2017 VOLVO XC90 TWIN ENGINE HYBRID ECO mode

DRIVER SUPPORT
}}
* Option/accessory, for more information, see Introduction.305

Additional information
•The Off Road drive mode cannot beselected if Pilot Assist is activated.
•Pilot Assist uses the vehicle's camera andradar sensor, which have certain general limi-tations. See the articles "Camera limitations"and "Radar sensor limitations" for additionalinformation.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-1* (p. 295)
•Starting and activating Pilot Assist-1*(p. 298)
•Setting a Pilot Assist-1 time interval (p. 300)
•Deactivating/resuming Pilot Assist-1(p. 301)
•Automatic braking with Pilot Assist-1(p. 303)
•Radar sensor limitations (p. 319)
•Camera limitations (p. 323)
Pilot Assist-2*
The Pilot Assist feature helps keep the vehicle inits current traffic lane by providing steeringassistance and maintaining an even speed and aset time interval to the vehicle ahead.
Function
Pilot Assist helps provide more relaxed driving onlong trips on highways or other major roads in aneven flow of traffic.
Function overview (generic illustration)
Windshield module containing the camera/radar sensor
Monitoring distance
Monitoring side marker lines
The driver sets the desired time interval to thevehicle ahead. Pilot Assist monitors that vehicleand the traffic lane's side market lines using the
camera and radar sensor mounted in the upper,center section of the windshield. It helps maintainthe set time interval by automatically adjustingspeed and by providing steering assistance tohelp keep your vehicle in the lane.
Pilot Assist's steering assistance is based onmonitoring the direction of the vehicle ahead andthe traffic lane's side marker lines. The driver canalways override Pilot Assist and steer the vehicleto e.g., change lanes, etc.
If the camera and radar sensor cannot detect thelane's side marker lines, Pilot Assist will tempo-rarily switch off the steering assistance until thelane's side marker lines become visible again andcan be detected. However, the function's speedand distance monitoring will continue to be acti-vated.

WARNING
Pilot Assist's steering assistance may switchon or off without warning.
The color of the steering wheelsymbol indicates the currentstatus of the steering assis-tance function:
WHITE: steering assistance isactive
GRAY (as in the illustration): steering assistanceis deactivated

DRIVER SUPPORT
}}
307

Pilot Assist overview
Controls
Function buttons and symbols (generic illustration)
Increase set speed or resume Pilot Assist setspeed and distance (time interval) to thevehicle ahead
Press to activate Pilot Assist or put it instandby mode
Change from Pilot Assist to Adaptive CruiseControl
Reduce set speed
Increase the distance (time interval) to thevehicle ahead
Change from Adaptive Cruise Control to PilotAssist
Reduce the distance (time interval) to thevehicle ahead
Function symbol
Distance and target vehicle symbol
Steering assistance symbol

Instrument panel
Speed indication (generic illustration)
Set speed
Speed of the vehicle ahead
Your vehicle's current speed.
See also the article "Pilot assist symbols andmessages" for additional information.
Collision warning
Warning light in the windshield
Pilot Assist can exert brake force that is equiva-lent to approximately 40% of the vehicle's totalbraking capacity.
In situations requiring more brake force than PilotAssist can provide and if the driver does notapply the brakes, an audible signal and warninglight will illuminate in the windshield to alert thedriver to react.

NOTE
Strong sunlight, reflections, extreme light con-trasts, the use of sunglasses, or if the driver isnot looking straight ahead may make the vis-ual warning signal in the windshield difficult tosee.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.310
•the lane is at the top of a hill, on anuneven road surface or over a bump.
•bad weather conditions (rain, snow, fog,slush, poor visibility, backlighting, etc).
The driver should also be aware that PilotAssist has the following limitations:
•High curbs, barriers and temporary obsta-cles (cones, barriers etc) may not bedetected or could be detected incorrectlyas side marker lines, which may create arisk of collision. The driver must ensure asafe distance to these obstacles.
•The camera or radar sensor may not beable to detect objects if there are pot-holes or if there are stationary objectspartially or completely blocking the road.
•Pilot Assist does not "see" pedestrians,animals, etc.
•Pilot Assist's steering capacity is limitedand may not always be able to help thedriver keep the vehicle in the lane.

