setting
cannot be performed under the
following conditions:
xAny of the doors is opened.xThe driver's seat belt is unfastened.xThe brake pedal is depressed.xThe parking brake is applied.x(Automatic transmission)
The selector lever is in the P or N
position.
x(Manual transmission)
The shift lever is in the neutral
position.
xOn a steep grade, the vehicle may
momentarily slow down while
ascending or speed up while
descending.
xThe cruise control will cancel if the
vehicle speed decreases below 20
km/h (12 mph) when the cruise
control is activated, such as when
climbing a steep grade.
When Driving
Cruise Control
4-229

30 km/h (19 mph) or more and press
the RES switch.
▼To Te m p o ra r i l y C a n c e l
To temporarily cancel the system, use
one of these methods:
xSlightly depress the brake pedal.xPress the CANCEL switch.x(Manual transmission)
Depress the clutch pedal.
If the RES switch is pressed when the
vehicle speed is 30 km/h (19 mph) or
higher, the system reverts to the
previously set speed.
NOTE
xIf any of the following conditions
occur, the cruise control system is
temporarily cancelled.
xEven when the brake pedal is
slightly depressed.
xThe DSC is operating.xThere is a problem in the system.xAny of the doors is opened.xThe driver's seat belt is unfastened.xThe parking brake is applied.x(Automatic transmission)
The selector lever is in the P or N
position.
x(Manual transmission)
The shift lever is in the neutral
position.
xWhen the cruise control system is
temporarily cancelled by even one of
the applicable cancel conditions, the
speed cannot be re-set.
x(Automatic transmission)
The cruise control cannot be
cancelled while driving in manual
mode (selector lever shifted from D
to M position). Therefore, engine
braking will not be applied even if
the transmission is shifted down to a
lower gear. If deceleration is
required, lower the set speed or
depress the brake pedal.
▼To D e a c t i va t e
Press the cruise switch again.
When Driving
Cruise Control
4-231

xIf “No camera signal.” is indicated in
the display, there could be a
problem with the camera. Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
x(Predicted vehicle path assist lines
display type)
If force is applied to the steering
wheel, the guide lines may not
display. Loosen your grip on the
steering wheel to allow the guide
lines to display.
▼Rear View Parking Camera
Location
1. Rear view parking camera
▼Switching to the Rear View
Monitor Display
Shift the shift lever (manual
transmission) or the selector lever
(automatic transmission) to reverse (R)
position with the ignition switched ON
to switch the display to the rear view
monitor display.
NOTE
When the shift lever (manual
transmission) or the selector lever
(automatic transmission) is shifted
from reverse (R) position to another
shift lever (manual transmission) or the
selector lever (automatic transmission)
position, the screen returns to the
previous display.
When Driving
Rear View Monitor
4-239

also varies depending on conditions, so confirm the surrounding conditions directly
with your eyes and steer the vehicle in accordance with the conditions.
Be well aware of the above cautions prior to using the rear view monitor.
Predicted vehicle path assist lines display type
NOTE
The following shows an example of vehicle parking in which the steering wheel is
turned to the right when backing up the vehicle. The operation is reversed when
backing up the vehicle from the opposite direction.
1. Shift the shift lever (manual transmission) or the selector lever (automatic
transmission) to reverse (R) position to switch the display to the rear view
monitor display.
2. Before backing the vehicle into the parking space, turn the steering wheel while
referring to the projected vehicle path display so that the vehicle enters the
centre of the parking space.

1. (Display condition)
2. (Vehicle condition)
When Driving
Rear View Monitor
4-243

the vehicle in the best possible position. (If the parking space has division lines,
check whether the vehicle width guide lines are parallel to them.)

1. (Display condition)
2. (Vehicle condition)
6. When the shift lever (manual transmission) or the selector lever (automatic
transmission) is shifted from reverse (R) position to another shift lever (manual
transmission) or the selector lever (automatic transmission) position, the screen
returns to the previous display.
NOTE
Because there may be a difference between the displayed image, such as indicated
below, and the actual conditions when parking , always verify the safety at the rear of
the vehicle and the surrounding area directly with your eyes.
xIn the image of the parking space (or garage) displayed on the screen, the back
end and distance guide lines may appear aligned in the monitor, but they may not
actually be aligned on the ground.
When Driving
Rear View Monitor
4-245

xWhen parking in a space with a division line on only one side of the parking space,
the division line and the vehicle width guide line appear aligned in the monitor,
but they may not actually be aligned on the ground.
Fixed assist lines display type
NOTE
Images displayed on the monitor from the rear view parking camera are reversed
images (mirror images).
1. Shift the shift lever (manual transmission) or the selector lever (automatic
transmission) to reverse (R) position to switch the display to the rear view
monitor display.
When Driving
Rear View Monitor
4-246