2019 MAZDA MODEL CX-30 mazda connect

WARNING
Do not rely completely on the vehicle
roll prevention function.
¾The vehicle roll prevention function
is a supplementary function which
operates for a maximum of 2
seconds after releasing the brake
pedal and accelerating the vehicle
from an engine idling stop condition.
Over reliance on the system may
result in an unexpected accident if
the vehicle were to suddenly
accelerate. Before starting to drive
the vehicle, always confirm the safety
of the surroundings and operate the
selector lever, brake pedal, and
accelerator pedal appropriately.
Note that the vehicle may move
suddenly depending on the vehicle's
load or if it is towing something.
¾Note that the vehicle may move
suddenly after the vehicle roll
prevention function is released while
the vehicle is under the following
conditions:
¾The selector lever is in the N
position.
¾If the selector lever is shifted to the
N position and the brake pedal is
released while the i-stop function
is operating, the brake force is
gradually released. To accelerate
the vehicle, release the brake pedal
after the engine restarts and shift
the selector lever to a position
other than the N position.
NOTE
xWhen the vehicle is stopped on a
steep grade, the vehicle roll
prevention function does not
operate because engine idling is not
stopped.
xThe brake pedal response may
change, sound may occur from the
brakes, or the brake pedal could
vibrate from the operation of the
vehicle roll prevention function.
However, this does not indicate a
malfunction.
▼i-stop Warning Light (Amber)/
i-stop Indicator Light (Green)
To ensure safe and comfortable use of
the vehicle, the i-stop system
constantly monitors the driver's
operations, the vehicle's interior and
exterior environment, and the
operational status of the vehicle, and
uses the i-stop warning light (amber)
and i-stop indicator light (green) to
inform the driver of various cautions
and warnings.
NOTE
On vehicles equipped with the centre
display, the i-stop operation status is
displayed in the fuel efficiency monitor
display.
Refer to the Fuel Efficiency Monitor
section in the Mazda Connect
Owner's Manual.
i-stop warning light (amber)
When the light is turned on
xThe light turns on when the ignition
is switched ON and turns
off when
the engine is started.
x(European model)
The light turns on if the following
operations are performed while
engine idling is stopped. In such
cases, the engine does not restart
When Driving
Start/Stop Engine
4-18

The screen content changes each time the INFO switch is pressed.
1. Basic display
2. Drive information display
3. i-ACTIVSENSE display
4. Message display
*1
*1 Displayed only when a warning occurs.

The type of display for the fuel economy and the maximum driving distance can be
changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
When Driving
Instrument Cluster and Display
4-24

▼Outside Temperature Display
When the ignition is switched ON, the
outside temperature is displayed.

NOTE
xUnder the following conditions, the
outside temperature display may
differ from the actual outside
temperature depending on the
surroundings and vehicle conditions:
xSignificantly cold or hot
temperatures.
xSudden changes in outside
temperature.
xThe vehicle is parked.xThe vehicle is driven at low speeds.
Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and
Fahrenheit.
Settings can be changed by operating
the centre display screen.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
When the temperature unit indicated
in the outside temperature display is
changed, the temperature unit
indicated in the engine coolant gauge
display changes in conjunction with it.
Outside Temperature Warning*
When the outside temperature is low,
the indication flashes and a beep
sound is heard to warn the driver of
the possibility of icy roads.
If the outside temperature is lower
than about 4 °C (39 °F), the outside
temperature display and the
mark
flashes for about 3 seconds and a beep
sound is heard once.
NOTE
If the outside temperature is lower
than -20 °C (-4 °F), the beep sound
does not operate. However, the
mark illuminates.
▼Distance-to-empty
This displays the approximate distance
you can travel on the remaining fuel
based on the fuel economy.
The distance-to-empty will be
calculated and displayed every second.

NOTE
xEven though the distance-to-empty
display may indicate a
sufficient
amount of remaining driving distance
before refuelling is required, refuel as
soon as possible if the fuel level is
very low or the low fuel warning light
illuminates.
xThe display will not change unless
you add more than approximately 9
L (2.3 US gal, 1.9 Imp gal) of fuel.
When Driving
Instrument Cluster and Display
4-28*Some models.

