Page 41 of 136
39
Charge programming
Warning/
indicator lampStateCauseAction/Observations
Flash for a few seconds. The charging cable is not connected
properly.Check the cable.
There is a problem with your electrical
installation. Have it checked by a qualified electrician.
Flashes for a few seconds. The drive selector is not in position P. Place the drive selector in position P .
Thermal comfort programming
Warning/
indicator lampState CauseAction/Observations
Flash for a few seconds. The charging cable is not connected
properly.Check the cable.
There is a problem with your electrical
installation. Have it checked by a qualified electrician.
Flash for a few seconds. The main battery is not sufficiently
charged.Charge the battery and start the
programming again.
Flashes for a few seconds. A vehicle door is still open.Close all the doors and start the
programming again.
The drive selector is not in position P . Place the drive selector in position P .
3
Ease of use and comfort
Page 42 of 136

40
Lighting control stalk
Main lighting
The various front and rear lamps of the vehicle
are designed to adapt the lighting gradually to
the climatic conditions and thus give the driver
better visibility:
-
s
idelamps, to be seen,
-
d
ipped beam headlamps to see without
dazzling other drivers,
-
m
ain beam headlamps to see clearly when
the road is clear.
Additional lighting
Other lamps are fitted to meet particular driving
conditions:
-
a r
ear foglamp to be seen from afar,
-
f
ront foglamps for even greater visibility,
-
d
aytime running lamps to be seen during
t h e d ay.
Selection ring for main
lighting mode
Turn it to align the desired symbol with the
mark.
Dipped or main beam headlamps.
Sidelamps.
Automatic illumination of headlamps.
Lighting off.
Headlamp dipping stalk
Pull the stalk to switch the lighting between
dipped/main beam headlamps.
In the lighting off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk.
Displays
Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Lighting and visibility
Page 43 of 136

41
Front and rear foglamps
Foglamps selection ring.
They operate with the sidelamps and dipped or
main beam headlamps.Front and rear foglamps:
F
T
urn the ring for wards once to switch on the
front foglamps.
F
T
urn the ring for wards twice to switch on the
rear foglamp.
F
T
urn the ring backwards once to switch off
the rear foglamp.
F
T
urn the ring backwards twice to switch off
the front foglamps. It is prohibited to switch on the front or
rear foglamps in fine weather or in rain,
night or day. In these situations, the power
of their beams may dazzle other drivers.
Do not forget to switch off the front
foglamps and the rear foglamp when they
are no longer necessary.
When lighting is left on
When the driver's door is opened, with the
ignition off, an audible signal warns the
driver that the vehicle's lighting is left on.
In this case, switching off the lighting
stops the audible signal.
Direction indicators
(flashing)The ring automatically returns to its initial
position.
The rear foglamp switches off automatically
when you switch off the sidelamps and dipped
or main beam headlamps.
F
L
eft: lower the lighting control stalk passing
the point of resistance.
F
R
ight: raise the lighting control stalk passing
the point of resistance.
Daytime running lamps
Specific daytime lighting to make the vehicle
more visible.
The daytime running lamps light up
automatically when the engine starts if no other
lamps are on.
They cannot be deactivated.
Although these lamps are located in the
same lamp unit as the front foglamps, they
operate with a specific bulb.
Their use complies with the Highway
Code.
4
Lighting and visibility
Page 44 of 136

42
Automatic illumination/
switching off of the headlamps
Automatic illumination
When the lighting control stalk ring is in
the AUTO position, the sidelamps and
dipped beam headlamps are switched on
automatically, without any action on the part of
the driver, when a low level of ambient light is
detected.
As soon as the level of light becomes sufficient
again, the lights are switched off automatically.
The sensor is located at the bottom of the
windscreen.
Do not cover the sunshine sensor, as the
associated functions would no longer be
controlled.
In fog or snow, the sunshine sensor may
detect sufficient light. The headlamps may
not come on automatically.
Automatic switching off
When the lighting control stalk is in the "AUTO"
position, if the ignition key is in the "LOCK" or
"ACC" position or is removed, the headlamps
will automatically switch off when the driver's
door is opened .
Headlamp beam height
adjustment
To avoid causing a nuisance to other road
users, the height of the halogen headlamp
beams must be adjusted according to the load
in the vehicle.
0.Driver only or driver + 1 front
passenger.
1 or 2. 4 passengers (including driver).
3. 4 passengers (including driver) +
maximum authorised load.
4. Driver + maximum authorised load.
The initial setting is position " 0".
Wiper control stalk
The wipers are controlled directly by the driver
using control A and ring B .
In wintry conditions, remove snow, ice
or frost present on the windscreen,
around the wiper arms and blades and
the windscreen seal before operating the
wipers.
Do not operate the wipers on a dry
windscreen. Under extremely hot or cold
conditions, ensure that the wiper blades
are not stuck to the windscreen before
operating the wipers.
Lighting and visibility
Page 45 of 136

