2019 MAZDA MODEL CX-30 stop start

Cylinder Deactivation*
▼Cylinder Deactivation
The cylinder deactivation is a function
designed to reduce fuel consumption
and improve fuel economy by
deactivating 2 out of the 4 cylinders
while driving. The function constantly
determines which is better for driving;
4 cylinders or 2 cylinders, regardless of
the driver's operations, and it performs
the switching automatically.
When the cylinder deactivation
function does not operate
The cylinder deactivation function
does not operate under the following
conditions.
xThe selector lever is in the P, N, or R
position (automatic transmission), or
1st gear (manual transmission).
xThe engine oil temperature or engine
coolant temperature is low.
xAfter disconnecting the battery
terminals for some reason, such as
for battery replacement.
When Driving
Start/Stop Engine
4-20*Some models.

Signal Warning Refer to
*Low Washer Fluid Level Warning Indication/Warning Light7-60
Door-Ajar Warning Indication 7-60
Liftgate-Ajar Warning Indication 7-60
Door-Ajar Warning Light 7-60
*1 The light turns on when the ignition is switched on for an operation check, and turns off a few
seconds later or when the engine is started. If the light does not turn on or remains turned on, have
the vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).
▼Indication/Indicator Lights
These lights turn on or flash to notify the user of the system operation status or a
system malfunction.
Signal Indicator Refer to
(Green)Seat Belt Indicator Light (Rear seat) 2-24
*Front Passenger Air Bag Deactivation Indicator Light2-51
Security Indicator LightImmobilizer
System
3-48
Theft-Deterrent
System
3-50
Malfunction
7-56
(Green)KEY Indicator Light 4-5
(Green)
*i-stop Indicator Light4-18
When Driving
Instrument Cluster and Display
4-34*Some models.

Signal Indicator Refer to
(Green)
*Mazda Radar Cruise Control (MRCC) Set Indication4-134
*Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) Set Indication4-143
*Cruising &
Tra ffi c Support (CTS) Set Indication4-154
*Smart Brake Support (SBS) OFF Indicator Light*1
Smart Brake
Support (SBS)
4-177
Smart Brake
Support [Rear]
(SBS-R)
4-180
Smart Brake
Support [Rear
Crossing]
(SBS-RC)
4-184
(White)
*Intelligent Speed Assistance (ISA) Standby Indication4-171
*Adjustable Speed Limiter (ASL) Standby Indication4-167
(Green)
*Intelligent Speed Assistance (ISA) Set Indication4-171
*Adjustable Speed Limiter (ASL) Set Indication4-167
(White)
*Cruise Standby Indication4-228
(Green)
*Cruise Set Indication4-228
*1 The light turns on when the ignition is switched on for an operation check, and
turns off a few seconds later or when the engine is started. If the light does not
turn on or remains turned on, have the vehicle inspected at an expert repairer
(we recommend an Authorised Mazda Repairer).
*2 The light turns on continuously when the parking brake is applied.
▼Wrench Indication/Indicator LightThe wrench indication/indicator light
is displayed/turns on under the
following conditions.
xWhen the preset maintenance
period has arrived.
When Driving
Instrument Cluster and Display
*Some models.4-37

The parking brake may be applied
automatically to prevent the vehicle
from moving if the engine stalls while
the vehicle is on a slope.
x(With i-stop function)
If the engine has stopped due to
stalling, it can be restarted by
depressing the clutch pedal within 3
seconds of the engine stopping.
The engine cannot be restarted even
if the clutch pedal is depressed
under the following conditions:
xThe driver's door is open.xThe driver's seat belt is unfastened.xThe clutch pedal is not released
completely after the engine stalled.
xThe clutch pedal is depressed with
the engine not stopped
completely.
▼Gear Shift Indicator (GSI)
The GSI supports you to obtain
optimum fuel economy and smooth
driving. It displays the selected gear
position in the instrument cluster as
well as
notifies the driver to change to
the most suitable gear position
corresponding to the actual driving
condition.

1. Selected gear position
2. Suitable gear position
Indication Condition
NumeralThe selected gear position is
displayed.
Indication Condition
and numer-
alShift up or down to the indi-
cated gear position is recom-
mended.
CAUTION
Do not rely solely on the shift-up/
shift-down recommendations by
indications. The actual driving situation
might require shift operations different
from indication. To avoid the risk of
accidents, the road and traffic
conditions have to be judged correctly
by the driver before shifting.
NOTE
The GSI turns off when the following
operations are performed.
xThe vehicle is stopped.xThe vehicle is put in neutral.xThe vehicle is driven in reverse.xThe clutch is not fully engaged when
accelerating from a stop.
xThe clutch pedal remains depressed
for 2 seconds or longer while driving.
When Driving
Manual Transmission Operation
4-42