▼Deceleration Regeneration Charge
Display (M Hybrid)
This displays the status of the charging
produced by deceleration
regeneration.
Refer to M Hybrid on page 4-86.
▼Vehicle Speed Alarm*
In this mode, the current setting for the
vehicle speed alarm is displayed. You
can change the vehicle speed setting at
which the warning is triggered.
NOTE
The vehicle speed alarm display is
activated at the same time the beep
sound is heard.
1. “Speed Alert” message is displayed

The vehicle speed alarm can be set
using the centre display.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
NOTE
Always set the vehicle speed according
to the laws and regulations of the
country/city in which the vehicle is
driven. In addition, always verify the
speed of the vehicle using the
speedometer.
▼i-ACTIVSENSE Display
Displays the system status.

xRefer to Lane Departure Warning
System (LDWS) on page 4-105.
xRefer to Blind Spot Monitoring
(BSM) on page 4-109.
xRefer to
Tra ffi c Sign Recognition
System (TSR) on page 4-113.
xRefer to Distance & Speed Alert
(DSA) on page 4-119.
xRefer to Driver Attention Alert (DAA)
on page 4-120.
xRefer to Driver Monitoring (DM) on
page 4-122.
xRefer to Front Cross Traffic Alert
(FCTA) on page 4-123.
xRefer to Mazda Radar Cruise Control
(MRCC) on page 4-131.
xRefer to Mazda Radar Cruise Control
with Stop & Go function (MRCC
with Stop & Go function) on page
4-141.
xRefer to Cruising & Traffic Support
(CTS) on page 4-152.
xRefer to Lane-keep Assist System
(LAS) on page 4-165.
xRefer to Adjustable Speed Limiter
(ASL) on page 4-166.
When Driving
Instrument Cluster and Display
4-30*Some models.

Refer to the Information section in
the Mazda Connect Owner's
Manual.
CAUTION
¾When the maintenance period
arrives, have your vehicle inspected
by an expert repairer (we
recommend an Authorised Mazda
Repairer) as soon as possible. If
maintenance is neglected, a
decrease in vehicle performance
may occur which could cause
damage. Have your vehicle
inspected before the maintenance
period arrives.
¾If the vehicle continues to be
driven after the engine oil
replacement period has passed, it
could cause damage to the engine.
Replace the engine oil before the
maintenance period arrives.
¾(SKYACTIV-D 1.8)
Depending on the vehicle use
conditions, engine oil replacement
is required due to engine oil
deterioration from fuel penetrating
the engine oil. If “Excessive Oil
Level. Have the Vehicle Inspected”
is displayed on the
multi-information display in the
instrument cluster, have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
x(SKYACTIV-D 1.8)
xWhen fuel filter (sedimentor)
draining is required. Consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
NOTE
xThe wrench indication/indicator
light may display/turn on earlier than
the preset period depending on
vehicle usage conditions.
xWhenever the engine oil is replaced,
a reset of the vehicle engine control
unit is necessary.
Refer to the Information section in
the Mazda Connect Owner's
Manual.

▼Glow Indicator Light (SKYACTIV-D
1.8)
When the ignition is switched ON, the
glow indicator light turns on. The glow
indicator light turns
off when
preheating is finished.

A problem in the system might be
indicated under the following
conditions. Have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe glow indicator light does not
turn on when the ignition is switched
ON or it remains on.
xThe glow indicator light is flashing.
NOTE
If the vehicle is left with the ignition
switched ON without starting the
engine and a long period of time has
elapsed since preheating
finished, the
preheating may be performed again
and the glow indicator light may turn
on.
When Driving
Instrument Cluster and Display
4-38

