2019 MAZDA MODEL CX-30 manual transmission

NOTE
xOnly make calls manually for conditions requiring urgent treatment such as illness
or serious injury.
xWhen making emergency calls manually, stop the vehicle in a safe location before
making the call.
xThe call centre will end an emergency call. The user cannot end the emergency
call.
xIf a call is disconnected or a call cannot be made to the call centre correctly, an
automatic call is made again to the call centre.
1. Make sure that the ignition is switched ON.
2. Long-press the Emergency call switch on the overhead console and then release
your finger from the switch.
1. Emergency call switch
3. The indicator light (green) on the Emergency call switch
flashes slowly (0.5
second intervals) and the call is made to the call centre.
1. Green
4. When the connection is established with the call centre, the indicator light
(green)
flashes somewhat quickly (0.3 second intervals) and the transmission of
the vehicle information begins.
5. When the transmission of the vehicle information is completed or about 20
seconds have elapsed since the transmission began, the beep sounds and the
voice call with the call centre starts.
If Trouble Arises
Emergency Call System
7-9

CAUTION
¾Do not disassemble the Mazda ERA-GLONASS. Otherwise, it could become
damaged and may not function in an emergency.
¾The Mazda ERA-GLONASS has a special built-in battery so that it can operate even
if the power supply from the vehicle is cut such as in an accident.
Heed the following cautions. If the Mazda ERA-GLONASS is not used correctly it
may not operate.
¾The built-in battery is not a rechargeable type battery. Do not attempt to
recharge the battery.
¾The built-in battery life is 3 years. Have the built-in battery replaced at an
Authorised Mazda Repairer periodically.
¾If the built-in battery power is low due to natural discharge and the system
determines that there is a problem, the Mazda ERA-GLONASS cannot be used.
If the system determines that there is a problem, the indicator light (red) in the
Emergency call switch turns on to notify the driver. Have the vehicle inspected at
an Authorised Mazda Repairer. Refer to Indicator light/Beep sound on page
7-19.
NOTE
xThe Mazda ERA-GLONASS can be used when the ignition is switched ON.xThere are two ways the Mazda ERA-GLONASS makes calls; automatically or
manually.
xThe Mazda ERA-GLONASS may not make a connection under the following
conditions or depending on the use environment. If the Mazda ERA-GLONASS
does not connect, make a call from another telephone such as the nearest
available public telephone.
xThe vehicle is outside of a mobile phone network areaxThe vehicle is in a weak radio wave transmission environment (such as inside
tunnels, underground parking areas, shadow of buildings, and mountain areas)
xThe vehicle does not receive an impact of a certain level or more even if an
accident has occurred.
xAn extremely serious collision occurs resulting in damage to the Mazda
ERA-GLONASS.
xThe position information cannot be obtained when signals cannot be received
from the GNSS satellites, however, voice calls are possible.
xWhen a voice call is made by the Mazda ERA-GLONASS, the audio system is
muted so that it does not interfere with the call.
xIt may take some time for the call centre to respond after the Mazda
ERA-GLONASS
first starts operating.
xIf you are unable to respond to an operator's questions after the voice call begins,
the operator may proceed with emergency procedures at their own discretion.
xEven if it is
difficult for you to hear the operator's voice, your voice may be heard
by the call centre. Continue explaining your circumstances.
If Trouble Arises
Mazda
ERA-GLONASS
7-15

2. The indicator light (green) on the Emergency call switch flashes slowly (0.5
second intervals) and the call is made to the call centre.
1. Green
3. When the connection is established with the call centre, the indicator light
(green) flashes somewhat quickly (0.3 second intervals) and the beep sounds
simultaneously, and the transmission of the vehicle information begins.
4. When the transmission of the vehicle information is completed or about 20
seconds have elapsed since the transmission began, the beep sounds and the
voice call with the call centre starts.
5. If the connection fails, the indicator light (red) turns on and the indicator light
(green) flashes quickly (0.15 second intervals) and the beep sounds
simultaneously.
In this case, make a manual connection using the Emergency call switch because
an automatic connection is not possible.
1. Red (Turns on)
2. Green (Flashes)
Manual emergency calls
With the ignition switched ON, long-press the Emergency call switch and after
releasing your
finger from the switch, the vehicle information is automatically
transmitted to the call centre.
When the transmission of the vehicle information is completed or about 20 seconds
have elapsed since the transmission began, the voice call with the call centre starts.
If Trouble Arises
Mazda
ERA-GLONASS
7-17

NOTE
xOnly make calls manually for conditions requiring urgent treatment such as illness
or serious injury.
xWhen making emergency calls manually, stop the vehicle in a safe location before
making the call.
xThe call centre will end an emergency call. The user cannot end the emergency
call.
xIf a call is disconnected or a call cannot be made to the call centre correctly, an
automatic call is made again to the call centre. To cancel the redialing, refer to
Manual emergency call cancellation.
1. Make sure that the ignition is switched ON.
2. Long-press the Emergency call switch on the overhead console and then release
your finger from the switch.
1. Emergency call switch
3. The indicator light (green) on the Emergency call switch flashes slowly (0.5
second intervals) and the call is made to the call centre.
1. Green
4. When the connection is established with the call centre, the indicator light
(green) flashes somewhat quickly (0.3 second intervals) and the beep sounds
simultaneously, and the transmission of the vehicle information begins.
5. When the transmission of the vehicle information is completed or about 20
seconds have elapsed since the transmission began, the beep sounds and the
voice call with the call centre starts.
If Trouble Arises
Mazda
ERA-GLONASS
7-18

