2019 MAZDA MODEL CX-30 mazda connect

xThe battery voltage has decreased.xThe front side radar sensor of the
FCTA may be regulated under the
radio wave related laws of the
country where the vehicle is driven.
If this system is used abroad, it may
be necessary to turn off the system.
Refer to Front Side Radar Sensor
on page 4-222.
▼Cancelling Operation of Front
Cross Traffic Alert (FCTA)
The FCTA can be set to inoperable.
x(If only the FCTA is turned
off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the FCTA is turned off by
operating the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
Rear Cross Traffic Alert
(RCTA)
*
▼Rear Cross Traffic Alert (RCTA)
The RCTA system is designed to assist
the driver in checking the area to the
rear left and right sides of your vehicle
while your vehicle is reversing by
alerting the driver to the presence of
vehicles approaching the rear of your
vehicle.
The RCTA system detects vehicles
approaching from the rear left and
right sides of your vehicle and the rear
of your vehicle while your vehicle is
being reversed out of a parking space,
and notifies the driver of possible
danger using the Blind Spot Monitoring
(BSM) warning indicator lights and the
warning buzzer.
1. Your vehicle
2. Detection areas
When Driving
i-ACTIVSENSE
4-126*Some models.

xIn the following cases, it may be
difficult to view the illumination/
flashing of the Blind Spot Monitoring
(BSM) warning indicator lights
equipped on the door mirrors.
xSnow or ice adheres to the door
mirrors.
xThe front door glass is fogged or
covered in snow, frost or dirt.
xTurn off the RCTA system while
pulling a trailer or while an accessory
such as a bicycle carrier is installed to
the rear of the vehicle. Otherwise,
the radio waves emitted by the radar
will be blocked causing the system to
not operate normally.
xThe rear side radar sensor of the
RCTA may be regulated under the
radio wave related laws of the
country where the vehicle is driven. If
this system is used abroad, it may be
necessary to turn off the system.
Refer to Rear Side Radar Sensor on
page 4-224.
xIf a Mazda genuine trailer hitch is
used, the RCTA is automatically
turned off.
▼Cancelling Operation of Rear
Cross
Tra ffi c Alert (RCTA)
The RCTA can be set to inoperable.
x(If only the RCTA is turned off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the RCTA is turned off by
operating the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
When Driving
i-ACTIVSENSE
4-129

For safety purposes, switch the MRCC
system off when it is not being used.
Leaving the MRCC system turned on
when it is not in use is dangerous as it
could operate unexpectedly, resulting
in an accident.
CAUTION
¾Turn the system off when the vehicle
is running on a chassis roller.
¾If your vehicle is towed or you are
towing something , switch the MRCC
system off to prevent an unexpected
operation.
NOTE
xThe MRCC system does not detect
the following as physical objects.
xVehicles approaching in the
opposite direction
xPedestriansxStationary objects (stopped
vehicles, obstructions)
xIf a vehicle ahead is travelling at an
extremely low speed, the system
may not detect it correctly.
xIf there is a structure on the road or
an object (such as a monorail) at a
low height off the ground in front of
the vehicle, the system may operate.
Therefore, do not use the MRCC.
xDo not use the MRCC system under
conditions in which close proximity
warnings are frequently activated.
xDuring headway control travel, the
system accelerates and decelerates
your vehicle in conjunction with the
speed of the vehicle ahead.
However, if it is necessary to
accelerate for a lane change or if the
vehicle ahead brakes suddenly
causing you to close in on the vehicle
rapidly, accelerate using the
accelerator pedal or decelerate using
the brake pedal depending on the
conditions.
xWhile the MRCC system is in use, it
does not cancel even if the selector
lever (automatic transmission)/shift
lever (manual transmission) is
operated and any intended engine
braking will not occur. If deceleration
is required, lower the vehicle speed
setting or depress the brake pedal.
xWhile braking by the MRCC control
is operating, you might hear an
operation sound, however, this does
not indicate a problem.
xThe brake lights turn on while
braking by the MRCC control is
operating , however, they may not
turn on while the vehicle is on a
down slope at the set vehicle speed
or travelling at a constant speed and
following a vehicle ahead.
xStop the headway control function to
switch the system to the cruise
control function.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Mazda Radar Cruise Control
(MRCC) Display Indication
The MRCC setting status and operation
conditions are indicated on the
multi-information display and the
active driving display.
When Driving
i-ACTIVSENSE
4-131

