2018 JEEP RENEGADE air condition

the device keeps working if the radar
sensor is obstructed.
Before returning to the previously set
speed, bring the speed close to that
value, then press the RES button and
release it.
WARNING
134)Pay the utmost attention while
driving at all times and be always ready to
press the brakes if needed.
135)The system is an aid for the driver,
who must always pay full attention while
driving. The responsibility always rests
with the driver, who must take into
account the traffic conditions in order to
drive in complete safety. The driver must
always maintain a safe distance from the
vehicle in front.
136)The device is not activated in
presence of pedestrians, oncoming
vehicles in the opposite direction of travel
or moving in the crosswise direction and
stationary objects (e.g. a vehicle standing
in a queue or a broken down vehicle).
137)The device cannot take account of
road, traffic and weather conditions, and
conditions of poor visibility (e.g. fog).138)The device does not always fully
recognise complex driving conditions that
could cause it to determine the safe
distance to be held incorrectly or not at
all.
139)The device cannot apply the
maximum braking force: the car will not
be stopped completely.IMPORTANT
54)The system may have limited or absent
operation due to weather conditions such
as: heavy rain, hail, thick fog, heavy snow.
55)The section of the bumper before the
sensor must not be covered with
adhesives, auxiliary headlights or any other
object.
56)Operation can be adversely affected by
any structural change made to the vehicle,
such as a modification to the front
geometry, tyre change, or a heavier load
than the standard load of the vehicle.
57)Incorrect repairs made on the front
part of the vehicle (e.g. bumper, chassis)
may alter the position of the radar sensor,
and adversely affect its operation. Go to a
Jeep Dealership for any operation of this
type.58)Do not tamper with nor carry out any
intervention on the radar sensor or on the
camera on the windscreen. In the event of
a sensor failure, contact a Jeep
Dealership.
59)Do not wash with high-pressure jets in
the bumper lower area: in particular do not
operate on the system's electrical
connector.
60)Be careful in the case of repairs and
new paintings in the area around the
sensor (panel covering the sensor on the
left side of the bumper). In the event of a
frontal impact the sensor may
automatically deactivate and display a
warning to indicate that the sensor needs
to be repaired. Even without a malfunction
warning, deactivate the system operation if
you think that the position of the radar
sensor has changed (e.g. due to low-speed
frontal impact as during parking
manoeuvres). In these cases, go to a Jeep
Dealership to have the radar sensor
realigned or replaced.
167

uneven road surface or obstacles
before the wheels, affect vehicle's
movements, thus preventing it from
following the correct path.
IMPORTANT Manoeuvring is
deactivated if, after about 3 minutes,
parking has not been completed.
End of manoeuvre
The semi-automatic manoeuvre ends
when the display shows the message of
completed manoeuvre.
At the end of the manoeuvre, the driver
resumes control of the car and, if
necessary, has to complete parking
manually.
IMPORTANT INFORMATIONIf the sensors undergo impact which
alters their position, the system operation
could deteriorate considerably.
The system reaches top performance
after the vehicle has covered about
50 km (system "self-calibration").
If the sensors are dirty, covered by
snow, ice or mud or are repainted vs. the
original conditions, the system operation
could result strongly degraded. It is
extremely important that the sensors are
always clean in order for the system to
operate correctly. During cleaning make
sure not to scratch or damage them;
avoid using dry or rough cloths. Thesensors should be washed using clean
water with the addition of car shampoo if
necessary. In washing stations, clean the
sensors quickly, keeping the steam
jet/high pressure washing nozzles at least
10 cm away from the sensors.
Ultrasonic sound sources (e.g.
pneumatic brakes of trucks or air drills)
nearby could negatively influence the
sensor performance.
Sensors may detect a non-existent
obstacle (echo noise) due to mechanical
noises, for example while washing the
vehicle, in the case of rain, strong wind,
hail.
The sensors may not detect objects of
a particular shape or made from
particular materials (very thin poles,
trailer beams, panels, nets, bushes,
anti-parking posts, pavements, rubbish
bins, motor vehicles, etc.). Always take
great care to check that the vehicle and
its path are actually compatible with the
parking place identified by the system.
The use of (one or more) tyres or
wheels of a different size to those at the
time of vehicle purchase could affect the
operation of the system.
If a trailer (with correctly engaged
socket) is present, the system will be
automatically disabled.
In "Search in progress" mode, the
system could incorrectly identify a
parking place to carry out the manoeuvre(e.g. by a junction, driveways, roads
crossing the direction of travel, etc.).
In the case of parking manoeuvres on
roads on a gradient, the performance of
the system could be inferior and it may
deactivate.
If a parking manoeuvre is being
carried out between two parked vehicles
alongside the pavement, the system may
cause the vehicle to mount the
pavement.
Some manoeuvres at very tight bends
might be impossible to be carried out.
Take great care to ensure that
conditions do not change during the
parking manoeuvre (e.g. if there are
persons and/or animals in the parking
place, moving vehicles, etc.) and
intervene immediately if necessary.
During parking manoeuvres, pay
attention to cars approaching from the
opposite direction. Always comply with
the prescriptions of the Highway Code.
IMPORTANT Correct system operation
is not guaranteed if snow chains or the
space-saver wheel are fitted.
IMPORTANT The function only informs
the driver about the last appropriate
parking place (parallel or
perpendicular) detected by the parking
sensors.
174
STARTING AND DRIVING

