2018 Peugeot iOn engine

49
The warning lamp comes on for a few
seconds when switching on (ON position).
If it does not go out or come on, contact a
PEUGEOT dealer or a qualified workshop.
Moving vehicle If this warning lamp remains on
constantly, it indicates an anti-lock
braking system malfunction that
could cause control of the vehicle to
be lost during braking.
You must stop as soon as it is safe to do so.
Contact a PEUGEOT dealer or a qualified
workshop.
If both these warning lamps come
on, they indicate a malfunction in the
electronic brake force distribution
that could cause control of the
vehicle to be lost during braking.
You must stop as soon as it is safe to do so.
Contact a PEUGEOT dealer or a qualified
workshop.
When replacing wheels (tyres and rims),
ensure that they comply with manufacturer
recommendations.Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure more
quickly, thus reducing the stopping distance.
Activation
It is triggered by the speed at which the brake
pedal is pressed.
The effect of this is a reduction in the
resistance of the pedal and an increase in
braking efficiency. In emergency braking, press very firmly
and maintain this pressure.
Trajectory control systems
Anti-slip regulation (ASR)
and dynamic stability
control (DSC)
The anti-slip regulation (also known as traction
control) optimises traction to prevent skidding of
the wheels, by acting on the brakes of the driving
wheels and on the engine.
The stability control acts on the brake of one
or more wheels and on the engine to keep the
vehicle on the trajectory required by the driver,
within the limits of the laws of physics.
Activation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of a
problem with grip or trajectory. This is indicated by flashing of this
warning lamp in the instrument
panel.
Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
the ASR and DSC systems, so that the wheels
can regain grip.
F

P
ress this button until the corresponding
symbol appears in the instrument panel.
The display of this symbol indicates
that the ASR and DSC systems are
deactivated.
5
Safety

50
Excessive wheel slippage may damage
the differential of your vehicle.
Reactivation
These systems are not reactivated
automatically.
F
P
ress the button again to reactivate them
manually.
The symbol going off in the instrument panel
indicates reactivation of the ASR and DSC
systems.
Operating fault
Illumination of these warning lamps
in the instrument panel indicates
malfunction of these systems.
Contact a PEUGEOT dealer or a qualified
workshop to have the ASR /DSC systems
checked. Although the ASR /DSC systems help
improve safety in normal driving, they
should not encourage the driver to take
extra risks or drive at high speed.
The risk of loss of traction increases in
conditions of reduced grip (rain, snow,
ice). For your safety, you should therefore
keep these systems activated at all times,
particularly in poor conditions.
The correct operation of these systems
depends on observing the manufacturer's
recommendations regarding wheels (tyres
and rims), braking system components
and electronic components, as well as
assembly and repair procedures used by
the PEUGEOT dealer network.
After an impact, have these systems
checked by a PEUGEOT dealer or a
qualified workshop.
Engine brake reduction
indicator lamp
Your vehicle is equipped with a system for the
recovery of energy during deceleration which
uses the engine brake.
It recovers into the traction battery some of the
energy generated when the vehicle slows down
(e.g. on a long descent) to improve the range
of the battery and so the distance that can be
travelled between charges.
When the traction battery has been charged
fully and for the first few miles (or kilometres) of
use of the vehicle, the engine brake is reduced
temporarily.
This indicator lamp flashes on the
instrument panel, inviting you to
adapt your driving accordingly.
We therefore recommend that you anticipate
your braking as much as possible: use the
brake pedal to slow down or stop the vehicle.
Safety

68
Driving recommendations
Observe the driving regulations and remain
vigilant whatever the traffic conditions.
Pay close attention to the traffic and keep your
hands on the steering wheel so that you are
ready to react at any time to any eventuality.
As a safety measure, the driver must only carry
out any operations that require close attention
when the vehicle is stationary.
On a long journey, a break every two hours is
strongly recommended.
In bad weather, drive smoothly, anticipate the
need to brake and increase the distance from
other vehicles.
Important!
Never drive with the parking brake applied – Risk of overheating and damage to the
braking system!
Never leave a vehicle unsuper vised with
the motor running. If you have to leave
your vehicle with the motor running,
apply the parking brake and put the drive
selector into position N or P.
Driving on flooded roads
We strongly advise against driving on flooded
roads, as this could cause serious damage
to the motor or gearbox, as well as to the
electrical systems of your vehicle.
If you are obliged to drive through water:
-

c
heck that the depth of water does not
exceed 6 inches (15
cm), taking account
of waves that might be generated by other
users,
-

d
rive as slowly as possible. In all cases, do
not exceed 6
mph (10 km/h).
On leaving the flooded road, as soon as
circumstances allow, make several light brake
applications to dry the brake discs and pads.
If in doubt about the state of your vehicle,
contact a PEUGEOT dealer or a qualified
workshop.
Starting-switching off the
vehicle
Ignition switch
- Position 1: LOCK .
The steering is locked.
-

