2019 MAZDA MODEL CX-30 manual transmission

xThe operation frequency of the braking by the CTS control is high.x(Automatic transmission vehicle)
The parking brake is automatically applied during stop hold control.
x(Manual transmission vehicle)
xThe vehicle speed decreases below 25 km/h (15 mph).xThe shift lever is in the neutral position for a certain period of time.xThe clutch pedal is depressed for a certain period of time.xThe engine has stalled.

Steering assist function
If any of the following conditions occurs, the steering assist function is temporarily
cancelled.
xThe headway control function is cancelled.xWhite (yellow) lane lines cannot be detected or a vehicle ahead cannot be
recognised.
xYour vehicle speed is more than about 60 km/h (37 mph).xThe accelerator pedal is operated.xThe direction indicator lever is operated.xThe vehicle is being driven on a sharp curve.xThe width of a lane is excessively narrow or wide.xThe vehicle crosses a lane line.xThe driver takes his/her hands off the steering wheel.xThe steering wheel is operated abruptly.xThere is a problem with the system.xThe temperature in the Forward Sensing Camera (FSC) is too high or too low.xThe windscreen around the Forward Sensing Camera (FSC) is foggy.xThe windscreen around the Forward Sensing Camera (FSC) is blocked by an
obstruction, causing poor forward visibility.

NOTE
If you take your hands off the steering wheel (not holding the steering wheel), the
warning sound is activated and an alert is indicated on the multi-information display
and the active driving display.
When Driving
i-ACTIVSENSE
4-159

Multi-information display
Active driving display
If the steering wheel is held lightly, or depending on the road conditions, the system
determines that you have released the steering wheel (not holding the steering
wheel) even if you are holding it, and an alert is indicated on the multi-information
display and the active driving display.

To resume operation
If the CTS is temporarily cancelled, it will resume operation at the previously set
speed by pressing the RES switch after all of the operation conditions have been
met.
NOTE
xIf the set speed is not indicated on the display, the system does not operate even if
the RES switch is pressed.
xAfter the operation, the steering assist operation may not operate for a period of 5
seconds at the most until the lane lines are detected or a vehicle ahead is
recognised.

Turning
off
When the CTS switch is pressed while the CTS is operating , the CTS turns off.
▼Shift-up/Shift-down Request
Display (Manual Transmission)
The shift-up or shift-down request
display might be displayed while the
CTS is operating. When this occurs,
shift gears because the gear position is
not appropriate.
When Driving
i-ACTIVSENSE
4-160

xThe accelerator pedal is depressed
abruptly.
xThe brake pedal is being
depressed.
xThe steering wheel is being
operated.
xThe selector lever is being shifted.xThe direction indicator lever is
being operated.
xWhen warnings and messages,
such as a dirty windscreen, related
to the Forward Sensing Camera
(FSC) or front radar sensor are
being displayed on the
multi-information display.
xThe SBS may operate under the
following conditions.
xThere is an object in the road at
the entrance to a curve (including
guardrails and snow banks).
xPassing an approaching vehicle
while rounding a curve.
xWhen crossing a narrow bridge,
and passing through low gates,
narrow gates, car washing
machines, or tunnels.
xWhen passing through a toll gate.xWhen entering an underground
parking area.
xThere is a metal object, bump, or a
protruding object on the road.
xIf you suddenly come close to a
vehicle ahead.
xThere is an animal, wall, or tree.xNotifies the driver with a warning
indication on the multi-information
display and the active driving display
(vehicles with active driving display)
while the system is operating.
xIf a malfunction is detected or the
system temporarily stops the
function due to dirty sensors (such as
radar sensor or Forward Sensing
Camera (FSC)), the i-ACTIVSENSE
warning indication/warning light
turns on and a message is displayed
on the multi-information display.
xOn a manual transmission vehicle,
the engine stops if the clutch pedal is
not depressed when the vehicle is
stopped by the SBS brake operation.
xIf the vehicle is stopped by the SBS
brake operation and the brake pedal
is not depressed, the SBS brake is
automatically released after about 2
seconds.
▼Collision Warning
When there is a possibility of a
collision with a vehicle ahead, the
collision warning sound is activated
continuously and a warning is
displayed on the multi-information
display and the active driving display.
Multi-information display
1. “BRAKE!” message is displayed