WARNING
154)If the replaced fuse blows again,
contact a Jeep Dealership.
155)Never replace a fuse with another
with a higher amp rating; DANGER OF
FIRE.
156)If a general fuse (MAXI-FUSE,
MEGA-FUSE, MIDI-FUSE) cuts in, do not
attempt any repair and contact a Jeep
Dealership.
157)Before replacing a fuse, make sure
that the ignition device is at STOP, that
the key, if mechanical, has been removed
and that all devices are switched off
and/or disconnected.
158)If a general protection fuse for safety
systems (airbag system, braking system),
power unit systems (engine system,
transmission system) or steering system
blows, contact a Jeep Dealership.
IMPORTANT
77)Never replace a fuse with metal wires
or anything else.
78)If it is necessary to wash the engine
compartment, take care not to directly hit
the fuse box and the window wiper motors
with the water jet.
CHANGING A WHEEL
159) 160) 161) 162) 163) 166) 167)
JACK
164) 165)
Please note that:the weight of the jack is 2.8 kg;the jack requires no adjustment;the jack cannot be repaired and in the
event of a fault it must be replaced by
another genuine one;
no tool other than its cranking device
may be fitted on the jack.
Maintenance
prevent any dirt from depositing on
the "worm screw";
keep the "worm screw" lubricated;never modify the jack.
Conditions for non-use
temperatures below −40°C;on sandy or muddy ground;on uneven ground;on steep roads;in extreme weather conditions:
thunderstorms, typhoons, hurricanes,
blizzards, storms, etc...
in direct contact with the engine or for
repairs under the car;
on boats.
209

handbrake. Take the compressor and
restore pressure using the black inflation
tube L.
If the pressure shown is higher than1.8 bar / 26 psi, restore the pressure and
drive safely to a Jeep Dealership as soon
as possible. If, however, the pressure is
lower than 1.8 bar / 26 psi, do not
resume driving but contact a Jeep
Dealership.
INFLATION PROCEDURE
Proceed as follows:stop the car safely, as described
above, and operate the electric
handbrake;
extract the black inflation tube and
screw it firmly onto the tyre valve. Then
follow the instructions below. Press the
air release button M to adjust any
excessive tyre pressure (see "Repair
procedure" paragraph).
CARTRIDGE REPLACEMENT
Proceed as follows:only use original cartridges, which can
be purchased from the Jeep Dealership;
to remove the cartridge, press the
release button and lift it (see description
above).
WARNING
168)IMPORTANT: Do not exceed
80 km/h. Avoid sudden acceleration or
braking. The kit provides a temporary
repair, therefore the tyre must be
examined and repaired by a specialist as
soon as possible. Before using the kit,
ensure that the tyre is not excessively
damaged and that the rim is in good
condition, otherwise do not use it and call
roadside assistance. Do not remove
foreign bodies from the tyre. Do not let the
compressor turned on for more than
20 consecutive minutes - overheating
hazard.
169)The information required by the
applicable regulation is indicated on the
Fix&Go kit package label. Carefully read
the label on the cartridge before use,
avoid improper use. The kit should be
used by adults and cannot be used by
children.
L
181J0A0959
8 km / 5 mi
182J0A0960
217

