2018 KIA STONIC lock

4. If the glow indicator light goes out,turn the ignition switch to the
START position and hold it there
until the engine starts (a maximum
of 10 seconds), then release the
key.
NOTICE
If the engine is not started within 10
seconds after the preheating is com‐
pleted, turn the ignition switch once
more to the LOCK position during 10
seconds, and then to the ON posi‐
tion, in order to preheat again.
Starting and stopping the engine
for turbocharger intercooler
1. Do not race or accelerate the en‐ gine immediately after starting.
If the engine is cold, idle for several
seconds before sufficient lubrica‐
tion is ensured in the turbocharger
unit. 2. After high speed or extended driv‐
ing, requiring a heavy engine load,
idle the engine about 1 minute be‐
fore turning it off.
This idle time will allow the turbo‐ charger to cool prior to shutting off
the engine.
CAUTION
Do not turn off the engine immedi‐ately after it has been subjected to aheavy load. Doing so may cause se‐vere damage to the engine or turbo‐charger unit.

6-09
6
Driving your vehicle

ENGINE START/STOP BUTTON (IF EQUIPPED)
Illuminated ENGINE START/STOP
button
Whenever the front door is opened, the
ENGINE START/STOP button will illumi‐ nate for your convenience. The light will
go off after about 30 seconds when the
door is closed. It will also go off imme‐
diately when the theft-alarm system is
armed.
ENGINE START/STOP button
position
OFF
With manual transaxle
To turn off the engine (START/RUN position) or ve‐
hicle power (ON position), stop the vehicle then press the ENGINE START/STOP button.
With automatic transaxle
To turn off the engine (START/RUN po‐
sition) or vehicle power (ON position),
press the ENGINE START/STOP button with the shift lever in the P (Park) posi‐
tion. When you press the ENGINE
START/STOP button without the shift lever in the P (Park) position, the EN‐
GINE START/STOP button will not
change to the OFF position but to the ACC position.
Also, the steering wheel locks when the
ENGINE START/STOP button is in the
OFF position to protect you against theft. It locks when the door is opened.
Not illuminated
Vehicles equipped with anti-theftsteering column lock
The steering wheel locks when the en‐ gine start/stop button is in the OFF po‐
sition to protect you against theft. It
locks when the door is opened.
If the steering wheel is not locked prop‐ erly when you open the driver's door,
the warning chime will sound. If the
problem is not solved, have the system checked by a professional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
In addition, if the ENGINE START/STOP button is in the OFF position after the
driver's door is opened, the steering
wheel will not lock and the warning chime will sound. In such a situation,
close the door. Then the steering wheel
will lock and the warning chime will stop.
NOTICE
If the steering wheel doesn't unlock
properly, the ENGINE START/STOP
button will not work. Press the EN‐
(Continued)
Driving your vehicle
6-10

(Continued)
GINE START/STOP button while
turning the steering wheel right and
left to release the tension.
•If difficulty is experienced turning
the engine start/stop button to
the ACC position, turn the steering
wheel right and left to release the
tension while pressing the engine
start/stop button.
•When you turn off the engine, the
vehicle should be stopped.
CAUTION
You are able to turn off the engine(START/RUN) or vehicle power (ON),only when the vehicle is not in mo‐tion. In an emergency situation whilethe vehicle is in motion, you are ableto turn the engine off and to theACC position by pressing the enginestart/stop button for more than 2seconds or 3 times successivelywithin 3 seconds. If the vehicle is stillmoving, you can restart the engine
(Continued)
(Continued)
without depressing the brake pedalby pressing the engine start/stopbutton with the shift lever in the N(Neutral) position.
ACC (Accessory)
With manual transaxle
Press the engine start/stop button when the button is
in the OFF position without depressing the clutch pedal.
With automatic transaxle
Press the ENGINE START/STOP button
while it is in the OFF position without depressing the brake pedal.
The steering wheel unlocks and electri‐
cal accessories are operational.
If the ENGINE START/STOP button is in
the ACC position for more than 1 hour, the button is turned off automatically
to prevent battery discharge.
0SBOHF
ON
With manual transaxle
Press the engine start/stop button when the button is
in the ACC position without depressing the clutch pedal.
3FE
With automatic transaxle
Press the ENGINE START/STOP button
while it is in the ACC position without depressing the brake pedal.
The warning lights can be checked be‐
fore the engine is started. Do not leave
the ENGINE START/STOP button in the ON position for a long time. The bat‐
tery may discharge, because the engineis not running.
START/RUN
With manual transaxle
To start the engine, depress the clutch pedal and brake
pedal, then press the engine start/stop button with theshift lever in the N (Neutral) position.
With automatic transaxle
To start the engine, depress the brake
pedal and press the engine start/stop
button with the shift lever in the P (Park) or the N (Neutral) position. For
your safety, start the engine with the
shift lever in the P (Park) position.
/PU
JMMVNJOBUFE