Active driving display
When Driving
i-ACTIVSENSE
4-176

xThe SBS-R system will operate under
the following conditions.
xThe engine is running.xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is between
about 2 to 8 km/h (2 to 4 mph).
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions and the
SBS-R may not operate.
xThe height of the obstruction is
low such as low walls or trucks
with low loading platforms.
xThe height of the obstruction is
high such as trucks with high
loading platforms.
xThe obstruction is small.xThe obstruction is thin such as a
signpost.
xThe surface of the obstruction is
not pointed vertically relative to
the vehicle.
xThe obstruction is soft such as a
hanging curtain or snow stuck to a
vehicle.
xThe obstruction is shaped
irregularly.
xThe obstruction is extremely close.xIn the following cases, the rear
ultrasonic sensor and rear camera
cannot detect obstructions correctly
and the
SBS-R may not operate.
xSomething is stuck on the bumper
near a rear ultrasonic sensor.
xThe brake or accelerator pedal is
operated.
xThere is another obstruction near
one obstruction.
xDuring inclement weather such as
rain, fog and snow.
xHigh or low humidity.xHigh or low temperaturesxStrong winds.xThe path of travel is not flat.xHeavy luggage is loaded in the
luggage compartment or on the
rear seat.
xObjects such as a wireless aerial,
fog light, or illuminated number
plate is installed near a rear
ultrasonic sensor.
xThe orientation of a rear ultrasonic
sensor has deviated for reasons
such as a collision.
xThe vehicle is affected by other
sound waves such as the horn,
engine noise, ultrasonic sensor of
another vehicle.
xIn the following cases, a rear
ultrasonic sensor and rear camera
may detect something as a target
obstruction which could cause the
SBS-R system to operate.
xDriving on a steep slope.xWheel blocks.xHanging curtains, gate poles such
as at toll gates and railroad
crossing.
xWhen travelling near objects such
as foliage, barriers, vehicles, walls,
and fences along a road.
xWhen driving off-road in areas
where there is grass and forage.
xWhen passing through low gates,
narrow gates, car washing
machines, and tunnels.
xA trailer is connected.xA bright light source such as
sunlight hits the rear camera.
xThe surroundings are dark.
When Driving
i-ACTIVSENSE
4-179

xAn exterior accessory such as a
bicycle carrier is installed around a
rear ultrasonic sensor.
x(Manual transmission)
If the vehicle is stopped by the SBS-R
operation and the clutch pedal is not
depressed, the engine stops.
xWhen the system operates, the user
is notified by the multi-information
display.
xThe collision warning beep sounds
intermittently while the SBS-R brake
is operating.
xIf the vehicle is stopped by the SBS-R
operation and the brake pedal is not
depressed, displaying in meter
“Emergency Braking Activated.
Depress Brake Pedal to Hold Stop”,
after about 2 seconds and the SBS-R
brake is automatically released.
xIf a Mazda genuine trailer hitch is
used, the SBS-R is automatically
turned off.
xTurn off the SBS-R system while
pulling a trailer or while an accessory
such as a bicycle carrier is installed to
the rear of the vehicle.
▼Collision Warning
If there is a possibility of a collision, the
collision warning sound is activated
continuously and a warning is
displayed on the active driving display
and the multi-information display.
Multi-information display
1. “BRAKE!” message is displayed

Active driving display
1. “BRAKE!” message is displayed
▼Stopping the Smart Brake Support
[Rear] (SBS-R) System Operation
The SBS-R can be changed to
inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS-R is cancelled, the SBS
OFF indicator light turns on.
NOTE
xWhen the ignition is switched OFF
while the SBS-R is cancelled, the
SBS-R is automatically enabled the
next time the ignition is switched
ON.
xWhen the SBS-R is cancelled, the
Smart Brake Support [Rear Crossing]
(SBS-RC) is also cancelled.
When Driving
i-ACTIVSENSE
4-180