P
osition 2: ACC .
The accessories (audio system, 12V socket,
etc.) can be used.
-

P
osition 3: ON .
Switching on the ignition.
-

P
osition 4: S TA R T .
"Ready" lamp lights up.
Engine operation.
If you use accessories for a prolonged
period of time (with the switch in position
ACC ), you risk discharging the ancillaries
battery. Starting your vehicle will then no
longer be possible. Be careful.
Driving

70
Starting the vehicle
With the engine running, P appears on the
instrument panel display screen.
F
P
ress the brake pedal to exit position P .
F

S
elect for ward drive ( D) or reverse ( R).
F

R
elease the parking brake.
Switching off the vehicle
To switch off the engine, select position P .
You must without fail apply the parking brake to
immobilise the vehicle.
To remove the key from the ignition, the drive
selector must be in position P .
To tow your vehicle, the drive selector
must be in position N .
For more information on Towing the
vehicle , refer to the corresponding
section.
Tyre under-inflation
detection
System which automatically checks the
pressures of all four tyres from when the
ignition is switched on.
The pressure sensors are located in the valves
of each tyre.
The system triggers an alert as soon as
it detects a drop in the pressure of one or
more tyres by comparison with the reference
pressure stored in the system. This reference
pressure must be reinitialised after every tyre
pressure adjustment or wheel change.
The system operates provided that the
sensor identifiers have been first logged by a
PEUGEOT dealer or a qualified workshop.
You can log two sets of tyres (for example:
wheels with "all weather" tyres and wheels with
"winter" tyres).
The tyre under-inflation detection system
is a driving aid which does not replace the
need for vigilance on the part of the driver.
F Take your foot off the brake pedal, and the vehicle will move at a low speed to make
manoeuvring easier.
F

A
ccelerate to move for ward or backward.
F
"D " or " R" appears on the instrument panel
display screen.
Driving

82
During fast charging, the vehicle's air
conditioning may start up automatically,
if necessary, to cool the main battery. It
is therefore completely normal to hear
a ventilation noise from the exterior and
to see a puddle of water form under the
vehicle.
Fast charging stops automatically when
the main battery is about 80% charged. It
is possible to achieve a 100% charge by
starting the procedure again. However, the
time required to complete the charge will
be relatively long, as the charging speed
will have slowed down.
The charging warning lamp in the instrument panel
going off indicates that charging is complete.
F Disconnect the charging cable following the instructions for use of the charging point.
F

C
lose the socket cover, then the access
flap.
As a safety measure, the engine will
not start when the charging cable is
connected to the vehicle's socket.
In addition, any attempt to start during
charging will interrupt the procedure. It will
be necessary to disconnect and reconnect
the charging cable to the vehicle's
socket and then to begin charging again,
following the instructions for use of the
charging point. After recharging, ensure that the socket
cover and access flap are closed.
Take care to avoid allowing water or
dust to enter the socket, under its cover
or in the charging plug (risk of fire or
electrocution).
If the exterior temperature is below 0°C,
charging times may be longer.
If the exterior temperature is below -25°C,
charging may not be possible.
Immobilising the vehicle for a long
period
When your vehicle is to be immobilised
for an indeterminate period, carry out
a complete charge of the main battery
every three months (following the normal
charging procedure).
Before carrying out the charging
operation, ensure that the ancillaries
battery is not disconnected or discharged.
For more information on the ancillaries
battery
, refer to the corresponding
section.
Snow chains
The snow chains must be fitted only to the rear
wheels (rear wheel drive car).
Take account of the legislation in force in
your country on the use of snow chains
and the maximum authorised speed.
Installation tips
F If you have to fit the chains during a journey, stop the vehicle on a flat sur face on the side
of the road.
F