43
Windscreen wipers
A.Wiping speed control lever: raise
or lower the lever to the desired
position.
Single wipe.
Of f.
Intermittent (manually adjustable
speed).
Slow.
Fast.
B. Intermittent adjustment ring.
F
T
urn this ring to increase or
decrease wiping frequency in
intermittent mode.
Front screenwash
Pull the wiper control stalk towards you. The
screenwash and then the wipers operate for a
preset time.
Rear wiper
C. Rear wiper selection ring.
Of f.
Intermittent wiping.
The wiper wipes twice then switches to
intermittent mode with an inter val of a few
seconds. Wash-wipe.
Hold the ring in this position to operate the
screenwash and to carry out several wipes with
the wipers.
Courtesy lamp
Position 1 "ON"
The courtesy lamp is permanently on.
Position 2 "●"
The courtesy lamp comes on when a door or
the boot is opened; when the door or boot is
closed again, the lighting dims gradually for a
few seconds before going out.
However, the courtesy lamp goes out
immediately when the doors and boot are
closed and you lock the vehicle from the inside
or with the remote control.
4
Lighting and visibility
Page 46 of 136
44
Before leaving the vehicle, check that the
courtesy lamp is not still on.
If it remains permanently on, it will
discharge the ancillaries battery even if
the main battery is charged or charging.
It will then no longer be possible to start
the vehicle.
Position 3 "OFF"
The courtesy lamp is permanently off.
Lighting and visibility
Page 47 of 136

45
General safety
recommendations
Labels are attached in different places on
your vehicle. They include safety warnings
as well as identification information for
your vehicle. Do not remove them: they
are an integral part of your vehicle.
For any work on your vehicle, use a
qualified workshop that has the technical
information, skills and equipment required,
all of which a PEUGEOT dealer is able to
provide.We draw your attention to the following
points:
-
T
he fitting of electrical equipment
or accessories not listed by
PEUGEOT may cause excessive
current consumption and faults and
failures with the electrical system of
your vehicle. Contact a PEUGEOT
dealer for information on the range of
recommended accessories.
-
A
s a safety measure, access to
the diagnostic socket, used for the
vehicle's electronic systems, is
reser ved strictly for PEUGEOT dealers
or qualified workshops, equipped
with the special tools required (risk
of malfunctions of the vehicle's
electronic systems that could cause
breakdowns or serious accidents).
The manufacturer cannot be held
responsible if this advice is not
followed.
-
A
ny modification or adaptation not
intended or authorised by PEUGEOT
or carried out without meeting the
technical requirements defined by
the manufacturer will result in the
suspension of the legal and contractual
warranties. Installation of accessory radio
communication transmitters
Before installing a radio communication
transmitter, you must contact a PEUGEOT
dealer for the specification of transmitters
which can be fitted (frequency, maximum
power, antenna position, specific
installation requirements), in line with the
Vehicle Electromagnetic Compatibility
Directive (2004/104/EC).
Depending on country regulations, some
safety equipment may be compulsory:
high visibility safety vests, warning
triangles, breathalysers, spare bulbs,
spare fuses, fire extinguisher, first aid kit,
mud flaps at the rear of the vehicle, etc.
5
Safety
Page 48 of 136

46
Hazard warning lamps
F When you press this red button, all four direction indicators flash.
They can operate with the ignition off.
Brake lamps, automatic
operation
The brake lamps may light up automatically
when you release the accelerator pedal.
Their illumination is not systematic and
depends on the rate of deceleration.
Horn for pedestrians
(Depending on equipment.)
System to alert pedestrians to the presence of
the vehicle.
When the vehicle is started, illumination of
the button indicator lamp for a few seconds
indicates system activation.
Operation
Horn
F Press the central part of the steering wheel. The horn sounds when the vehicle speed is
between 0 and 22
mph (35 km/h),
Deactivation
In certain driving conditions you can deactivate
the system.
Press this button.
The button indicator lamp comes on and the
audible signal stops.
Another press reactivates the system.
The button indicator lamp goes off. Before deactivating the system, make
sure that you are not driving in an area
frequented by pedestrians.
The system is reactivated automatically at
every new start.
Malfunction
The button indicator lamp flashes if the system
malfunctions. Contact a PEUGEOT dealer
or a qualified workshop to have the system
checked.
Safety