2018 MITSUBISHI OUTLANDER Owner's Manual (in English)

Replacement of light bulbs9-32 Vehicle care and maintenance
9
N00943000132
The bulb should only be replaced with a newbulb with the same rating and type. The typeand rating are listed on the base of the bulb.
N00950302072
NOTE
If you are unsure of how to carry out thework as required, it is recommended thatthese procedures be ca
rried out by an autho-
rized Mitsubishi Motors
dealer or a repair
facility of your choice.Be careful not to scratch the vehicle bodywhen removing a light and lens.When it rains, or wh
en the vehicle has been
washed, the inside of the lens sometimesbecomes temporarily foggy. This is the samephenomenon as when window glass mists upon a humid day, and does not indicate a func-tional problem.When the light is switched on, the heat willremove the fog. However, if water gathersinside the light, please
have it checked by an
authorized Mitsubishi Motors dealer or arepair facility of your choice.
Bulb capacity
Outside Type A: Halogen headlights typeType B: LED headlights typeFrontTy p e ATy p e B
Item
Wa t t-age
ANSI Tr a d e No. or Bulb type
1 - Front turn signal light 21 W PY21W2 - Headlight, high beam 60 W
9005 HB3
3 -
Head-light, low beam
Halogen bulb
55 W H7
LED — —
Daytime running light
——
5 - Front side-marker
light
5 W W5W
6-
Front fog light (if so equipped)
Halogen bulb
19 W H16
LED — —
(if so equipped)
The following lights use an LED instead ofthe bulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when either light need
s to be repaired or
replaced.
BK0249100US.book 32 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-33
9
N00950401731
• Headlight, low be
am (LED type)
• Parking light• Daytime running light• Front fog light (LED type)• Side turn signal light
Item
Wattage
ANSI trade No. or Bulb type
1 - High-mounted
stop light
——
2 - Tail light — —
marker light
——
4 - License plate
light
5 W W5W
5 - Back-up light 16 W W16W
NOTE
Rear
6 - Rear turn sig-
nal light
21 W WY21W
7 - Stop light — —The following lights use an LED instead ofthe bulb. Check with an authorized Mitsubi-shi Motors dealer or a
repair facility of your
choice when either light
needs to be repaired
or replaced.• Rear side-marker light• High-mounted stop light• Tail light• Stop light
Item
Wattage
ANSI trade No. or Bulb type
Inside
Item
Wattage
1 - Cargo room light 8 W2 - Dome light (rear) 8 W3 -
Dome light (front)/Read-ing light
8 W
4 - Downlight –6 - Glove compartment light 1.4 W
NOTE
The following lights us
e an LED instead of
the bulb. Check with an authorized Mitsubi-shi Motors dealer or a repair facility of yourchoice when the light needs to be repaired orreplaced.• Downlight
BK0249100US.book 33 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs9-34 Vehicle care and maintenance
9
N00901801216
1. When replacing the bulb on the left sideof the vehicle, remove the bolts (A) hold-ing down the relay box and the sub fuseblock, and then move them toward therear of the vehicle. (if so equipped)
2. Turn the cap (B) counterclockwise toremove it.3. Turn the socket (C) counterclockwise toremove it, and then pull the bulb out ofthe socket.
4. To install the bulb, perform the removalsteps in reverse.
N00900301171
• Front foot lights• Floor console box light
Headlights (low beam, halogen bulb type) *- Front of the vehicle
NOTE
*- Front of the vehicle
NOTE
When installing the bulb, align the tab (D)with the notch (E) of the socket.
Headlights (low beam, LED type)
NOTE
The headlights use an LED instead of thebulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
BK0249100US.book 34 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-35
9
N00901901132
1. When replacing the bulb on the right sideof the vehicle, rem
ove the clip (A) hold-
ing down the washer tank spout and movethe spout toward the rear of the vehicle.2. Turn the cap (B) counterclockwise toremove it.
3. Turn the bulb (C) counterclockwise toremove it and then while holding downthe tab (D), pull out the bulb (E).4. To install the bulb, perform the removalsteps in reverse.
N00943201359
The alignment of th
e headlights should be
checked by an authorized Mitsubishi Motorsdealer or a repair facility of your choice.
N00915501214
1. When replacing the bulb on the left sideof the vehicle, move the relay box towardthe rear of the vehi
cle. (if so equipped)
(Refer to “Headlight
(low beam, halogen
bulb type): Step 1” on page 9-34.
