2018 YAMAHA YZF-R1M Owners Manual

Instrument and control functions
4-19
1
2
345
6
7
8
9
10
11
12
mark to fine tune the ERS mode
settings.
ERS (YZF-R1M)
The ERS consists of three semi-active
automatic modes (T-1, T-2, R-1) and
three manual setting modes (M-1, M-2,
M-3). When an automatic mode is se-
lected, the SCU will adjust the com-
pression and rebound damping forces
based on running conditions. For all modes and models, spring preload is
physically adjusted by hand. (See pag-
es 4-41 and 4-44.)
For track modes T-1 and T-2, the fol-
lowing settings can be adjusted:
BRAKE SUPPORT: reduces nosedive
(front-end pitch from braking)
CORNER SUPPORT: increases
damping to absorb c
hassis fluctuations
for smooth cornering. Reduce this set-
ting for increased rear wheel grip.
ACCEL SUPPORT: reduces rear-end
squat (rear-end pitch due to accelera-
tion)
FRONT FIRM: hardens (H) or softens
(S) overall damping of the front suspen-
sion
REAR FIRM: hardens (H) or softens
(S) overall damping of the rear suspen-
sion For the road mode R-1, the following
settings can be adjusted:
BRAKE SUPPORT: reduces nosedive
(front-end pitch from braking)
FRONT FIRM: hardens (H) or softens
(S) overall damping of the front suspen-
sion
REAR FIRM: hardens (H) or softens
(S) overall damping of the rear suspen-
sion
TIP
T-1 is preset for track use with rac-
1. ERS mode selection box “SETTING”
2. Braking support level
3. Cornering support level
4. Acceleration support level
5. Front overall damping level
6. Rear overall damping level
7. Factory preset level
8. Offset level
SETTING
BRAKE
SUPPORT CORNER
SUPPORT
ACCELSUPPORT
FRONT FIRM REAR
FIRM
12 :
00
YRC Setting
km/hT -
1
H -2
S H
+2
S
T -
2
R -
1134 8
5 7
6
2
1. ERS mode selection box “SETTING”
2. Braking support level
3. Front overall damping level
4. Rear overall damping level
5. Factory preset level
6. Offset level
SETTING
BRAKE
SUPPORT
FRONT
FIRM REAR
FIRM
12 :
00
YRC Setting
km/hR -
1
H -2
S H
+2
S
T -
1
T -
213 4
2
6
5
BX4-9-E1_1.book 19 ページ ２０１８年４月２７日　金曜日　午後４時３分

Instrument and control functions
4-20
1
2
34
5
6
7
8
9
10
11
12 ing slick tires.

T-2 is preset for track use with
street tires.

R-1 is preset for road use withstreet tires.
For the manual setting modes M-1,
M-2, and M-3, the following settings
can be adjusted:
Fr COM: front compression damping
Fr REB: front rebound damping
Rr COM: rear compression damping Rr REB: rear rebound damping
TIP
M-1 is preset for track use with rac-
ing slick tires.

M-2 is preset for track use with
street tires.

M-3 is preset for street use withstreet tires.
To adjust the ERS mode settings
1. Select the “ ” mark located to the right of ERS.TIPThe ERS setting menu is divided into
automatic and manual setting modes,
and the two types are accessed sepa- rately. Before moving to the ERS set-
ting menu, make sure the current ERS
mode corresponds to the same type
(automatic or manual) that you'd like to
adjust.
2. The display will change to the rele- vant suspension setting screen
and the ERS mode selection box
“SETTING” is highlighted. Short
push the wheel switch to enter the
box and select the ERS mode that
you want to adjust.
3. Select the suspension item that you want to adjust, and then rotate
the wheel switch to adjust the set-
ting level.TIPAll ERS modes regardless of type are
independent and should be set sepa-rately.
4. To adjust other ERS modes of the same type, repeat from step 1. To
switch types or when finished, se-
lect the “ ” mark to return to the
main “YRC Setting” menu.
1. ERS mode selection box “SETTING”
2. Front compression damping force
3. Front rebound damping force
4. Rear compression damping force
5. Rear rebound damping force
6. Factory preset level
7. Current level setting
12 :
00
YRC Setting
km/hM -
1
M -
2
M -
3
Fr COM Rr COM
Fr REB Rr REB
SETTING
18
8 22 22
134 7
5 6
2
1. To ERS menu
YRC
PWRTCS SCS LCS QS
LIF
ERS
12:
00
YRC Setting
km/h
QS
A 1
5 2 1
111 1
ON
1
OFF
1
T-
1
4 3 3 22
OFF
2OFF
3
2OFF
OFF
3
2
4
C B
D 1
T-
2
R -
1
M -
1
M -
2
1
BX4-9-E1_1.book 20 ページ ２０１８年４月２７日　金曜日　午後４時３分

