2018 FIAT 500 headlights

KNOWING YOUR CAR
22
SIDE LIGHTS AND DIPPED BEAM HEADLIGHTS - FOLLOW ME HOME
Side lights and dipped beam headlights
The warning light switches on when the side lights or dipped headlights are turned on.
Follow Me Home
The warning light comes on, on some versions along with a dedicated message on the display, when the
“Follow me home” device is used.
33
iTPMS SYSTEM (for versions/markets, where provided)
Low tyre pressure
The warning light switches on constantly to indicate that the pressure of one or more tyres is lower than the recommended
value or to indicate a slow loss of pressure.
In this way the iTPMS warns the driver that one or more tyres may be flat and probably punctured. In this case it is advisable
to restore the correct pressure value.
Once the normal operating conditions of the vehicle are restored, carry out the Tyre reset procedure.
IMPORTANT Do not continue driving with one or more flat tyres as handling may be compromised.
Stop the vehicle, avoiding sharp braking and steering.
iTPMS failure/iTPMS temporarily deactivated
The warning light flashes for about 75 seconds and then stays on constantly (together with a message on the display) to
indicate that the system is temporarily deactivated or faulty.
The system goes back to normal operation when the operating conditions allow it. If this is not the case, carry out the Reset
procedure after restoring the normal operating conditions.
If the malfunction warning persists, contact a Fiat Dealership as soon as possible.
n
FOG LIGHTS
The warning light comes on when the fog lights are turned on.
LEFT-HAND DIRECTION INDICATOR
The warning light turns on when the direction indicator control lever is moved downwards or, together with the right
indicator, when the hazard warning light button is pressed.
55
FR

23
RIGHT-HAND DIRECTION INDICATOR
The warning light switches on when the direction indicator control stalk is moved upwards or, together with the left
indicator, when the hazard warning light button is pressed.
“DUALDRIVE” ELECTRIC POWER STEERING ACTIVATION
The indication CITY switches on when the “Dualdrive” electric power steering system is activated by pressing the “CITY”
button on the dashboard. Press the button again to turn the CITY indication off. CITY
SPORT
ECO
DUALOGIC
GEARBOX
MESSAGES
11
MAIN BEAM HEADLIGHTS
The light comes on when the main beam headlights are turned on.
SPORT FUNCTION ON
The indication SPORT appears on the display when the “SPORT” function is selected by pressing the respective button on
the dashboard. The SPORT indication will switch off when the button is pressed again.
A dedicated screen instead of the “SPORT” indication is displayed on some versions.
ECO FUNCTION ON
The indication ECO appears on the display when the “ECO” function is selected by pressing the respective button on the
dashboard. The ECO indication will switch off when the button is pressed again.
A dedicated page instead of the “ECO” indication is displayed on some versions.
For versions equipped with “Dualogic” gearbox, the following messages can be displayed:
Reduce gear changes – Manual method unavailable – Automatic method unavailable – Clutch overheating – Depress
brake pedal – Depress brake pedal - Engine start delayed – Gear unavailable
Operation not admissible – Depress brake pedal and repeat operation – Shift to neutral.
DE
ENABLING CRUISE CONTROL
The indicator light turns on when cruise control is activated.
ENABLING THE SPEED LIMITER
The indicator light comes on when the speed limiter is activated.

