2019 MAZDA MODEL CX-30 battery

xIf the Mazda ERA-GLONASS operates while you are making a call with your
mobile phone using Bluetooth® Hands-Free, the call may be interrupted.xIt may not be possible to receive a call using the Bluetooth® Hands-Free normally
while the Mazda ERA-GLONASS is operating.
xA voice call with an operator may not be possible if the speaker or microphone is
broken. If the speaker or microphone is broken, always have the vehicle inspected
at an Authorised Mazda Repairer.
xThe Mazda ERA-GLONASS may not operate normally outside of the following
temperature range: If the Mazda ERA-GLONASS does not operate normally, make
a call from another telephone such as the nearest available public telephone.
Operation temperature range: -40 °C (-40 °F) to 85 °C (185 °F)
xThere may be a difference between the position information sent to the call centre
and the actual position of the vehicle where the call was made. Indicate
landmarks around the position of the vehicle where the call is being made to the
operator during the voice call.
Automatic emergency calls
If the vehicle receives an impact of a certain level or more in a collision, vehicle
information is automatically sent to the call centre.
When the transmission of the vehicle information is completed or about 20 seconds
have elapsed since the transmission began, the voice call with the call centre starts.
CAUTION
If an automatic call is made, the built-in battery power may be depleted and
emergency calls may not be possible in the event that an emergency occurs again.
After an automatic emergency call has been made, have the built-in battery replaced
by an Authorised Mazda Repairer.
NOTE
xAutomatic emergency calls cannot be cancelled by the user.xThe call centre will end an emergency call. The user cannot end the emergency
call.
xIf the vehicle receives an impact of a certain level or more in a collision, an
automatic call is made even if the air bags do not deploy.
xIf a call is disconnected or a call cannot be made to the call centre correctly, an
automatic call is made again to the call centre. Redialing cannot be cancelled.
1. If the vehicle receives an impact of a certain level or more in a collision, the
Mazda ERA-GLONASS begins operating automatically.
If Trouble Arises
Mazda
ERA-GLONASS
7-16

StatusIndicator light
Beep sound
statusOn/flashing conditions
Green Red Flash interval
Malfunction Turns off Turns onŠ3 beeps
(Slow intermit-
tent sound)
xA system malfunction is
detected.
xThe remaining power of
the built-in battery is low.
CAUTION
If the indicator light (red) re-
mains on constantly, the sys-
tem will not operate normal-
ly. Have the vehicle inspected
at an expert repairer (we rec-
ommend an Authorised Maz-
da Repairer) as soon as possi-
ble.
Call being
made with call
centreFlashes Turns offSlow
(0.5 second
intervals)The beep does
not sound, but
the ringback
tone can be
heard.An emergency call is being
made by the Mazda
ERA-GLONASS.
Vehicle infor-
mation is be-
ing transmittedFlashes Turns
offSomewhat
quick
(0.3 second
intervals)Continuous in-
termittent
soundVehicle information is being
transmitted to the call centre.
Start of voice
callTu r n s o n Tu r n s o ffŠ1 beep
During a voice call with the
call centre.
During voice
callTu r n s o n Tu r n s
offŠŠ
Connection
failureFlashes Turns onQuick
(0.15 second
intervals)3 beeps
(Fast intermit-
tent sound)When an emergency call fails
to connect.
▼Te s t M o d e
The test mode function makes sure that the Mazda ERA-GLONASS can operate
normally.
Have your vehicle tested at an Authorised Mazda Repairer when performing the test
mode.
Method to start test mode
Switch the ignition ON while the parking brake is applied, and wait 2 minutes with
the vehicle stopped.
If Trouble Arises
Mazda
ERA-GLONASS
7-20

Jump-Starting
▼Jump-Starting
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If
you feel unsure about jump-starting, we strongly recommend that you have a
competent service technician do the work.
WARNING
Follow These Precautions Carefully:
To ensure safe and correct handling of the battery, read the following precautions
carefully before using the battery or inspecting it.
Keep flames and sparks away from open battery cells and do not allow
metal tools to contact the positive (+) or negative (–) terminal of the battery when
working near a battery. Do not allow the positive (+) terminal to contact the
vehicle body:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all
flames including
cigarettes and sparks away from open battery cells.
Keep all
flames and sparks away from open battery cells because hydrogen
gas is produced from open battery cells while charging the battery or adding
battery
fluid:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. Keep all
flames including
cigarettes and sparks away from open battery cells.
Do not jump-start a frozen battery or one with a low fluid level:
Jump-starting a frozen battery or one with a low fluid level is dangerous. It may
rupture or explode, causing serious injury.
Connect the negative lead to a good ground point away from the battery:
Connecting the end of the second jumper lead to the negative (–) terminal of the
discharged battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
If Trouble Arises
Battery Runs Out
7-39

Route the jumper leads away from parts that will be moving:
Connecting a jumper lead near or to moving parts (cooling fans, belts) is dangerous.
The lead could get caught when the engine starts and cause serious injury.
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and
other electrical parts beyond repair with a 24 V power supply (two 12 V batteries in
series or a 24 V motor generator set).
1. Move the booster vehicle so that its battery is as close as possible to your
vehicle's battery.
2. Make sure that the power such as for the headlights and air conditioner is turned
off.
3. Remove the battery cover.
4. Turn off the booster vehicle's engine and connect the jumper leads in the
following order.
Make sure that the jumper leads are securely connected so that they do not
disconnect due to engine vibrations.
1st lead
Positive (+) terminal on the discharged battery
Positive (+) terminal on booster vehicle's battery
2nd lead
Negative (-) terminal on booster vehicle's battery
If Trouble Arises
Battery Runs Out
7-40