Instrument and control functions
4-21
1
2
345
6
7
8
9
10
11
12
“Lap Time”
This module allows you to view and de-
lete the lap time record. The fastest lap
and the average lap time stored in the
lap time record are displayed at the top
of the screen. Use the wheel switch to
scroll and see all lap times. The top
three fastest laps will be highlighted in
silver. Up to 40 laps can be stored in
memory. If more than 40 laps are re-
corded, the oldest laps (starting from
lap 1) will be overwritten.
This module has two options.
“Display” allows you to view the lap
time record. “Reset” allows you to delete the lap
time record data.
Use the wheel switch to select “Display”
and view the lap record.
To reset the lap time record data
1. When “Lap Time” is selected, both
“Display” and “Reset” are dis-
played.
2. Select “Reset”.
3. Select YES to delete all lap time data. (Select NO to exit and return
to the previous screen without re-
setting the lap record.)
1. To YRC Setting menu
2. Factory preset level
3. Current level setting
12 :
00
YRC Setting
km/hM -
1
M -
2
M -
3
Fr COM Rr COM
Fr REB Rr REB
SETTING
18
8 22 22
2 3
1
1. Fastest lap
2. Average lap time
3. Lap time record
km/h
12
:
00
Reset
Display
Lap Time
LAP 1LAP 2LAP 3LAP 4 FA
STEST / LAP 12
02:54.56
02:55.20
02:56.04
02:56.80 02:34.56
02:53.00
AVERAGE
Lap Time
km/h
GP GPS
12:
00
123
km/h
12 :
00
Reset
Display
Lap Time
km/h
12
:
00
Reset
Display
Lap Time
BX4-9-E1_1.book 21 ページ ２０１８年４月２７日　金曜日　午後４時３分

Instrument and control functions
4-22
1
2
34
5
6
7
8
9
10
11
12 “Logging” (CCU-equipped models)
Vehicle and riding information can be
recorded (logged) and this data can be
accessed with a smart device (see
“CCU” on page 4-39).
To start and stop logging
1. From the MENU screen, select
“Logging”.
TIPIf a CCU is not installed, then the “Log-ging” module cannot be selected.
2. Select START to start logging.
3. To stop the “Logging” function, se- lect STOP or turn the vehicle off. “Maintenance”
This module allows you to record dis-
tance traveled between engine oil
changes (use the OIL item), and for two
other items of your choice (use INTER-
VAL 1 and INTERVAL 2).
To reset a maintenance item
1. From the MENU screen, select
“Maintenance”.
2. Select the item you want to reset.
NO
Reset ?Lap Time
YES
km/h
GPGPS
12:
00
YRC Setting
Lap TimeLogging
Maintenance
Unit
Display ModeMENU
km/h
GPS
12
:
00
1. Logging indicator
STOP
STARTLogging
km/h
12
:
00
GPS
1
STOP
STARTLogging
km/h
12
:
00
GPS
YRC Setting
Lap TimeLogging
Maintenance
Unit
Display ModeMENU
km/h
GPS
12
:
00
BX4-9-E1_1.book 22 ページ ２０１８年４月２７日　金曜日　午後４時３分

Instrument and control functions
4-23
1
2
345
6
7
8
9
10
11
12
3. Long push the wheel switch to re-
set the item.
TIPMaintenance item names cannot bechanged.
“Unit”
This module allows you to switch the
display between kilometers and miles. When using kilometers, the fuel con-
sumption units can be changed be-
tween km/L or L/100km. When using
miles, MPG will be available.
To set the distance or fuel consumption
units1. From the MENU screen, select
“Unit”.
2. “km or mile” and “km/L or L/100km” are displayed. 3. Select the distance or consump-
tion unit item you want to adjust.
4. Select the units you want to use.
INTERVAL 2 OIL
INTERVAL 1
123456 km
123456 km
123456 km
Maintenance
km/h
GPS
12 :
00
INTERVAL 2 OIL
INTERVAL 1
0 km
123456 km
123456 km
Maintenance
km/h
GPS
12 :
00
YRC Setting
Lap TimeLogging
Maintenance
Unit
Display ModeMENU
km/h
GPS
12
:
00
km/L or L/100km km/Lkm or mile km
Unit
km/h
GPGPS
12:
00
km/L or L/100km km/Lkm or mile km
Unit
km/h
GP GPS
12:
00
BX4-9-E1_1.book 23 ページ ２０１８年４月２７日　金曜日　午後４時３分