Lane Departure Warning System (LDWS) on page 4-105.xBlind Spot Monitoring (BSM) Operation Conditions and Warnings*
Refer to Blind Spot Monitoring (BSM) on page 4-106.xTraffic Sign Recognition System (TSR) traffic signs and Warnings*
Refer to Traffic Sign Recognition System (TSR) on page 4-111.xFront Cross
Tra ffi c Alert (FCTA) Operation Conditions and Warning*
Refer to Front Cross Traffic Alert (FCTA) on page 4-123.xMazda Radar Cruise Control (MRCC) Operation Conditions and Warnings*
Refer to Mazda Radar Cruise Control (MRCC) on page 4-130.xMazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go
function) Operation Conditions and Warnings*
Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop
& Go function) on page 4-139.
xCruising & Traffic Support (CTS) Operation Conditions and Warnings*
Refer to Cruising & Traffic Support (CTS) on page 4-148.xLane-keep Assist System (LAS) Warnings*
Lane-keep Assist System (LAS) on page 4-162.xIntelligent Speed Assistance (ISA) Operation Conditions and Warnings*
Refer to Intelligent Speed Assistance (ISA) on page 4-170.xAdjustable Speed Limiter (ASL) Operation Conditions and Warnings*
Refer to Adjustable Speed Limiter (ASL) on page 4-166.xSmart Brake Support (SBS) Operation Conditions and Warnings*
Refer to Smart Brake Support (SBS) on page 4-175.xSmart Brake Support [Rear] (SBS-R) Operation Conditions and Warnings*
Refer to Smart Brake Support [Rear] (SBS-R) on page 4-177.xSmart Brake Support [Rear Crossing]
(SBS-RC) Operation Conditions and
Warnings*
Refer to Smart Brake Support [Rear Crossing] (SBS-RC) on page 4-181.xCruise Control Operation Conditions
Refer to Cruise Control on page 4-228.
xNavigation Guidance (vehicles with navigation system)xIntersection Name (vehicles with navigation system)xStreet name (vehicles with navigation system)xLane Guidance (vehicles with navigation system)xSpeed limit indicator (vehicles with navigation system)xVehicle Speed
The active driving display settings can be changed or adjusted.
Refer to the Settings section in the Mazda Connect Owner's Manual.
NOTE
xThe desired driving position (display position, brightness level, display
information) can be called up after programming the position.
Refer to Driving Position Memory on page 2-10.
xThe street name may not be displayed depending on the market and region.
When Driving
Instrument Cluster and Display
4-40*Some models.

Auto-light control*
When the headlight switch is in a position other than and the ignition is
switched ON, the light sensor senses the surrounding lightness or darkness and
automatically turns the headlights and other exterior lights on or off.
CAUTION
¾Do not shade the light sensor by adhering a sticker or a label on the windscreen.
Otherwise the light sensor will not operate correctly.
¾The light sensor also works as a rain sensor for the auto-wiper control. Keep hands
and scrapers clear of the windscreen when the wiper lever is in the AUTO position
and the ignition is switched ON as fingers could be pinched or the wipers and
wiper blades could be damaged when the wipers activate automatically. If you are
going to clean the windscreen, be sure the wipers are turned
off completely when
it is particularly tempting to leave the engine running. This is particularly important
when clearing ice and snow.
NOTE
xThe headlights and other exterior lights may not turn off immediately even if the
surrounding area becomes well-lit because the light sensor determines that it is
night time if the surrounding area is continuously dark for several minutes such as
inside long tunnels, traffic jams inside tunnels, or in indoor parking lots.
xThe sensitivity of the auto-light control may be changed.
Refer to the Settings section in the Mazda Connect Owner's Manual.
When Driving
Switches and Controls
4-56*Some models.

▼Headlight High-Low Beam
The headlights switch between high
and low beams by moving the lever
forward or backward.

1. High beam
2. Low beam

When the headlight high-beams are
on, the headlight high-beam indicator
light is turned on.

▼Flashing the Headlights
The headlights can be flashed with the
ignition switched to ON.
To flash the headlights, pull the lever
fully towards you (the headlight switch
does not need to be on).

1. OFF
2. Headlight flashing

The headlight high-beam indicator
light in the instrument cluster
illuminates simultaneously. The lever
will return to the normal position when
released.

▼Coming Home Light
The coming home light turns on the
headlights (low beams) when the lever
is operated.
To turn on the lights
When the lever is pulled with the
ignition switched to ACC or OFF, the
low beam headlights turn on.
The headlights turn off after a certain
period of time has elapsed after all of
the doors are closed.
NOTE
xThe time until the headlights turn off
after all of the doors are closed can
be changed.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
xIf no operations are done for 3
minutes after the lever is pulled, the
headlights turn off.
xThe headlights turn off if the lever is
pulled again while the headlights are
illuminated.
▼Leaving Home Light
The leaving home light turns on the
lights when the transmitter unlock
button is pressed while away from the
vehicle.
When Driving
Switches and Controls
4-57