2018 Lexus LC500 lexus LC500 2018 Navigation Manual

121
4
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
Audio/visual system
■Certification
• CAUTION:
THIS PRODUCT IS A CLASS I LASER PRODUCT. USE OF CONTROLS OR
ADJUSTMENTS OR PERFOR- MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADI- ATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR BY
YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
“PWR·VOL” knob: Press to turn the
audio/visual system on and off. The sys-
tem turns on in the last mode used.
Turn this knob to adjust the volume.
 A function that enables automatic
return to the previous screen from
the audio/visual screen can be
selected. ( P.56)
Using the audio control switch
1 Display the audio control screen.
2 Each time the “RADIO” or
“MEDIA” button is pressed, the
audio source changes.
“RADIO” button: To change radio
modes.
“MEDIA” button: To change media
modes.
From the audio source selection
screen
1 Display the audio control screen.
2 Select “Source” on the sub menu.
3 Select the desired source.
●Dimmed screen buttons cannot be oper- ated.
Some basics
This section describes some of the
basic features of the audio/visual
system. Some information may not
pertain to your system.
Your audio/visual system works
when the engine switch switch> is in ACCESSORY or
IGNITION ON mode .
NOTICE
●To prevent the 12-volt battery from
being discharged, do not leave the audio/visual system on longer than necessary when the engine is not run-
ning .
Turning the system on and off
Selecting an audio source

122
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
1Display the audio control screen.
2 Select “Source” on the sub menu.
3 Select “Reorder”.
4 Select the desired audio source
then or to reorder.
■Inserting a disc
 After insertion, the disc is automati-
cally loaded.
■Ejecting a disc
1 Press the button and remove
the disc.
●The player is intended for use with 4.7 in. (12 cm) discs only.
●When inserting a disc , gently insert the disc with the label facing up.
There are 2 USB ports and an AUX
port in the console box.
1 Slide the armrest as far back while
pressing the button.
2 Lift the armrest while pulling the
knob.
Reordering the audio source
Disc slot
NOTICE
●Never try to disassemble or oil any part of the DVD player. Do not insert anything other than a disc into the slot.
USB/AUX port

123
4
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
Audio/visual system
3Open the cover and connect a
device.
 Turn on the power of the device if it
is not turned on.
●Up to two portable players can be con-
nected to the USB port at the same time.
●Even if a USB hub is used to connect
more than two USB devices, only the first two connected devices will be recog-nized.
1 Display the audio control screen.
2 Select “Sound” on the sub menu.
3 Select the desired switch to be set.
Select to set the treble/mid/bass.
( P.123)
Select to set the fader/balance.
( P.124)
The system adjusts to the optimum
volume and tone quality according
to vehicle speed to compensate for
increased vehicle noise. ( P.124)
This function can create a feeling of
presence. ( P.124)
■Treble/Mid/Bass
How good an audio program sounds is
largely determined by the mix of the
treble, mid and bass levels. In fact, dif-
ferent kinds of music and vocal pro-
grams usually sound better with
different mixes of treble, mid and bass.
1 Select the “Treble/Mid/Bass” and
select the desired item to be set.
Select “+” or “-” to adjust high-
NOTICE
●Depending on the size and shape of the device that is connected to the sys-tem, the console box/auxiliary box may
not close fully. In this case, do not forci- bly close the console box/auxiliary box as this may damage the device or the
terminal, etc.
Sound settings
A
B
C
D
A

124
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
pitched tones.
Select “+” or “-” to adjust mid-
pitched tones.
Select “+” or “-” to adjust low-
pitched tones.
■Fader/Balance
A good balance of the left and right
stereo channels and of the front and
rear sound levels is also important.
Keep in mind that when listening to a
stereo recording or broadcast, chang-
ing the right/left balance will increase
the volume of 1 group of sounds while
decreasing the volume of another.
1 Select the “Fader/Balance” and
select the desired item to be set.
Select to adjust the sound balance
between the front and rear speak-
ers.
Select to adjust the sound balance
between the left and right speakers.
■Automatic sound levelizer
The system adjusts to the optimum vol-
ume and tone quality according to
vehicle speed to compensate for
increased vehicle noise.
1 Select to set the Automatic sound
levelizer on/off.
■Surround
This function can create a feeling of
presence.
1 Select to set the surround on/off.
■Screen size settings
The screen size can be selected for
each type of media.
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Audio” on the sub menu.
4 Select “Common”.
5 Select “Screen format”.
DVD video/USB video
Miracast™
Select to display a 4 : 3 screen, with
either side in black.
B
C
A
B
Audio screen adjustment
A