6-11
6
Driving your vehicle

NOTICE
If you press the ENGINE START/
STOP button without depressing the
clutch pedal for manual transaxle
vehicles or without depressing the
brake pedal for automatic transaxle
vehicles, the engine will not start
and the engine start/stop button
changes as follow:
OFF ➔ACC ➔ ON ➔ OFF or ACC
NOTICE
If you leave the ENGINE START/STOP
button in the ACC or ON position for
a long time, the battery will dis‐
charge.
WARNING
•Never press the ENGINE START/STOP button while the vehicle is inmotion. This would result in loss ofdirectional control and brakingfunction, which could cause an ac‐cident.
•The anti-theft steering columnlock is not a substitute for theparking brake. Before leaving thedriver's seat, always make surethe shift lever is engaged in P(Park), set the parking brake fullyand shut the engine off. Unexpec‐ted and sudden vehicle movementmay occur if these precautions arenot taken.
•Never reach for the ENGINESTART/STOP button or any othercontrols through the steeringwheel while the vehicle is in mo‐tion. The presence of your hand orarm in the area could cause loss ofvehicle control, an accident and se‐rious bodily injury or death.
(Continued)
(Continued)
•Do not place any movable objectsaround the driver's seat as theymay move while driving, interferewith the driver and lead to an acci‐dent.
Starting the engine
WARNING
•Always wear appropriate shoeswhen operating your vehicle. Un‐suitable shoes (high heels, skiboots, etc.) may interfere withyour ability to use the brake andaccelerator pedal.
•Do not start the vehicle with theaccelerator pedal depressed. Thevehicle can move and lead to anaccident.
•Wait until the engine rpm is nor‐mal. The vehicle may suddenlymove if the brake pedal is releasedwhen the rpm is high.
Driving your vehicle
6-12

• If you press the ISG OFF button again,the system will be activated and the
light on the ISG OFF button will turn off.
ISG system malfunction
The system may not operate
when:
- The ISG related sensors or system
error occurs.
The yellow AUTO STOP indicator (
)
on the instrument cluster will stay on
after blinking for 5 seconds and the light on the ISG OFF button will illumi‐
nate.
NOTICE
•If the ISG OFF button light is not
turned off by pressing the ISG OFF
button again or if the ISG system
continuously does not work cor‐
rectly, have your vehicle inspected
by a professional workshop as
soon as possible.
Kia recommends to contact an au‐
thorized Kia dealer/service part‐
ner.
•When the ISG OFF button light
comes on, it may stop illuminating
after driving your vehicle at ap‐
proximately 80 km/h for a maxi‐
mum of two hours and setting the
fan speed control knob below the
2nd position. If the ISG OFF button
light continues to be illuminated in
spite of the procedure, have your
vehicle inspected by a professional
workshop as soon as possible. Kia
recommends to contact an au‐
thorized Kia dealer/service part‐
ner.
NOTICE
If you want to use the ISG function,
the battery sensor needs to be cali‐
brated for approximately 4 hours
with the ignition off and then, turn
the engine on and off 2 or 3 times.
WARNING
When the engine is in Idle Stopmode, it's possible to restart the en‐gine without the driver taking anyaction.Before leaving the car or doing any‐thing in the engine room area, stopthe engine by turning the ignitionswitch to the LOCK(OFF) position orremoving the ignition key.

6-19
6
Driving your vehicle

This shift pattern is imprinted on the
shift knob. The transaxle is fully synchronized in all forward gears so
shifting to either a higher or a lower
gear is easily accomplished.
Depress the clutch pedal down fully while shifting, then release it slowly.
If your vehicle is equipped with an igni‐
tion lock switch, the engine will not
start when starting the engine without depressing the clutch pedal. (if equip‐
ped)
The shift lever must be returned to the
neutral position before shifting into R (Reverse).
Push the button located immediately
below the shift knob and pull the gear‐
shift lever to the left sufficiently, and then shift into reverse (R) gear position.
Make sure the vehicle is completely
stopped before shifting into R (Re‐verse).
Never operate the engine with thetachometer (rpm) in the red zone.
CAUTION
•When downshifting from fifth gearto fourth gear, caution should betaken not to inadvertently pressthe shift lever sideways in such amanner that the second gear isengaged. Such a drastic downshiftmay cause the engine speed to in‐crease to the point that the tach‐ometer will enter the red-zone.Such over-revving of the engineand transaxle may possibly causeengine damage.
•Do not downshift more than 2gears or downshift the gear whenthe engine is running at high speed(5,000 RPM or higher). Such adownshifting may damage the en‐gine, clutch and the transaxle.
• During cold weather, shifting may be difficult until the transaxle lubricant
is warmed up. This is normal and not harmful to the transaxle. • If you've come to a complete stop
and it's hard to shift into 1st or R(Re‐
verse), leave the shift lever at N(Neu‐
tral) position and release the clutch.
Press the clutch pedal back down, and then shift into 1st or R(Reverse)
gear position.
CAUTION
•To avoid premature clutch wearand damage, do not drive withyour foot resting on the clutchpedal. Also, don’t use the clutch tohold the vehicle stopped on an up‐hill grade, while waiting for a traf‐fic light, etc.
•Do not use the shift lever as ahandrest during driving, as this canresult in premature wear of thetransaxle shift forks.
•To prevent possible damage to theclutch system, do not start withthe 2nd (second) gear engaged ex‐cept when you start on a slipperyroad.