SCHEDULED SERVICING
Correct servicing is crucial for
guaranteeing a long life for the car under
the best conditions. For this reason, Jeep
has planned a series of checks and
services at fixed distance intervals and,
where provided, at fixed time intervals,
as described in the Scheduled Servicing
Plan.
Before each coupon however you always
need to pay attention to what is written
in the Scheduled Servicing Plan (e.g.
periodically check liquid levels, tire
pressure, etc.).
The Scheduled Servicing is carried out
by the Jeep Assistance Network at
pre-set times. If, during each operation,
in addition to the ones scheduled, the
need arises for further replacements or
repairs, these may be carried out with the
owner's explicit agreement only. If your
car is used frequently for towing, the
interval between one scheduled servicing
operation and the next should be
reduced.
IMPORTANT Scheduled Servicing
interventions are set out by the
Manufacturer. Failure to have them
carried out may invalidate the
warranty. It is advisable to inform aJeep Dealership of any small operating
irregularities without waiting for the
next service.
PERIODIC CHECKS
Every1,000km or before long trips
check and, if necessary, top up:
engine coolant level;brake fluid level;windscreen washer fluid level;tyre inflation pressure and condition;operation of lighting system
(headlights, direction indicators, hazard
warning lights, etc.);
operation of screen washer/wiper
system and positioning/wear of
windscreen/rear window wiper blades.
Every3,000km, check and top up if
required: engine oil level.
DEMANDING USE OF THE CAR
If the vehicle is used in one of the
following conditions:
Law enforcement (or security service),
taxi service
towing a trailer or caravan;dusty roads;short, repeated journeys (less than
7-8 km) at sub-zero outside
temperatures;
engine often idling or driving long
distances at low speeds or long periods
of inactivity;the following checks must be carried out
more often than indicated in the
Scheduled Service Plan:
check front disc brake pad condition
and wear;
check cleanliness of bonnet and
luggage compartment locks, cleanliness
and lubrication of linkage;
visually inspect conditions of: engine,
gearbox, transmission, pipes and hoses
(exhaust/fuel system/brakes) and rubber
elements (gaiters/sleeves/bushes, etc.);
check battery charge and battery fluid
level (electrolyte);
visually inspect conditions of the
accessory drive belts;
check and, if necessary, change
engine oil and replace oil filter;
check and, if necessary, replace pollen
filter;
check and, if necessary, replace air
cleaner.
228
SERVICING AND MAINTENANCE

SERVICE SCHEDULE (1.4 T-Jet 120 HP LPG / 1.4 Turbo Multi Air / 2.4 Tigershark versions)
IMPORTANT Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the
frequency indicated in the plan by marking each operation with a dot or dedicated note. Warning: simply restarting the maintenance
from the start of the plan may cause the allowed interval to be exceeded for some operations!
Thousands of miles9 182736455463728190
Thousands of kilometres15 30 45 60 75 90 105 120 135 150
Years12345678910
Check the conditions/wear of tires and any pressure
adjustment; check conditions/expiry of the TireKit
recharge (where there is one)
Check operation of lighting system (headlights, direction
indicators, hazard warning lights, boot, passenger
compartment, glove compartment, instrument panel
warning lights, etc.)
Check and, if necessary, top up fluid levels(1)
Visually inspect the condition of: LPG pipes and
connectors, LPG tank fixing (1.4 T-Jet 120 HP LPG
versions)
(1) Always only use the liquids shown in the handbook for topping up after having checked that the system is not damaged.
229

Thousands of miles9 182736455463728190
Thousands of kilometres15 30 45 60 75 90 105 120 135 150
Years12345678910
Visually inspect condition of the accessory drive belt(s)
(2)
Check tension of accessory drive belt (versions without
automatic tensioner)
Visually inspect conditions of toothed timing drive belt
(1.4 Turbo Multi Air and 1.4 T-Jet 120 HP LPG
versions)(2)
Check drive transmission idler unit (PTU) oil level
(4x4 versions)
Check rear differential fluid level (4x4 versions)
Check oil level of electro-hydraulic actuator and top up if
necessary (1.4 Turbo Multi Air versions with dual-clutch
automatic transmission) (3)
(2) The maximum mileage is 120,000 km. Regardless of the mileage, the belt must be replaced every 6 years. If the vehicle is used in
heavy conditions (dusty areas, cold climates, urban driving, long periods of idling), the maximum mileage is 60,000 km. The belt must
be replaced every 4 years regardless of the mileage.
(3) Check to be carried out every year for cars on the road in countries with particularly severe climates (cold countries).
231

Thousands of miles9 182736455463728190
Thousands of kilometres15 30 45 60 75 90 105 120 135 150
Years12345678910
Replace starter spark plug (2.4 Tigershark versions -
where there is one)
Replace accessory drive belt/s(2)
Replace timing belt (1.4 T-Jet 120 HP LPG and
1.4 Turbo Multi Air versions)(2)
Replace air cleaner cartridge (7)
Replace the filter inside the pressure regulator (1.4 T-Jet
120 HP LPG versions)
Replace the paper filter (gaseous LPG) (1.4 T-Jet 120 HP
LPG versions)
(2) The maximum mileage is 120,000 km. Regardless of the mileage, the belt must be replaced every 6 years. If the vehicle is used in
heavy conditions (dusty areas, cold climates, urban driving, long periods of idling), the maximum mileage is 60,000 km. The belt must
be replaced every 4 years regardless of the mileage.
(7) If the vehicle is used in dusty areas, this cleaner must be replaced every 15,000 km.
233