2019 MAZDA MODEL CX-30 battery

recommend an Authorised Mazda
Repairer).
WARNING
Never touch the areas where high
current is flowing:
Never touch a M Hybrid related part.
Otherwise, it could lead to an
electrical shock or burns causing
serious injury.
Never touch electrical wiring that may
be protruding into or outside of the
cabin:
Otherwise, it could lead to an
electrical shock or burns causing
serious injury.
Never touch any area where
electrolyte is visible or electrolyte is
leaking from the area:
If any electrolyte from the M Hybrid
battery gets in the eyes or on the skin,
it could cause loss of vision or skin
reactions. In the unlikely event that
electrolyte comes into contact with the
eyes or skin, flush with large quantities
of water immediately and seek
immediate medical attention.
Do not come near the vehicle if
electrolyte is leaking from the M
Hybrid battery:
Even if the M Hybrid battery is
damaged, large quantities of
electrolyte will not flow out due to the
internal structure of the battery,
however, in the unlikely event that it
does, it will produce steam. The steam
contains properties that can irritate the
eyes and skin, and could cause acute
poisoning if absorbed.
Never approach objects that are on
fire or extremely hot:
Electrolyte in the M Hybrid battery may
cause a fire.
If the vehicle catches fire, extinguish
the fire using an ABC fire
extinguisher:
Only extinguish a fire with water when
large amounts of water is available
such as from a fire hydrant.
When Driving
M Hybrid
4-89

2. Detection areas
WARNING
Always check the surrounding area
visually before making an actual lane
change:
The system is only designed to assist
you in checking for vehicles at your rear
when making a lane change. Due to
certain limitations with the operation
of this system, the BSM warning
indicator light, the warning sound and
the warning screen indicator display
may not activate or they might be
delayed even though a vehicle is in an
adjacent driving lane. Always make it
your responsibility as a driver to check
the rear.
NOTE
xThe BSM will operate when all of the
following conditions are met:
xThe ignition is switched ON.xThe i-ACTIVSENSE warning
indication/warning light in the
instrument cluster is turned off.
xThe vehicle speed is about 30
km/h (19 mph) or faster.
xThe BSM will not operate under the
following circumstances.
xThe vehicle speed falls below
about 25 km/h (15 mph) even
though the i-ACTIVSENSE warning
indication/warning light is turned
off.
xThe shift lever (manual
transmission)/selector lever
(automatic transmission) is shifted
to reverse (R) and the vehicle is
reversing.
xThe turning radius is small (making
a sharp turn, turning at
intersections).
xIn the following cases, the
i-ACTIVSENSE warning indication/
warning light turns on and operation
of the system is stopped. If the
i-ACTIVSENSE warning indication/
warning light remains illuminated,
have the vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system
including the BSM warning
indicator lights is detected.
xA large deviation in the installation
position of a rear side radar sensor
on the vehicle has occurred.
xThere is a large accumulation of
snow or ice on the rear bumper
near a rear side radar sensor.
Remove any snow, ice or mud on
the rear bumper.
xDriving on snow-covered roads for
long periods.
xThe temperature near the rear side
radar sensor becomes extremely
hot due to driving for long periods
on slopes during the summer.
xThe battery voltage has decreased.xUnder the following conditions, the
rear side radar sensor cannot detect
target objects or it may be difficult to
detect them.
xThe rear bumper around the rear
side radar sensor is deformed.
xRadio wave interference from a
radar sensor equipped on a nearby
vehicle.
xThe approaching vehicle is any of
the following shapes.
a) The size of the vehicle body is
extremely small.
b) The vehicle height is extremely
low or high.
c) A special type of vehicle with a
complex shape.
When Driving
i-ACTIVSENSE
4-107