xDuring headway control travel, the
system accelerates and decelerates
your vehicle in conjunction with the
speed of the vehicle ahead.
However, if it is necessary to
accelerate for a lane change or if the
vehicle ahead brakes suddenly
causing you to close in on the vehicle
rapidly, accelerate using the
accelerator pedal or decelerate using
the brake pedal depending on the
conditions.
xWhile the MRCC with Stop & Go
function system is in use, it does not
cancel even if the selector lever is
operated and any intended engine
braking does not occur. If
deceleration is required, lower the
set speed or depress the brake
pedal.
xWhile braking by the MRCC with
Stop & Go function control is
operating , you might hear an
operation sound, however, this does
not indicate a problem.
xThe brake lights turn on while
braking by the MRCC with Stop &
Go function control is operating,
however, they may not turn on while
the vehicle is on a down slope at the
set vehicle speed or travelling at a
constant speed and following a
vehicle ahead.
xStop the headway control function to
switch the system to the cruise
control function.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Mazda Radar Cruise Control with
Stop & Go function (MRCC with
Stop & Go function) Display
Indication
The MRCC with Stop & Go function
setting status and operation conditions
are indicated on the multi-information
display and the active driving display.
Multi-information Display (Basic
display)
1. Vehicle ahead display
2. MRCC with Stop & Go function set
vehicle speed

Multi-information Display
(i-ACTIVSENSE display)
1. Vehicle ahead display
2. MRCC with Stop & Go function set
vehicle speed

Active driving display
1. Vehicle ahead display
When Driving
i-ACTIVSENSE
4-141

(warning/risk avoidance support
system) (white) and the i-ACTIVSENSE
warning indication/warning light on
the multi-information display turns on
and a message is indicated.
Refer to i-ACTIVSENSE Status Symbol
(Warning/Risk Avoidance Support
System) on page 4-96.
▼Steering Wheel Operation Assist
When the system determines that the
vehicle might be deviating from its
lane, the steering wheel operation
assist operates.
The system notifies the driver that it
provided steering wheel operation
assistance on the multi-information
display and the active driving display.
Multi-information display (Basic
display)
Multi-information display
(i-ACTIVSENSE display)
Active driving display
NOTE
When the driver operates the steering
wheel while the steering wheel
operation assist is operating , the
steering wheel operation assistance is
cancelled.
▼System Cancelling
The LAS can be set to inoperable.
x(If only the LAS is turned
off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the LAS is turned off by operating
the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
When Driving
i-ACTIVSENSE
4-165