KNOWING YOUR CAR
24
DISPLAY
MULTIFUNCTION
DISPLAY
The standard screen fig. 4 shows the
following information:
1 Odometer (display of distance travelled
in kilometres/miles)
2 Cruise Control/Speed Limiter
3 Indication of possible ice on the road
4 Digital fuel level gauge
5 Date and time
6 Gear engaged indication
(Dualogic versions)
7 Gear Shift Indicator
8 Outside temperature gauge
9 Headlight alignment position
(only with dipped headlights on)
4DVDF0S0225c
10 SPORT driving mode indication / ECO
driving mode indication
11 Dualdrive electric power steering
enabled
12 Digital engine coolant thermometer
13 Speed Limiter set speed
14 Car service indicator
COLOUR DISPLAY
The standard screen fig. 5 shows the
following information:
1 Odometer (display of distance travelled
in kilometres/miles)
2 Digital engine coolant temperature
gauge
3 Digital rev counter (tachometer)
4 Gear Shift Indicator
5 Date
6 Outside temperature gauge
7 Dualdrive electric steering engagement
8 Car speed indication
9 Headlight alignment position (only with
dipped headlights on)
10 Time
11 eco Index
12 Digital fuel level gauge
13 Gear engaged indication
(Dualogic gearbox versions only)SETUP MENU
5DVDF0S172c
6DVDF0S0226c
The setup menu comprises a series of
functions with a circular arrangement.
The setup menu can be activated by
briefly pressing the
MENU button fig. 6.

27
HEADLIGHT
ALIGNMENT
With the ignition key at MAR and
dipped beam headlights on, press the
+ button to adjust the headlights
upwards and the – button to adjust the
headlights downwards.
TYRE RESET (ITPMS
RESET)
(for versions/markets, where provided)
With this function it is possible to reset
the iTPMS (see paragraph “iTPMS”). To
carry out the Reset procedure proceed
as follows:
❒ briefly press the MENU
N; the
display will show “Reset”;
❒ press button + or – to select (“Yes”
or “No”); a dedicated reset
confirmation message will appear;
❒ briefly press the MENU
N; the
display will show “Confirm”;
THE KEYS1)
1) 1)
CODE CARD
(for versions/markets, where provided)
The car is delivered with two copies of
the ignition key and with the CODE
card fig. 7 which bears the following:
A: the electronic code;
B: the mechanical key code to be given
to the Fiat Dealership when ordering
duplicate keys.
You should have the electronic code
with you at all times.
IMPORTANT All the keys and the
CODE card must be handed over to
the new owner when selling the car.
MECHANICAL KEY
The metal insert A-fig. 8 operates:
❒ the ignition switch;
❒ the door locks and the tailgate (for
versions/markets, where provided);
❒ the locking/unlocking of the fuel
cap.
KEY WITH REMOTE
CONTROL
(for versions/markets, where provided)
The metal insert A-fig. 9 operates:
❒ the ignition switch;
❒ the door locks;
❒ the locking/unlocking of the fuel
cap.
7DVDF0S0103c
8DVDF0S0104c

35
With the selector switch in the AUTO
position, the side lights and dipped beam
headlights are controlled by the dusk
sensor.
MAIN BEAM
HEADLIGHTS
❒ With the ring in the 2position,
push the stalk forwards towards the
dashboard. The
1warning light on
the instrument panel will light.
❒ For vehicles with the AUTO
function: with the ring in the AUTO
position and the dipped beam
headlights on, push the stalk
forwards toward the dashboard.
❒ They are deactivated by pulling the
stalk towards the steering wheel.
Flashing
❒ You can flash the beams pulling the
stalk toward the steering wheel
(unstable position).
PARKING LIGHTS
These lights can be turned on with the
starter switch in the STOP position or
with the key removed, by moving the
left stalk ring first to the position (or
the AUTO position if the vehicle does
not have a dusk sensor) and then to
position
2.The warning light
3lights on the
instrument panel. Repeat the same
operation to switch them off.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
❒ up a: activates the right direction
indicator;
❒ down b: activates the left direction
indicator.
LANE CHANGE
FUNCTION
❒ Move the lever upwards or
downwards (unstable position) for
less than half a second and the
direction indicator will flash 3 times
to signal a lane change, then
immediately switch off
automatically.
FOLLOW ME HOME
This function allows the space
surrounding the car to be lit up for the
set period of time.
Activation
The “Follow Me Home” device is
activated by pulling the stalk fig. 25
towards the steering wheel, in addition
to the stroke end click.
EXTERNAL LIGHTS
DAYTIME RUNNING
LIGHTS
7)
❒ For vehicles with the AUTO
function: with the key in the MAR
position and the ring turned to the
O position, the daytime running
lights switch on automatically.
❒
For vehicles with the AUTO function:
the daytime running lights are turned
on automatically by the dusk sensor
when the ring is in the AUTO position.
DIPPED HEADLIGHTS/
SIDE LIGHTS
❒ With key at MAR, turn the ring nut to
2. The warning light
3on the
instrument panel will come on. When
the dipped beam headlights are on,
the daytime running lights switch off.
24
1
2
DVDF0S008c