xThe battery voltage has decreased.xThe front side radar sensor of the
FCTA may be regulated under the
radio wave related laws of the
country where the vehicle is driven.
If this system is used abroad, it may
be necessary to turn off the system.
Refer to Front Side Radar Sensor
on page 4-222.
▼Cancelling Operation of Front
Cross Traffic Alert (FCTA)
The FCTA can be set to inoperable.
x(If only the FCTA is turned
off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the FCTA is turned off by
operating the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
Rear Cross Traffic Alert
(RCTA)
*
▼Rear Cross Traffic Alert (RCTA)
The RCTA system is designed to assist
the driver in checking the area to the
rear left and right sides of your vehicle
while your vehicle is reversing by
alerting the driver to the presence of
vehicles approaching the rear of your
vehicle.
The RCTA system detects vehicles
approaching from the rear left and
right sides of your vehicle and the rear
of your vehicle while your vehicle is
being reversed out of a parking space,
and notifies the driver of possible
danger using the Blind Spot Monitoring
(BSM) warning indicator lights and the
warning buzzer.
1. Your vehicle
2. Detection areas
When Driving
i-ACTIVSENSE
4-126*Some models.

xA vehicle overtakes your vehicle
while it is stopped.
xYour vehicle is in an area where
strong radio waves or electrical
noise may occur such as near a
television tower or power plant.
xIn the following cases, the
i-ACTIVSENSE warning indication/
warning light turns on and operation
of the system is stopped. If the
i-ACTIVSENSE warning indication/
warning light remains illuminated,
have the vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system
including the Blind Spot
Monitoring (BSM) warning
indicator lights has occurred.
xA large deviation in the installation
position of a rear side radar sensor
on the vehicle has occurred.
xThere is a large accumulation of
snow or ice on the rear bumper
near a rear side radar sensor.
xDriving on snow-covered roads for
long periods.
xThe temperature near the radar
sensors becomes extremely hot
due to driving for long periods on
slopes during the summer.
xThe battery voltage has decreased.xUnder the following conditions, the
rear side radar sensor cannot detect
approaching vehicles or it might be
difficult to detect them, and the
system may not operate normally.
xThe vehicle speed when reversing
is about 15 km/h (9 mph) or
faster.
xThe rear side radar sensor
detection area is obstructed by a
nearby wall or parked vehicle.
(Reverse the vehicle to a position
where the radar sensor detection
area is no longer obstructed.)
1. Your vehicle

xA vehicle is approaching directly
from the rear of your vehicle.
1. Your vehicle

xThe vehicle is parked at an angle.
1. Your vehicle

xDirectly after the RCTA system
becomes operable using the
personalisation feature.
xRadio wave interference from a
radar sensor equipped on a nearby
parked vehicle.
When Driving
i-ACTIVSENSE
4-128

¾If cracks or damage caused by flying
gravel or debris is visible around a
rear radar and rear camera, stop
using the SBS-RC system
immediately and have your vehicle
inspected by an expert repairer (we
recommend an Authorised Mazda
Repairer). If the vehicle continues to
be driven with cracks or scratch
marks left around an ultrasonic
sensor, the system may operate
unnecessarily and cause an
unexpected accident.
Refer to Stopping the Smart Brake
Support [Rear Crossing] (SBS-RC)
System Operation on page 4-184.
¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for rear bumper
replacement.
Do not modify the suspension:
If the vehicle height or inclination is
changed, the
SBS-RC system may not
operate correctly because it cannot
detect obstructions correctly.
Do not apply a strong force to a rear
radar and rear camera:
When washing the vehicle, do not
spray highly pressurised water against a
rear radar and rear camera, or rub it
strongly. In addition, do not hit the rear
bumper forcefully when loading and
unloading cargo. Otherwise, the
sensors may not detect obstructions
correctly which could cause the
SBS-RC system to not operate
normally, or it could operate
unnecessarily.
NOTE
xThe SBS-RC system will operate
under the following conditions.
xThe engine is running.
xThe shift lever (manual
transmission vehicle) or the
selector lever (automatic
transmission vehicle) is in the R
(reverse) position.
xi-ACTIVSENSE warning indication/
warning light is not displayed in the
multi-information display.
xThe vehicle speed is under about
10 km/h (6 mph).
xThe vehicle speed of an
approaching vehicle is about 3
km/h (2 mph) or faster.
xThe SBS-R is not turned off.xThe DSC is not malfunctioning.xIn the following cases, the
i-ACTIVSENSE warning indication/
warning light turns on and operation
of the system is stopped. If the
i-ACTIVSENSE warning indication/
warning light remains illuminated,
have the vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as soon
as possible.
xSome problem with the system
including the SBS-RC system.
xA large deviation in the installation
position of a rear side radar sensor
on the vehicle has occurred.
xThere is a large accumulation of
snow or ice on the rear bumper
near a rear side radar sensor.
xDriving on snow-covered roads for
long periods.
xThe temperature near the radar
sensors becomes extremely hot
due to driving for long periods on
slopes during the summer.
xThe battery voltage has decreased.xUnder the following conditions, the
rear side radar sensor cannot detect
target objects or it may be difficult to
detect them.
When Driving
i-ACTIVSENSE
4-182