▼Setting the System
WARNING
Always verify the safety of the
surrounding area when setting the
ISA:
If the speed is set lower than the
current vehicle speed, the vehicle
speed is decreased to the set speed.
Verify the safety of the surrounding
area and keep a safer distance
between vehicles ahead and behind
you.
NOTE
xThe system is temporarily cancelled
when the vehicle is accelerated by
depressing the accelerator pedal
strongly, however, it resumes when
the vehicle speed decreases to the
set speed or less.
xThe vehicle speed may exceed the
set speed on a down slope.
xIn the following cases, the system
cannot be set.
xAny door is open.xThe driver's seat belt is unfastened.xThe ISA setting can be changed to
MANUAL, or OFF*1.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
*1 When OFF is selected, the
Adjustable Speed Limiter (ASL) is
set.
Refer to Adjustable Speed Limiter
(ASL) on page 4-166.
How to set the speed limit using the
RES switch
1. Press the LIM switch to turn the
system on.
2. Press the RES switch up (SET+) or
down (SET-) to set the speed.
When the current vehicle speed is
30 km/h (19 mph) or more, the
speed is set to the current vehicle
speed. When the current vehicle
speed is less than 30 km/h (19
mph), the speed is set to 30 km/h
(19 mph).
3. To increase the set speed, press the
RES switch up (SET+) continuously.
The set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES switch up (SET
+) momentary. For example, the set
speed increases about 4 km/h (4
mph) by pressing the RES switch up
(SET+) switch 4 times.
4. To decrease the set speed, press the
RES switch down (SET-)
continuously. The set speed can be
adjusted in 10 km/h (5 mph)
increments. The set speed can also
be adjusted in about 1 km/h (1
mph) increments by pressing the
RES switch down (SET-)
momentary. For example, the set
speed decreases about 4 km/h (4
mph) by pressing the RES switch
down (SET-) 4 times.
NOTE
xWhen the vehicle set speed is
displayed in the active driving
display/instrument cluster and speed
limit sign is not displayed, press the
RES switch to set the displayed
vehicle speed.
Manually setting the vehicle speed
limit from a speed limit sign
1. Press the LIM switch to turn the
system on.
2. Press the RES switch while the ISA
set indication is displayed on the
active driving display/instrument
When Driving
i-ACTIVSENSE
4-173

cluster to set the vehicle speed limit
to the speed of the displayed speed
limit sign.
1. Speed limit sign setting indication
NOTE
xThe speed limit cannot be set from
the speed limit sign when the speed
limit sign indication is displayed in
gray.
Excessive speed range setting
The range of speed that can exceed the
set speed can be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x+ 0: The vehicle speed is restricted at
the set speed.
x+ 5: If the vehicle speed exceeds the
set speed by 5 km/h (3mph), the
vehicle speed is restricted.
x+ 10: If the vehicle speed exceeds
the set speed by 10 km/h (5 mph),
the vehicle speed is restricted.
▼Temporarily Cancelling the System
The system is temporarily cancelled
(stand-by status) when any of the
following operations is done while the
ISA is displayed.
xCANCEL switch is pressedxAccelerator pedal is strongly
depressed
xAny door is openedxThe driver’s seat belt is unfastened
NOTE
xThe set speed can be set by pressing
the RES switch up (SET+) or down
(SET-) while the system is in stand-by
status.
xThe ISA is not cancelled by
depressing the brake pedal.
When Driving
i-ACTIVSENSE
4-174

1. “BRAKE!” message is displayed
NOTE
xThe collision warning sound is
activated intermittently while the SBS
brake or brake assist (SBS brake
assist) is operating.
xThe operation distance and volume
of the collision warning can be
changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Stopping the Smart Brake Support
(SBS) System Operation
The SBS can be changed to inoperable.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When the SBS is cancelled, the SBS
OFF indicator light turns on.
NOTE
When the ignition is switched OFF
while the SBS is cancelled, the SBS is
automatically enabled the next time
the ignition is switched ON.
Smart Brake Support
[Rear] (SBS-R)
*
▼Smart Brake Support [Rear]
(SBS-R)
The SBS-R is a system which is
designed to reduce damage in the
event of a collision by operating the
brake control (SBS brake) when the
system’s sensors detect an obstruction
at the rear of the vehicle while driving
at a speed of about 2 to 8 km/h (2 to
4 mph) and the system determines that
a collision is unavoidable.
WARNING
Do not rely completely on the SBS-R
system:
¾The
SBS-R system is only designed to
reduce damage in the event of a
collision. Over reliance on the system
leading to the accelerator pedal or
brake pedal being mistakenly
operated could result in an accident.
¾To assure the correct operation of
the
SBS-R, heed the following
cautions.
When Driving
i-ACTIVSENSE
*Some models.4-177