125
4
-$@-$I@/BWJ@0.&@ &&

4-1. Basic operation
Audio/visual system
Select to enlarge the image hori-
zontally and vertically to full screen.
Select to enlarge the image by the
same ratio horizontally and verti-
cally.
■Contrast, Brightness, Color and
Tone adjustment
The brightness, contrast, color and
tone of the screen can be adjusted.
DVD video/USB video/Miracast™
1 Press the “MENU” button on the
Remote Touch.
2 Select “Setup”.
3 Select “Audio”.
4 Select “Common”.
5 Select “Display”.
 “Colour”
“R”: Select to strengthen the red color of
the screen.
“G”: Select to strengthen the green color
of the screen.
 “Tone”
“+”: Select to strengthen the tone of the
screen.
“-”: Select to weaken the tone of the
screen.
 “Contrast”
“+”: Select to strengthen the contrast of the
screen.
“-”: Select to weaken the contrast of the
screen.
 “Brightness”
“+”: Select to brighten the screen.
“-”: Select to darken the screen.
●Depending on the audio source, some functions may not be available.
1 Press this switch to operate the
speech command system.
 The speech command system and
its list of commands can be oper-
ated. ( P.168)
B
C
Speech command system

126
-$@-$I@/BWJ@0.&@ &&

4-2. Radio operation
4-2.Radio operation
The radio control screen can be
reached by the following methods:
Using the audio control switch
1 Press the “RADIO” button.
Using the Remote Touch
1 Press the “MENU” button on the
Remote Touch, then select “Radio”.
Select to tune to preset sta-
tions/ensembles. ( P.126)
Favorites: Turn to move up/down
the preset stations.
Station list: Turn to move up/down
the station list.
Manual: Seek up/down (Hold to
non stop seek up/down)
Favorites: Turn to move up/down
the preset stations.
Station list: Turn to move up/down
the station list.
Manual: (AM/FM) Tune up/down
(DAB) Seek up/down.
DAB time shift screen: Turn to jump
forward/ backwards.
●The radio automatically changes to ste- reo reception when a stereo broadcast is
received.
●If the signal becomes weak, the radio
reduces the amount of channel separa- tion to prevent the weak signal from cre-ating noise. If the signal becomes
extremely weak, the radio switches from stereo to mono reception.
Up to 6 preset stations can be regis-
tered.
1 Tune in the desired station.
2 Select one of the screen buttons (1-
6) and hold it until a beep is heard.
 The station’s frequency will be dis-
played in the screen button.
 To change the preset station to a dif-
AM/FM/DAB radio
Overview
Control screen
Audio control switch
A
A
Presetting a station
B

127
4
-$@-$I@/BWJ@0.&@ &&

4-2. Radio operation
Audio/visual system
ferent one, follow the same proce-
dure.
Depending on the availability of RDS
infrastructure, the service may not
function properly.
■AF (Alternative frequency) func-
tion
A station providing good reception is
automatically selected if current
reception worsens.
■TA (Traffic announcement) func-
tion
The tuner will automatically seek a sta-
tion that regularly broadcasts traffic
information and the station broadcasts
when the traffic information program
starts.
1 A pop-up message is displayed on
the screen when the radio seeks
out a TP station.
2 Select “Continue”.
●When “FM traffic announcement” is set to “On” ( P.149), the radio will begin
seeking a TP station.
●When the program ends , the initial oper-
ation resumes.
■Traffic announcement volume
function
The volume level when receiving the
traffic announcement is memorized.
AM
Select to display the audio source
selection screen. ( P.121)
Select to display the preset station
screen.
Select to display the manual tuning
screen. ( P.128)
Select to display the sound setting
screen. ( P.123)
FM
Select to display the audio source
selection screen. ( P.121)
Select to display the preset station
screen. ( P.126)
Select to display the station list.
Select to display the manual tuning
screen. ( P.128)
RDS (Radio data system)
Sub menu
A
B
C
D
A
B
C
D

128
-$@-$I@/BWJ@0.&@ &&

4-2. Radio operation
Select to display the radio options
screen. ( P.128)
Select to display the sound setting
screen. ( P.123)
DAB
Select to display the audio source
selection screen. ( P.121)
Select to display the preset station
screen. ( P.126)
Select to display the station list.
Select to display the manual tuning
screen. ( P.128)
Select to display the time shift con-
trol screen. ( P.129)
Select to display the radio options
screen. ( P.128)
Select to display the sound setting
screen. ( P.123)
AM/FM
1 Select “Manual” on the sub menu.
2 Tune the desired station.
Select to seek up/down for a sta-
tion.
Select to step up/down frequen-
cies.
DAB
1 Select “Manual” on the sub menu.
2 Tune the desired ensemble or ser-
vice.
Select to set the desired ensemble.
Select to set the desired service.
1 Select “Options” on the sub menu.
2 Select the desired item to be set.
E
F
A
B
C
D
E
F
G
Manual tuning
Radio option
A
B
A
B