¾Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) for repair, painting , or
replacement of the front/rear
camera, front bumper, liftgate and
door mirrors.
¾Heed the following cautions to
assure that the 360°View Monitor
operates normally.
¾Do not modify the vehicle
suspensions or lower/raise the
vehicle body, or both.
¾Always use tyres of the
specified
type and size for the front and rear
wheels. Consult an expert repairer
(we recommend an Authorised
Mazda Repairer) for tyre
replacement.
¾When the display is cold, images
may leave trails or the screen might
be darker than usual, making it
difficult to check the vehicle
surroundings. Always
confirm the
safety at the front and around the
vehicle visually when driving.
¾The method for parking/stopping
the vehicle using the 360°View
Monitor
differs depending on the
road circumstances/conditions and
the vehicle conditions. When and
how much you turn the steering
wheel will differ depending on the
situation, , therefore always check
the vehicle surroundings directly with
your eyes while using the system.
Also, before using the system, always
make sure that the vehicle can be
parked/stopped in the parking/
stopping space.NOTE
xIf there are water droplets, snow, or
mud on the camera lens, wipe it off
using a soft cloth. If the camera lens
is especially dirty, wash it off with
mild detergent.
xIf the camera lens is touched or there
is any dirt on it, it could affect the
screen image. Wipe the lens using a
soft cloth.
xIf the area where the camera is
installed, such as the front bumper,
liftgate or door mirrors, has been
damaged in a vehicle accident, the
camera (position, installation angle)
may have shifted. Always consult an
expert repairer (we recommend an
Authorised Mazda Repairer) to have
the vehicle inspected.
xIf the camera is subjected to
excessive changes in temperature
such as by pouring hot water on the
camera during cold weather, the
360°View Monitor may not operate
normally.
xIf the battery voltage is low, the
screen might be temporarily difficult
to view, however, this does not
indicate a problem.
xThe 360°View Monitor has
limitations. Objects under the
bumper or near both ends of the
bumper cannot be displayed.
xObstructions above the upper image
range of the camera are not
displayed.
xUnder the following conditions, the
screen might be difficult to view,
however this does not indicate a
problem.
xThe temperature near the lens is
high/low.
xRainy conditions, water droplets
on the camera, or high humidity.
xMud or foreign matter near the
camera.
When Driving
i-ACTIVSENSE
4-187