Smart Brake Support
[Rear Crossing] (SBS-RC)
*
▼Smart Brake Support [Rear
Crossing]
(SBS-RC)
The SBS-RC is a system designed to
assist the driver in avoiding collisions
and to reduce damage in the event of
a collision by applying the brakes if
there is the possibility of collision with
a vehicle approaching from the rear
while you are reversing out of parking
space.
The SBS-RC system detects vehicles
approaching from the rear left and
right sides of the vehicle, and the rear
of the vehicle while the vehicle is being
reversed out of a parking space, the
system reduces damage in the event of
a collision by operating the brake
control when the system determines
that a collision is unavoidable.
SBS-RC operation
1. The SBS-RC system operates when
the shift lever (manual
transmission) or the selector lever
(automatic transmission) is shifted
to the reverse (R) position.
2. If there is the possibility of a
collision with an approaching
vehicle, the SBS-RC system applies
brake and displays “BRAKE!” on the
active driving display and the
multi-information display.
WARNING
Always check the surrounding area
visually before actually putting the
vehicle in reverse:
The system is only designed to assist
you in backing out of the lot when
putting the vehicle in reverse. Due to
certain limitations with the operation
of this system, the SBS-RC system may
not operate brake or it might be
delayed even though a vehicle is
behind your vehicle. Always make it
your responsibility as a driver to check
the rear.
Do not rely completely on the SBS-RC
system:
¾The
SBS-RC system is only designed
to reduce damage in the event of a
collision. Over reliance on the system
leading to the accelerator pedal or
brake pedal being mistakenly
operated could result in an accident.
¾The SBS-RC system operates in
response to a vehicle. The system
does not operate in response to
obstructions such as a wall,
pedestrians, 2-wheeled vehicles, or
animals.
To assure the correct operation of the
SBS-RC, heed the following cautions.
¾Do not apply a sticker to a rear radar
and rear camera. Otherwise, the rear
radar and rear camera may not be
able to detect vehicles or
obstructions which could result in an
accident.
¾Do not disassemble a rear radar and
rear camera.
When Driving
i-ACTIVSENSE
*Some models.4-181

¾If cracks or damage caused by flying
gravel or debris is visible around a
rear radar and rear camera, stop
using the SBS-RC system
immediately and have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer). If the vehicle continues to
be driven with cracks or scratch
marks left around an ultrasonic
sensor, the system may operate
unnecessarily and cause an
unexpected accident.
Refer to Stopping the Smart Brake
Support [Rear Crossing] (SBS-RC)
System Operation on page 4-184.
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for rear bumper
replacement.
Do not modify the suspension:
If the vehicle height or inclination is
changed, the
SBS-RC system may not
operate correctly because it cannot
detect obstructions correctly.
Do not apply a strong force to a rear
radar and rear camera:
When washing the vehicle, do not
spray highly pressurised water against a
rear radar and rear camera, or rub it
strongly. In addition, do not hit the rear
bumper forcefully when loading and
unloading cargo. Otherwise, the
sensors may not detect obstructions
correctly which could cause the
SBS-RC system to not operate
normally, or it could operate
unnecessarily.
NOTE
xThe SBS-RC system will operate
under the following conditions.
xThe engine is running.
xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is under about
10 km/h (6 mph).
xThe vehicle speed of an
approaching vehicle is about 3
km/h (2 mph) or faster.
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the
i-ACTIVSENSE warning indication/
warning light turns on and operation
of the system is stopped. If the
i-ACTIVSENSE warning indication/
warning light remains illuminated,
have the vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system
including the SBS-RC system.
xA large deviation in the installation
position of a rear side radar sensor
on the vehicle has occurred.
xThere is a large accumulation of
snow or ice on the rear bumper
near a rear side radar sensor.
xDriving on snow-covered roads for
long periods.
xThe temperature near the radar
sensors becomes extremely hot
due to driving for long periods on
slopes during the summer.
xThe battery voltage has decreased.xUnder the following conditions, the
rear side radar sensor cannot detect
target objects or it may be difficult to
detect them.
When Driving
i-ACTIVSENSE
4-182

x(Manual transmission)
If the vehicle is stopped by the
SBS-RC operation and the clutch
pedal is not depressed, the engine
stops.
xWhen the system operates, the user
is notified by the multi-information
display.
xThe collision warning beep sounds
intermittently while the SBS-RC
brake is operating.
xIf the vehicle is stopped by the
SBS-RC operation and the brake
pedal is not depressed, displaying in
meter “Emergency Braking Activated.
Depress Brake Pedal to Hold Stop”,
after about 2 seconds and the
SBS-RC brake is automatically
released.
xIf a Mazda genuine trailer hitch is
used, the SBS-RC is automatically
turned off.
▼Collision Warning
If there is a possibility of a collision, the
collision warning sound is activated
continuously and a warning is
displayed on the active driving display
and the multi-information display.
Multi-information display
1. “BRAKE!” message is displayed

Active driving display
1. “BRAKE!” message is displayed
▼Stopping the Smart Brake Support
[Rear Crossing]
(SBS-RC) System
Operation
The SBS-RC can be changed to
inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS-RC is cancelled, the SBS
OFF indicator light turns on.
NOTE
xWhen the ignition is switched OFF
while the SBS-RC is cancelled, the
SBS-RC is automatically enabled the
next time the ignition is switched
ON.
xWhen the SBS-RC is cancelled, the
Smart Brake Support [Rear] (SBS-R)
is also cancelled.
When Driving
i-ACTIVSENSE
4-184