2. Turn the socket (A
) counterclockwise to
remove it, and then pull the bulb out ofthe socket.3. To install the bulb, perform the removalsteps in reverse.
Headlights (high beam) *- Front of the vehicle
Headlight aim adjustment Front side-marker lights
*- Front of the vehicle
BK0249100US.book 35 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs9-36 Vehicle care and maintenance
9
N00917301724N00943401423
1. Remove the 12 clips (A, B), and thenremove the cover (C).
2. Turn the socket (D
) counterclockwise to
remove it, then remove the bulb from thesocket by turning it counterclockwisewhile pressing in.3. To install the bulb, perform the removalsteps in reverse.
N00943501189N00943601920
1. Insert a straight
blade (or minus) screw-
driver with a cloth over its tip at the pointsindicated by arrows and pry gently toremove the cover (A).
Parking lights/Daytime running lights
NOTE
The parking lights and daytime runninglights use an LED in
stead of the bulb.
Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Front turn signal lights
*: Front of the vehicle
Side turn signal lights
(if so
equipped)
NOTE
The side turn signal lights use an LEDinstead of the bulb. Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Front fog lights (Halogen bulb type)
BK0249100US.book 36 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs
Vehicle care and maintenance 9-37
9
2. Remove the 3 screws
(B) and remove the
light unit.
3. While holding down the tab (D), pull outthe socket (E).4. Turn the bulb (F) counterclockwise toremove it.5. To install the bulb, perform the removalsteps in reverse.
N00943601933N00943701598
1. Open the liftgate.2. Remove the screws (A), and then movethe light unit toward the rear of the vehi-cle to unfix the notch (B) and pins (C).
NOTE
When unfastening the screws or the foglight, be careful not to move the beam posi-tion adjustment screw (C).
Front fog lights (LED type)
NOTE
The fog lights use an
LED instead of the
bulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
Rear combination lights
BK0249100US.book 37 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Replacement of light bulbs9-38 Vehicle care and maintenance
9
3. Turn the socket counterclockwise andremove it, and then pull the bulb out ofthe socket.4. To install the bulb, perform the removalsteps in reverse.
N00929101080
1. Push the light unit upward to remove it.
2. Turn the socket (A) counterclockwise toremove it, and then pull the bulb out ofthe socket.3. To install the bulb, perform the removalsteps in reverse.
D- Rear turn signal lightE- Tail light and stop light (LED) - cannot
be replacedNOTE
The rear side-marker li
ght, tail light and stop
light use an LED instead of the bulb.Check with an authorized Mitsubishi Motorsdealer or a repair fa
cility of your choice
when the light needs to be repaired orreplaced.
NOTE
When mounting the light unit, align thenotch (F) and pin (G) on the light unit withthe clip (H) and hole (I) in the body.
Back-up lights
NOTE
Wrap a cloth around the tip of the screw-driver to keep from scratching the lens.
NOTE
When installing the light unit, first insert thenotch (B) into the hole on the body, and thenpush on the light unit to fit it into place.
BK0249100US.book 38 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Vehicle care precautions
Vehicle care and maintenance 9-39
9
N00944001442
1. When removing the light unit (A), push ittoward the left side of the vehicle body.2. Use a screw driver to gently pry up the tab(B) and remove the lens.
3. Pull the bulb out of the socket.4. To install the bulb, perform the removalsteps in reverse.
N00943900102N00945100166
In order to maintain the value of your vehicle,perform regular mainte
nance using the proper
materials and procedures
. Be sure to use only
those materials and proc
edures that meet your
local environmental pollution control regula-tions. Choose the materials you will use care-fully, to be sure that they do not containcorrosives. If you are
not sure, contact an
authorized Mitsubishi Motors dealer for helpin choosing these materials.
License plate lights
NOTE
Wrap a cloth around the tip of the screw-driver to keep from scratching the lens.
NOTE
When mounting the light unit, insert tab (C)first then align tab (D) with its hole.
High-mounted stop light
NOTE
The high-mounted stop light uses an LEDinstead of the bulb. Check with an authorizedMitsubishi Motors dealer or a repair facilityof your choice when the light needs to berepaired or replaced.
Vehicle care precautions
BK0249100US.book 39 ページ ２０１７年５月１０日　水曜日　午前８時４９分