Hands on the steering wheel
Pilot Assist only functions when the driver'shands are on the steering wheel, which is con-tinuously monitored by the system. If this is notthe case, the driver will be alerted by a text mes-sage in the instrument panel. If the driver's handsare not returned to the steering wheel, an audiblesignal will sound.
If the driver does not return his/her hands to thesteering wheel after the audible signal, Pilot
Assist will go into standby mode and must be
reactivated by pressing .
Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Changing Pilot Assist-2 speed
Different speeds can be set for Pilot Assist.
Function buttons and symbols
–Change a set speed by pressing the (1)or — (3) buttons briefly or by pressing andholding them:
•Press briefly: changes speed in+/– 5 mph (+/– 5 km/h) increments.Each press changes the vehicle's speedby +/– 5 mph (+/– 5 km/h).
•Press and hold: changes the speed+/– 1 mph (+/– 1 km/h) at a time.Release the button when the set speedindicator (4) has moved to the desiredspeed.
If speed is increased by pressing the accelerator
pedal before the button is pressed, the vehi-cle's speed when the button is pressed will

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.312
Time interval controls
Press to reduce the time interval to the vehi-cle ahead
Press to increase the time interval to thevehicle ahead
Distance indicator
In order to follow the vehicle ahead as smoothlyas possible, Pilot Assist allows the time interval tovary considerably in certain situations. At lowspeeds, when the distance to the vehicle aheadis short, Pilot Assist increases the time intervalslightly.
•If Pilot Assist does not seem to react when itis put in active mode, this may be becausethe set time interval to the vehicle aheaddoes not allow an increase in speed.
•The higher the speed, the greater the dis-tance to the vehicle ahead for a given timeinterval.

WARNING
•Only use a time interval that is suitable incurrent traffic conditions.
•A short time interval gives the driver lim-ited reaction time if an unexpected situa-tion occurs in traffic.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Deactivating/resuming Pilot Assist
Pilot Assist can be temporarily deactivated, putin standby mode and then reactivated.
Function buttons and symbols (generic illustration)

Deactivating and putting Pilot Assist in
standby mode
–Press the button (2).
>Pilot Assist will go into standby mode. The
symbol in the instrument panel willchange colors from WHITE to GRAY andthe set speed in the center of the speed-ometer will change from BEIGE to GRAY.
or
–Press the ◀ button (2).
>Pilot Assist will be turned off and shift toAdaptive Cruise Control in active mode.

DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.314
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
•Distance Alert* (p. 279)
Changing target vehicles andautomatic braking with PilotAssist-2
At certain speeds, Pilot Assist can change targetvehicles and automatically apply the brakes.

Changing target vehicles
If the target vehicle turns suddenly, there may be a sta-tionary vehicle ahead
When Pilot Assist is actively following anothervehicle at speeds under 20 mph (30 km/h) andchanges targets from a moving vehicle to a sta-tionary one, the system will brake for the station-ary vehicle.
WARNING
If Pilot Assist changes targets from a movingvehicle to a stationary one at speeds above20 mph (30 km/h), the system will not reactto the stationary vehicle and will accelerate tothe previously set speed.
The driver must actively apply the brakes toslow/stop the vehicle.

Automatic standby mode when changing
targets
Pilot Assist disengages and goes into standbymode if:
•your vehicle's speed goes below approx.3 mph (5 km/h) and Pilot Assist cannotdetermine if the target object is a stationaryvehicle or some other type of object such asa speed bump, etc
•the vehicle's speed goes below approx.3 mph (5 km/h) and the vehicle aheadchanges lanes or turns so that Pilot Assistno longer has a target vehicle to follow

Auto-hold brake function
In slow-moving, stop-and-go traffic or when stop-ped at a traffic light, driving will resume automati-cally if the vehicle is not stopped for more thanapprox. 3 seconds. If it takes more than3 seconds for the vehicle ahead to begin movingagain, Pilot Assist will go into standby mode andthe auto-hold brake function will activate.

DRIVER SUPPORT
}}
* Option/accessory, for more information, see Introduction.315
–The driver will then have to reactivate PilotAssist in one of the following ways:
•Press the button on the left-sidesteering wheel keypad
•Press the accelerator pedal
>Pilot Assist will resume following the vehi-cle ahead (target vehicle) if it begins tomove within approx. 6 seconds.

NOTE
Pilot Assist can keep the vehicle at a stand-still for up to 5 minutes, after which the park-ing brake will be set and Pilot Assist will gointo standby mode.
The parking brake has to be released beforePilot Assist can be reactivated.