Location shown in the figure (do not connect to the negative (-) terminal of
the battery)
5. Start the booster vehicle's engine and rev the engine.
6. Start the engine of your vehicle. Run the engines for about 3 minutes to
temporarily charge the battery of your vehicle.
7. Disconnect the jumper leads in the reverse order of their connection.
8. Install the battery cover.
9. Have your vehicle inspected by an expert repairer (we recommend an Authorised
Mazda Repairer) as soon as possible.
If Trouble Arises
Battery Runs Out
7-41

xRepeatedly jerking the steering
wheel left and right while the vehicle
is stopped or moving extremely
slowly will cause the power steering
system to go into protective mode
which will make the steering feel
heavy, but this does not indicate a
problem. If this occurs, park the
vehicle safely and wait several
minutes for the system to return to
normal.
▼ABS Warning Indication/Warning
Light
If the ABS warning light stays on while
you're driving , the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
NOTE
xWhen the engine is jump-started to
charge the battery, uneven rpm
occurs and the ABS warning light
may illuminate. If this occurs, it is the
result of the weak battery and does
not indicate an ABS malfunction.
Recharge the battery.
xThe brake assist system does not
operate while the ABS warning light
is illuminated.
▼Master Warning Indication
The indication displays if the system
has a malfunction.
Check the reason for the indication
displaying on the centre display or
multi-information display.
Refer to If a Warning Light Turns On or
Flashes on page 7-49.
▼Brake Control System Warning
Indication/Warning Light (Amber)
The warning light illuminates when the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
▼Electric Parking Brake (EPB)
Indication/Indicator Light
This warning has the following
functions:
Parking brake warning/Indicator light
inspection
The light illuminates when the parking
brake is applied with the ignition
switched to START or ON. It turns
off
when the parking brake is released.
When the light is
flashing
The light flashes if the Electric Parking
Brake (EPB) has a malfunction. If the
light remains flashing even if the
Electric Parking Brake (EPB) switch is
operated, consult an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-52

▼Brake Override Warning Indication
This message is displayed when the
accelerator pedal and brake pedal are
depressed at the same time while
driving.
Release the accelerator pedal and
depress the brake pedal.
▼Check Engine Indication/Light
If this light illuminates while driving ,
the vehicle may have a problem. It is
important to note the driving
conditions when the light illuminated
and consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
The check engine light may illuminate
in the following cases:
xThe engine's electrical system has a
problem.
xThe emission control system has a
problem.
x(Except SKYACTIV-D 1.8)
xThe fuel tank level being very low
or approaching empty.
xThe
fuel-filler cap is missing or not
tightened securely.
If the check engine light remains on, or
it flashes continuously , do not drive at
high speeds and consult an expert
repairer (we recommend an
Authorised Mazda Repairer) as soon as
possible.
WARNING
If the check engine light turns on, do
not disconnect the battery leads.
If the battery leads are disconnected
and then reconnected, the engine
could be damaged and catch on
fire.
▼i-stop Warning Indication/
Warning Light (Amber)*
When the light is turned on
xA problem in the system may be
indicated under the following
conditions. Have your vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
xThe light does not turn on when
the ignition is switched ON.
x(Except European model)
If the i-stop warning light (amber)
remains on while the engine is
running , the battery performance
may have decreased. Have your
vehicle inspected at an expert
repairer (we recommend an
Authorised Mazda Repairer).
When the light is flashing
The light continues to flash if the
system has a malfunction. Have your
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer).
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-53

▼KEY Warning Indication/Warning
Light (Red)
“Keyless Entry System Malfunc. Have
the Vehicle Inspected” is displayed
This message is displayed if the
advanced keyless entry & push button
start system has a problem.
Contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
CAUTION
If the message is indicated, or the push
button start indicator light (amber)
flashes, the engine may not start. If the
engine cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an expert repairer
(we recommend an Authorised Mazda
Repairer) as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-9.
“Key Not Detected” is displayed
xIf the presence of the key cannot be
detected (dead battery, battery
malfunction, no key), it is displayed
when the driver attempts to start the
engine (push button start operation,
brake pedal depression).
xDisplayed when it is determined that
a key that was in the vehicle has
been removed from the vehicle. (Key
taken out warning. Other than
IG-OFF).
▼Security Indicator Light
If the security indicator light flashes
continuously while you are driving, do
not shut
off the engine. Go to an
expert repairer (we recommend an
Authorised Mazda Repairer) and have
it checked. If the engine is shut off
while the indicator light is
flashing , you
will not be able to restart it.
Make sure the key is within the
operational range for signal
transmission. Switch the ignition off,
and then restart the engine. If the
engine does not start after 3 or more
tries, contact an expert repairer (we
recommend an Authorised Mazda
Repairer).
NOTE
Because the electronic codes are reset
when the immobilizer system is
repaired, the keys are needed. Make
sure to bring all the keys to an
Authorised Mazda Repairer so that
they can be programmed.
▼AWD Warning Indication/
Warning Light*
“AWD Malfunction. Front Wheel
Drive Only. Have the Vehicle
Inspected” is displayed/When the
light is turned on
The indication is displayed/the light
turns on under the following
conditions. The system may have a
malfunction. Have the vehicle checked
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-56*Some models.