¾Tyre sealant that comes into contact
with the eyes and skin is dangerous.
If tyre sealant enters the eyes or
contacts the skin, flush immediately
with large amounts of water and
seek medical assistance.
NOTE
xThe tyre sealant cannot be reused.
Purchase new tyre sealant at an
expert repairer (we recommend an
Authorised Mazda Repairer).
xThe emergency flat tyre repair kit
cannot be used in the following
cases.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe period of
effective use for the
tyre sealant has expired. (The
period of
effectiveness is indicated
on the bottle label.)
xThe tear or puncture exceeds
about 4 mm (0.16 in).
xThe damage has occurred to an
area of the tyre other than the
tread.
xThe vehicle has been driven with
nearly no air remaining in the tyre.
xThe tyre has come off the wheel
rim.
xDamage to the wheel rim has
occurred.
xThe tyre has 2 or more punctures.
▼Using the Emergency Flat Tyre
Repair Kit
1. Park on a level surface off the
right-of-way and set the parking
brake.
2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1,
and turn off the engine.
3. Turn on the hazard warning flasher.
4. Unload passengers and luggage,
and remove the emergency flat tyre
repair kit.
Ty p e A
Ty p e B
Ty p e C
5. Shake the tyre sealant well.

If Trouble Arises
Flat Tyre
7-28

2. Put a vehicle with an automatic
transmission in Park (P), a manual
transmission in Reverse (R) or 1,
and turn off the engine.
3. Turn on the hazard warning flasher.
4. Have passengers get out of the
vehicle and away from the vehicle
and traffic.
5. Remove any luggage, the jack,
tools, and spare tyre (page 7-24).
6. Block the wheel diagonally
opposite the flat tyre. When
blocking a wheel, place a tyre block
both in front and behind the tyre.
NOTE
When blocking a tyre, use rocks or
wood blocks of sufficient size if
possible to hold the tyre in place.
▼Removing a Flat Tyre
WARNING
When jacking-up a vehicle, always
shift the shift lever to 1st or R position
(manual transmission vehicle) or shift
the selector lever to P position
(automatic transmission vehicle),
apply the parking brake, and place
wheel blocks in the position
diagonally opposed to the jack:
Changing a flat tyre without using
wheel blocks is dangerous because the
vehicle may move and fall off the jack
even with the shift lever in 1st or R
position, or the selector lever is in P
position, which could result in an
accident.
1. If your vehicle is equipped with a
wheel cover, pry off the wheel
cover with the bevelled end of the
jack lever.

NOTE
Force the end of the jack lever
firmly between wheel and cover, or
removal will be difficult.
CAUTION
Align the notch on the wheel cover
with the valve stem when installing
it.

1. Notch
If Trouble Arises
Flat Tyre
7-34

Starting a Flooded Engine
(SKYACTIV-G 2.0,
SKYACTIV-G 2.5 and
SKYACTIV-X 2.0)
▼Starting a Flooded Engine
If the engine fails to start, it may be
flooded (excessive fuel in the engine).

Follow this procedure:

1. If the engine does not start within 5
seconds on the first try, wait 10
seconds and try again.
2. Make sure the parking brake is on.
3. Depress the accelerator all the way
and hold it there.
4. Depress the clutch pedal (manual
transmission) or the brake pedal
(automatic transmission), then
press the push button start. If the
engine starts, release the
accelerator immediately because
the engine will suddenly rev up.
5. If the engine fails to start, crank it
without depressing the accelerator.

If the engine still does not start using
the previous procedure, have your
vehicle inspected by an expert repairer
(we recommend an Authorised Mazda
Repairer).
Push-Starting
▼Push-Starting
Do not push-start your Mazda.
WARNING
Never tow a vehicle to start it:
Towing a vehicle to start it is
dangerous. The vehicle being towed
could surge forward when its engine
starts, causing the 2 vehicles to collide.
The occupants could be injured.
CAUTION
Do not push-start a vehicle that has a
manual transmission. It can damage
the emission control system.
NOTE
You cannot start a vehicle with an
automatic transmission by pushing it.
If Trouble Arises
Emergency Starting
7-42

Overheating
▼Overheating
If the engine coolant temperature
gauge indicates overheating and the
high engine coolant temperature
warning indication is displayed, the
vehicle loses power or you hear a loud
knocking or pinging noise, the engine
is probably too hot.
WARNING
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running
indefinitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
Open the bonnet ONLY after steam is
no longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.
If the engine coolant temperature
gauge indicates overheating and the
high engine coolant temperature
warning indication is displayed:

1. Drive safely to the side of the road
and park off the right-of-way.
2. Put a vehicle with an automatic
transmission in park (P), a manual
transmission in neutral.
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine
compartment.

If steam is coming from the engine
compartment:
Do not go near the front of the
vehicle. Stop the engine.
Wait until the steam dissipates,
then open the bonnet and start the
engine.

If neither coolant nor steam is
escaping:
Open the bonnet and idle the
engine until it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the
engine temperature will increase.
Stop the engine and call an expert
repairer (we recommend an
Authorised Mazda Repairer).
6. Make sure the cooling fan is
operating, then turn off the engine
after the temperature has
decreased.
7. When cool, check the coolant level.
If Trouble Arises
Overheating
7-44