6-21
6
Driving your vehicle

(Continued)
•Always check the surroundingareas near your vehicle for people,especially children, before shiftinga car into D (Drive) or R (Reverse).
•Before leaving the driver’s seat, al‐ways make sure the shift lever isin the P (Park) position; then setthe parking brake fully and shutthe engine off. Unexpected andsudden vehicle movement can oc‐cur if these precautions are notfollowed in the order identified.
•Do not use the engine brake (shift‐ing from a high gear to lower gear)rapidly on slippery roads.The vehicle may slip causing an ac‐cident.
CAUTION
•To avoid damage to your trans‐axle, do not accelerate the enginein R (Reverse) or any forward gearposition with the brakes on.
(Continued)
(Continued)
•When stopped on an incline, do nothold the vehicle stationary withengine power.Use the service brake or the park‐ing brake.
•Do not shift from N (Neutral) or P(Park) into D (Drive), or R (Reverse)when the engine is above idlespeed.
Transaxle ranges
The indicator in the instrument cluster
displays the shift lever position when the ignition switch is in the ON position.
P (Park)
Always come to a complete stop before
shifting into P (Park). This position
locks the transaxle and prevents the drive wheels from rotating.
WARNING
•Shifting into P (Park) while the ve‐hicle is in motion will cause thedrive wheels to lock which willcause you to lose control of thevehicle.
•Do not use the P (Park) position inplace of the parking brake. Alwaysmake sure the shift lever is latch‐ed in the P (Park) position and setthe parking brake fully.
•Never leave a child unattended in avehicle.
CAUTION
The transaxle may be damaged ifyou shift into P (Park) while the ve‐hicle is in motion.
R (Reverse)
Use this position to drive the vehicle
backward.

6-25
6
Driving your vehicle

Sports mode (if equipped)

61

%08/

4QPSUT

NPEF
Whether the vehicle is stationary or in
motion, sports mode is selected by pushing the shift lever from the D
(Drive) position into the manual gate.
To return to D (Drive) range operation, push the shift lever back into the main
gate.
In sports mode, moving the shift lever
backwards and forwards will allow you to make gearshifts rapidly. In contrast
to a manual transaxle, the sports mode
allows gearshifts with the accelerator
pedal depressed.
Using the shift lever
Up (+) : Push the lever forward once to shift up one
gear.
Down (-) : Pull the lever backwards once to shift down one
gear.
NOTICE
•In sports mode, the driver must
execute upshifts in accordance
with road conditions, taking care
to keep the engine speed below
the red zone.
•In sports mode, only the 4 or 6
forward gears can be selected. To
reverse or park the vehicle, move
the shift lever to the R (Reverse)
or P (Park) position as required.
•In sports mode, downshifts are
made automatically when the ve‐
hicle slows down. When the vehicle
stops, 1st gear is automatically
selected.
(Continued)
(Continued)
•In sports mode, when the engine
rpm approaches the red zone shift
points are varied to upshift auto‐
matically.
•To maintain the required levels of
vehicle performance and safety,
the system may not execute cer‐
tain gearshifts when the shift lev‐
er is operated.
•When driving on a slippery road,
push the shift lever forward into
the +(up) position. This causes the
transmission to shift into the 2nd
gear which is better for smooth
driving on a slippery road. Push
the shift lever to the -(down) side
to shift back to the 1st gear.
Shift lock system (if equipped)
For your safety, the automatic trans‐
axle has a shift lock system which pre‐ vents shifting the transaxle from P
(Park) into R (Reverse) unless the brake
pedal is depressed.
To shift the transaxle from P (Park) in‐ to R (Reverse): 1. Depress and hold the brake pedal.

6-27
6
Driving your vehicle