Transmission Ranges
▼Transmission Ranges
xThe shift position indication in the
instrument cluster illuminates.
Refer to Shift Position Indication on
page 4-46.
xShift the selector lever to the P or N
position to start the engine.
P (Park)
P locks the transmission and prevents
the front wheels from rotating.
WARNING
Always set the selector lever to P
position and set the parking brake:
Only setting the selector lever to the P
position without using the parking
brake to hold the vehicle is dangerous.
If P fails to hold, the vehicle could
move and cause an accident.
CAUTION
¾Shifting into P, N or R while the
vehicle is moving can damage your
transmission.
¾Shifting into a driving gear or reverse
when the engine is running faster
than idle can damage the
transmission.
R (Reverse)
In position R, the vehicle moves only
backward. You must be at a complete
stop before shifting to or from R,
except under rare circumstances as
explained in Rocking the Vehicle (page
3-56).
N (Neutral)
In N, the wheels and transmission are
not locked. The vehicle will roll freely
even on the slightest incline unless the
parking brake or brakes are on.
WARNING
If the engine is running faster than
idle, do not shift from N or P into a
driving gear:
It's dangerous to shift from N or P into
a driving gear when the engine is
running faster than idle. If this is done,
the vehicle could move suddenly,
causing an accident or serious injury.
Do not shift into N when driving the
vehicle:
Shifting into N while driving is
dangerous. Engine braking cannot be
applied when decelerating which
could lead to an accident or serious
injury.
CAUTION
Do not shift into N when driving the
vehicle. Doing so can cause
transmission damage.
NOTE
Apply the parking brake or depress the
brake pedal before moving the selector
lever from N position to prevent the
vehicle from moving unexpectedly.
D (Drive)
D is the normal driving position. From
a stop, the transmission will
automatically shift through a 6-gear
sequence.
M (Manual)
M is the manual shift mode position.
Gears can be shifted up or down by
operating the selector lever.
Refer to Manual Shift Mode on page
4-46.
When Driving
Automatic Transmission
4-45

*1 When the light switch is switched to a
different position from the OFF, position while the
vehicle is stopped, the running lights turn off. When starting to drive the vehicle, the running lights
turn on again.
*2 When the light switch is switched to the OFF position, and then to the position again, the
running lights turn off directly after starting the engine. The running lights turn on when you begin
driving the vehicle.
With auto-light control
Ignition Position ACC or OFF ON
Switch Position
OFF
*1AUTOOFF*1AUTO
Headlights Off Off Off Off
Auto
*2*4Auto*3*4
On
Running lights
*Off Off Off Off Off
Ta i l l i g h t s
Po s i t i o n l i g h t s
Number plate
lightsOff Off On Off On
*1 The light switch returns to the AUTO position automatically.*2 During the daytime, the running lights turn on automatically. During the nighttime, the headlights,
position lights, tail lights, and the number plate lights turn on automatically.
*3 During the daytime, the running lights, position lights, tail lights, and the number plate lights turn on
automatically. During the nighttime, the headlights, position lights, tail lights, and the number plate
lights turn on automatically.
*4 When the light switch is switched to the OFF position while the vehicle is stopped, all of the lights
that are turned on turn off. When the light switch is switched from a position other than
to the
position while the vehicle is stopped, the running lights or the headlights turn off. When
starting to drive the vehicle, the lights that are turned
off turn on again.
NOTE
The running lights can be disabled using the personalisation features (page 4-58).
When Driving
Switches and Controls
*Some models.4-55

Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Windscreen Washer
Pull the wiper lever toward you to
spray washer fluid and operate the
windscreen wipers several times. The
washer fluid is sprayed only while the
windscreen wipers move out of their
stowed positions to the point where
they start reversing back.

1. OFF
2. Washer
NOTE
xIf the windscreen washer is turned
on when the windscreen wipers are
not operating, the windscreen
wipers operate a few times.
xIf you pull the wiper lever while the
windscreen wipers are reversing back
to their stowed positions, the next
time the washer
fluid is sprayed is
during the next cycle.
If the washer does not work, inspect
the fluid level (page 6-31). If the fluid
level is normal, consult an expert
repairer (we recommend an
Authorised Mazda Repairer).
Rear Window Wiper and
Washer
▼Rear Window Wiper and Washer
The ignition must be switched ON to
use the wiper.
▼Rear Window Wiper
Turn the wiper on by turning the rear
wiper/washer switch.
Switch Position Wiper operation
Spray washer fluid and op-
erate the rear wiper
Type A Type B
Normal
ON
Type A Type B
Intermittent
INT
OFF Stop
Spray washer fluid and op-
erate the rear wiper
▼Rear Window Washer
To spray washer fluid, turn the rear
wiper/washer switch to either of the
position. After the switch is
released, the washer will stop.
When Driving
Switches and Controls
4-64

NOTE
While the windscreen washers are
operating (from the time the wiper
lever is pulled until the washer fluid
stops spraying), the rear window
washer does not spray washer fluid
even if you operate the switch.
If the washer does not work, inspect
the fluid level (page 6-31). If the fluid
level is normal and the washer still
does not work, consult an expert
repairer (we recommend an
Authorised Mazda Repairer).Headlight Washer*
▼Headlight Washer
The engine must be started and the
headlights must be turned on.

If you want to operate headlight
washers, double
flick the wiper lever.

1. OFF
2. Washer
NOTE
xWhen the windscreen washer is
operated for the first time after
turning on the headlights, the
headlight washers operate
automatically.
xIf air enters the headlight washer
fluid pipe under conditions such as
when the vehicle is brand-new or
after an empty washer tank is
replenished with washer fluid,
washer fluid will not spray even
when the wiper lever is operated. If
this occurs, perform the following
procedure:
1. Start the engine.
2. Turn on the headlights.
3. Double flick the wiper lever
several times until the washer
fluid sprays.
When Driving
Switches and Controls
*Some models.4-65