KNOWING YOUR CAR
36
It is possible to enable this function
within 2 minutes after turning off the
engine. This function allows turning on
lights and low beams. It is possible to
set the headlights turning on time by
pulling the left lever towards the
steering wheel (unstable position) one
or more times. In this case it is
possible to choose between 0, 30, 60,
90 up to a maximum of 210 seconds.
Each time the stalk is operated, the
warning light
3on the instrument
panel switches on. The display shows
a message and the time set for the
function.
The
3warning light comes on when
the stalk is first moved and stays on
until the function is automatically
deactivated.
Deactivation
This function is deactivated turning on
again the headlights, sidelights or
pulling the left lever towards the
steering wheel (unstable position) for
more than 2 seconds, or switching the
starter to MAR.
AUTO FUNCTION
(Dusk sensor)
(for versions/markets, where provided)
This is an infrared LED sensor that works
in conjunction with the rain sensor. It is
located on the windscreen (fig. 25) and is
able to detect variations in outside
lighting based on the light sensitivity set
in the display Menu or the Uconnect™
5" or 7" HD system (where provided).
The higher the sensitivity, the lower the
amount of external light needed to
automatically switch the external lights
on.
25DVDF0S0215c
Function activation
Turn the left stalk ring A fig. 26 to the
AUTOposition.
IMPORTANT The function can only be
activated with the ignition device in the
MAR position.
Function deactivation
To deactivate the function, turn the left
stalk ring A to position 2.
26DVDF0S0216c

KNOWING YOUR CAR
48
Emergency braking
In the event of emergency braking the
hazard warning lights switch on
automatically as well as warning lights
andin the instrument panel.
The lights switch off automatically
when emergency braking ceases.
FRONT/REAR FOG
LIGHTS
(for versions/markets, where provided)
With the dipped beam headlights on,
to turn on the front/rear fog lights, use
the button A fig. 49 as follows:
❒ press once: fog lights on, warning
light
5appears on the instrument
panel;
48DVDF0S0180c
❒ press twice: rear fog lights on,
warning light
4appears on the
instrument panel;
❒ press three times: front/rear fog
lights off.
REAR FOG LIGHTS
(for versions/markets, where provided)
With the dipped beam headlights on,
turn on the rear fog lights pressing the
button B fig. 49. The
4warning light
on the instrument panel will come on.
Press the button again to switch the
lights off.
49DVDF0S0181c
ABS SYSTEM 15)
This system, which is an integral part
of the braking system, prevents one or
more wheels from locking and slipping
in any road surface condition,
irrespective of the intensity of the
braking action, ensuring that the car
can be controlled even during
emergency braking thus optimising
stopping distances.
SYSTEM INTERVENTION
The driver can feel that the ABS
system has come into action because
the brake pedal pulsates slightly and
the system gets noisier: this is entirely
normal with the system operating.

IN AN EMERGENCY
134
REPLACING A BULB
34) 19)
GENERAL
INSTRUCTIONS
❒ Before changing a bulb check the
contacts for oxidation;
❒ burnt bulbs must be replaced by
others of the same type and power;
❒ always check the headlight beam
aiming after changing a bulb;
❒ whenever a lamp does not work,
please check that the
corresponding fuse is in tact before
replacing it: please refer to the
paragraph “Replacing fuses” in this
chapter for the location of fuses.
IMPORTANT Whenever the weather is
hot or cold, of after heavy rain, the
surface of the headlights or rear lights
may steam up and/or form droplets of
condensation on the inside. This is a
natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside of
the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from the
centre of the diffuser, extending
progressively towards the edges.