A
pply the parking brake and if necessary
put wheel chocks against the wheels to
prevent your vehicle from sliding.
F

F
it the chains following the instructions
provided by the manufacturer.
F

M
ove off gently and drive for a few seconds,
without exceeding 30
mph (50 km/h).
F

S
top your vehicle and check that the snow
chains are correctly tightened.
It is strongly recommended that before
you leave, you practise fitting the snow
chains on a level and dry sur face.
Practical information

89
F Connect one end of the red cable to the (+ ) terminal of the flat battery A , then the
other end to the ( +) terminal of the back-up
battery
B .
F
C
onnect one end of the green or black
cable to the (-) terminal of the back-up
battery B .
F

C

onnect the other end of the green or black
cable to the earth point C of your broken
down vehicle. F

S
tart the engine of the vehicle with the good
battery and wait for a few minutes.
F
O
perate the ignition switch of your vehicle
until the "Ready" lamp comes on.
F
D
isconnect the jump cables in reverse
o r d e r.
F
R
efit the protective cover on the battery and
tighten the retaining nut.
If the "Ready" warning lamp does not come on,
proceed as follows:
F
L
eave the cables connected.
F
S
et the ignition switch of your vehicle to the
" LOCK " position.
F
C
harge the main battery, following the
normal charging procedure.
F
W
hen the charging indicator lamp comes on
constantly (fixed) in the instrument panel,
disconnect the cables.
F
A
llow the charging to continue for at least
o n e h o u r.
F
O
perate the ignition switch of your vehicle
until the "Ready" lamp comes on.
If the problem persists, contact a PEUGEOT
dealer or a qualified workshop.
Charging the battery using
a battery charger
F Remove the battery protective cover.
Make sure the electrolyte is not frozen.
Check the level and top up with distilled
water, if necessary.
For more information on Checking levels ,
refer to the corresponding section.
F

U
nscrew nut 1 and remove the retaining
clip.
8
In the event of a breakdown

105
Towing the vehicle
Procedure for having your vehicle towed using
a fixed towing eye.General recommendations
Obser ve the legislation in force in your
c o u nt r y.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing arm; rope and straps are
prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
In the following cases, you must always
call on a professional recovery ser vice:
-

v
ehicle broken down on a motor way or
main road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox into neutral, to unlock the
steering, or to release the parking
brake,
-

t
owing with only two wheels on the
ground,
-

w
here there is no approved towbar
available.
Towing your vehicle
The towing eye is welded to the chassis under
the front bumper.
F

I
nstall the towbar.
F

S
tart your vehicle ("Ready" lamp on).
F

M
ove the drive selector to position N .
F

R
elease the parking brake.
F

T
urn on your vehicle's hazard warning
lamps.
F

H
ave your vehicle towed for no more than
20
miles (30 km) without exceeding the
speed of 20
mph (30 km/h).
Failure to comply with these operations
may cause damage to the braking
components and the electric motor.
Towing another vehicle
Your vehicle cannot in any circumstances
be used to tow another vehicle.
8
In the event of a breakdown

1
Bluetooth® audio system
Contents
First steps
1
R

adio 2
Media

3
T

elephone

6
Audio settings
8
C

onfiguration

8
Frequently asked questions

9
F

or safety reasons, the vehicle must
always be stationary for the driver to
perform operations that require close
attention.
When the engine is switched off and to
prevent discharging of the battery, the
system switches off after activation of
energy economy mode. After a battery disconnection, a code must
be entered to access the audio system
functions.
You can try five times at most. There is
approximately fifteen minutes waiting time
between each of the last two tries.
Go to the end of this document to recover
the label indicating the code:
First steps
On/Off, volume adjustment.
Adjust audio options: sound
ambience, treble, bass, loudness,
distribution, left/right balance, front/
rear balance, automatic volume.
Automatic search for a lower radio
frequency.
Select the previous CD, USB track.
Scroll in a list.
Press and hold: rewind.
Display the list of stations received,
the CD/USB tracks or folders.
Press and hold: update the list of
stations received.
Cancel the current operation.
Go up one level (menu or folder).
Automatic search for a higher radio
frequency.
Select the next CD, USB track.
Scroll in a list.
Press and hold: fast for ward.
Access to the main menu.
.
Bluetooth® audio system