Instrument and control functions
4-24
1
2
34
5
6
7
8
9
10
11
12 5. Select the triangle symbol to exit.
“Wallpaper”
This module allows you to individually
set the STREET MODE and TRACK
MODE display background colors to
black or white for both day and night
settings. A photo sensor equipped in
the instrument panel detects lighting
conditions and will automatically
change the display between its day and
night settings. The photo sensor also
controls a subtle automatic brightness
adjustment function within both day
and night modes to suit ambient light
conditions. To set the wallpaper
1. From the MENU screen, select
“Wallpaper”.
2. Select the mode you want to adjust (select DAY for daytime display
settings or NIGHT for nighttime
display settings). 3. Select the background color (se-
lect BLACK for a black background
or WHITE for a white background).
4. Select the triangle symbol to exit.
5. To set another background color, repeat from step 2 or select the tri-
angle symbol to exit this module.
“Shift indicator”
The shift indicator module contains the
km/L or L/100km km/Lkm or mile km
Unit
km/h
GPGPS
12:
00
1. Photo sensor
1
GP GPS
TRACK MODE (day)
STREET MODE (night)
TRACK MODE (night) Wallpaper
STREET MODE (day)
km/h
12 :
00
WHITEBLACK
Wallpaper
STREET MODE (day)
km/h
GPGPS
12 :
00
GP GPS
TRACK MODE (day)
STREET MODE (night)
TRACK MODE (night) Wallpaper
STREET MODE (day)
km/h
12 :
00
BX4-9-E1_1.book 24 ページ ２０１８年４月２７日　金曜日　午後４時３分

Instrument and control functions
4-25
1
2
345
6
7
8
9
10
11
12
following modules.
To make setting changes
1. Select “Shift IND Setting”.
2. Select “IND Mode”. 3. Select “ON” to have the indicator
light steadily, “OFF” to turn the in-
dicator off, or “Flash” to have the
shift indicator flash when the indi-
cator start threshold has been
reached.
4. Select “IND Start”. 5. Rotate the wheel switch to adjust
the r/min at which the shift timing
indicator light will come on. “IND
Start” operational range is
8000–14800 r/min.
6. Select “IND Stop” then rotate the wheel switch to adjust the r/min at
which the shift timing indicator will
go off. “IND Stop” operational
Module Description
Set the shift indicator
pattern to “ON”, “Flash”,
or “OFF” and adjust at
what r/min the indicator
will come on and go off.
Adjust the brightness of
the shift indicator.
Set the tachometer color
display to “ON” or “OFF”
and adjust at what r/min
the tachometer will be
green and orange.
Set the tachometer peak
rev indicator to “ON” or
“OFF”.Shift IND SettingShift IND
BrightnessTach IND SettingPeak Rev IND Setting
GP GPS
Tach IND Setting
Shift IND Brightness
Peak Rev IND Setting Shift Indicator
Shift IND Setting
km/h
12 :
00
Shift Indicator
km/h
x 1000 r/min
GPS
12 :
00
Shift IND Setting
IND Mode
IND Start
IND Stop ON
10000
r/min
15000
r/min
Shift Indicator
km/h
x 1000 r/min
GPS
12 :
00
Shift IND Setting
IND Mode
IND Start
IND Stop ON
10000
r/min
15000
r/min
Shift Indicator
km/h
x 1000 r/min
GPS
12 :
00
Shift IND Setting
IND Mode
IND Start
IND Stop ON
10000
r/min
15000
r/min
Shift Indicator
km/h
x 1000 r/min
GPS
12 :
00
Shift IND Setting
IND Mode
IND Start
IND Stop ON
10000
r/min
15000
r/min
BX4-9-E1_1.book 25 ページ ２０１８年４月２７日　金曜日　午後４時３分

Instrument and control functions
4-26
1
2
34
5
6
7
8
9
10
11
12 range is 8500–15000 r/min.
TIPThe blue area on the tachometer indi-
cates the currently set operationalrange of the shift indicator light.
“Shift IND Brightness”
The shift timing indicator light has six
brightness levels.
Select “Shift IND Brightness”, then use
the wheel switch to adjust the setting.
Short push the wheel switch to confirm
the setting and exit.
“Tach IND Setting”
This module allows you to turn the ta-
chometer color display on or off. When
turned off, the tachometer will display
all r/min levels below the red zone in
black or white (depending on wallpaper
settings). When turned on, the mid and
mid-to-high r/min zones can be set to
come on in green and then orange col-
ors.
1. Select “Tach IND Setting”.
2. Select “IND Mode”.
GP GPS
Tach IND Setting
Shift IND Brightness
Peak Rev IND Setting Shift Indicator
Shift IND Setting
km/h
12 :
00
Shift Indicator
Shift IND Brightness
km/h
GPS
12 :
00
3
GPGPS
Tach IND Setting
Shift IND Brightness
Peak Rev IND Setting Shift Indicator
Shift IND Setting
km/h
12 :
00
Shift Indicator
km/h
x 1000 r/min
GPS
12 :
00
Tach IND Setting
IND Mode ON
8000
r/min
11000
r/min
Tach IND 1st
Tach IND 2nd
BX4-9-E1_1.book 26 ページ ２０１８年４月２７日　金曜日　午後４時３分