xNarrow lane roads due to road
construction or lane closures.
xThe vehicle ahead enters the radar
sensor's blind spot.
xThe vehicle ahead is running
abnormally due to accident or
vehicle damage.
xRoads with repeated up and down
slopes
xDriving on poor roads or unpaved
roads.
xThe distance between your vehicle
and the vehicle ahead is extremely
short.
xA vehicle suddenly comes close,
such as by cutting into your lane.
xTo prevent incorrect operation of the
system, use tyres of the same
specified size, manufacturer, brand,
and tread pattern on all four wheels.
In addition, do not use tyres with
significantly different wear patterns
or tyre pressures on the same vehicle
(Including the temporary spare tyre).
xIf the battery power is weak, the
system may not operate correctly.
xWhen driving on roads with little
traffic and few vehicles ahead or
obstructions for the front radar
sensor to detect, “Safety and Driver
Support Systems Temporarily
Disabled. Front Radar Obscured.
Drive Safely” may be temporarily
displayed, however, this does not
indicate a problem.
xThe radar sensors are regulated by
the relevant radio wave laws of the
country in which the vehicle is
driven. If the vehicle is driven
abroad, authorization from the
country in which the vehicle is driven
may be required.
Front Side Radar Sensor*
▼Front Side Radar Sensor
Your vehicle is equipped with front
side radar sensor. The following
systems also use the front side radar
sensor.
xFront Cross Traffic Alert (FCTA)
The front side radar sensor function by
detecting the radio waves reflected off
a vehicle approaching from the front or
an obstruction sent from the radar
sensor.
1. Front side radar sensor

The front side radar sensors are
installed inside the front bumper, one
on each side.
Always keep the surface of the front
bumper near the front side radar
sensors clean so that they operate
normally. Also, do not apply items such
as stickers.
Refer to Exterior Care on page 6-54.
CAUTION
If the front bumper receives a severe
impact, the system may no longer
operate normally. Stop the system
immediately and have the vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
When Driving
i-ACTIVSENSE
4-222*Some models.

Please note that the TPMS is not a
substitute for proper tyre
maintenance, and it is the driver's
responsibility to maintain correct tyre
pressure, even if under-inflation has
not reached the level to trigger
illumination of the TPMS low tyre
pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to
indicate when the system is not
operating properly.
The TPMS malfunction indicator is
combined with the low tyre pressure
telltale. When the system detects a
malfunction, the telltale will flash for
approximately one minute and then
remain continuously illuminated.
This sequence will continue upon
subsequent vehicle start-ups as long
as the malfunction exists. When the
malfunction indicator is illuminated,
the system may not be able to detect
or signal low tyre pressure as
intended. TPMS malfunctions may
occur for a variety of reasons,
including the installation of
replacement or alternate tyres or
wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more
tyres or wheels on your vehicle to
ensure that the replacement or
alternate tyres and wheels allow the
TPMS to continue to function
properly.
¾To avoid false readings, the system
samples for a little while before
indicating a problem. As a result it
will not instantaneously register a
rapid tyre deflation or blow out.▼If there is a problem with the Tyre
Pressure Monitoring System
(TPMS)
If the TPMS warning light flashes, there
may be a problem with the system.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) to have the system inspected.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Flashing) on page
7-57.
In the following cases, the system
cannot recognise the tyre pressures
correctly and the TPMS warning light
may flash.
xThere is equipment or a device
nearby emitting radio signals the
same as a tyre pressure sensor.
xA metallic object such as a
non-genuine electronic device is
installed near the centre of the
instrument panel (obstructs the radio
signals from the tyre pressure sensors
to the receiver).
xA device such as one of the following
is used in the cabin.
xElectronic devices such as a
computer.
xConverter devices such as a
DC-AC converter.
xThere is a large accumulation of
snow or ice around the vehicle tyres.
xThe battery in a tyre pressure sensor
is dead.
xA wheel not equipped with a tyre
pressure sensor is used.
xTyres employing steel in the sidewall
of the tyre are installed.
xTyre chains are used.
▼When a tyre pressure decreases
If the TPMS warning light turns on, a
tyre pressure may be low. Inspect the
When Driving
Tyre Pressure Monitoring System (TPMS)
4-233