Deactivation of the auto-hold brake function
In certain situations, auto-hold will be deactivatedwhen the vehicle is at a standstill and Pilot Assistwill go into standby mode.
This means that the brakes will be released andthe vehicle can begin to roll.
The driver must actively apply the brakes to keepthe vehicle at a standstill.
This can occur in the following situations:
•the driver presses the brake pedal
•the parking brake is set
•the gear selector is moved to the P, N or Rpositions
•the driver puts Pilot Assist in standby mode
Automatically setting the parking brake
In certain situations, the parking brake is setautomatically to help keep the vehicle at a stand-still.
This occurs if Pilot Assist keeps the vehicle at astandstill with the brakes and:
•the driver unbuckles the seat belt or opensthe door
•Pilot Assist has kept the vehicle at a stand-still for more than approx. 5 minutes
•the engine is turned off
•the brakes overheat

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 limitations (p. 315)
•Pilot Assist-2 symbols and messages(p. 317)
Pilot Assist-2 limitations
Pilot Assist functionality may be limited in certainsituations.
Pilot Assist is designed to help the driver in anumber of situations. However, the driver alwayshas the primary responsibility for maintaining asafe distance to other vehicles and for keepingthe vehicle in its proper traffic lane.

||
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.316

WARNING
Pilot Assist is not a collision avoidance sys-tem. The driver is always responsible forsteering or applying the brakes if the systemdoes not detect another vehicle.
Do not use Pilot Assist in demanding drivingconditions such as city driving or other heavytraffic situations, in slippery conditions, whenthere is a great deal of water or slush on theroad, during heavy rain or snow, in poor visibil-ity, on winding roads or on highway on- or off-ramps.
In certain situations, it may be difficult for PilotAssist to assist the driver correctly or to deac-tivate automatically. In such cases, it is advisa-ble not to use Pilot Assist. Examples of suchsituations may be:
•the lane's side market lines are missing,badly faded or cross each other.
•the division of lanes is not clear, e.g.,when a line divides or merges withanother, at exits or if there are many roadsigns/markers.
•there are edges or other lines on or nearthe lane, e.g., curbs, cracks, repairedareas, sharp shadows, etc.
•the lane is narrow or winding.
•the lane is at the top of a hill, on anuneven road surface or over a bump.
•bad weather conditions (rain, snow, fog,slush, poor visibility, backlighting, etc).
The driver should also be aware that PilotAssist has the following limitations:
•High curbs, barriers and temporary obsta-cles (cones, barriers etc) may not bedetected or could be detected incorrectlyas side marker lines, which may create arisk of collision. The driver must ensure asafe distance to these obstacles.
•The camera or radar sensor may not beable to detect objects if there are pot-holes or if there are stationary objectspartially or completely blocking the road.
•Pilot Assist does not "see" pedestrians,animals, etc.
•Pilot Assist's steering capacity is limitedand may not always be able to help thedriver keep the vehicle in the lane.
The driver can always take action to override PilotAssist.

Steep roads and/or heavy loads
Pilot Assist is primarily intended for use on rela-tively level roads. The function may not be able tomaintain the correct time interval to the vehicleahead on when driving down steep hills. Thedriver should be attentive and prepared to applythe brakes in these situations.
Do not use Pilot Assist when the vehicle is trans-porting a heavy load or if it is towing a trailer.
Additional information
•The Off Road drive mode cannot beselected if Pilot Assist is activated.
•Pilot Assist uses the vehicle's camera andradar sensor, which have certain general limi-tations. See the articles "Camera limitations"and "Radar sensor limitations" for additionalinformation.

Related information
•Pilot Assist* (p. 295)
•Pilot Assist-2* (p. 305)
•Starting and activating Pilot Assist-2 (p. 308)
•Changing Pilot Assist-2 speed (p. 310)
•Setting a Pilot Assist-2 time interval (p. 311)
•Changing target vehicles and automaticbraking with Pilot Assist-2 (p. 314)
•Deactivating/resuming Pilot Assist (p. 312)
•Passing Assistance with Adaptive CruiseControl or Pilot Assist-2 (p. 289)
•Pilot Assist-2 symbols and messages(p. 317)
•Radar sensor limitations (p. 319)
•Camera limitations (p. 323)

DRIVER SUPPORT
}}
351
Driving lane assistance provide vibrations in the steeringwheel8.
Depending on the settings used, Lane KeepingAid functions in different ways:
•Assistance type Steering9 is activated: whenthe vehicle approaches a traffic lane markerline, LKA will provide active steering assis-tance to help steer it back into the lane.
•Assistance type Warning9 is activated: if thevehicle is moving out of its traffic lane, anaudible signal and/or vibrations in the steer-ing wheel will be provided.

NOTE
If the turn signal is used, Lane Keeping Aidwill not provide an alert or steering assis-tance.

WARNING
Lane Keeping Aid is only intended to assistthe driver and does not function in all driving,weather, traffic or road conditions.
As the driver, you have full responsibility foroperating the vehicle in a safe manner.

Steering assistance
In order for LKA's steering assistance to function,the driver's hands must be on the steering wheel,which the system monitors continuously.
If the driver's hands are not onthe steering wheel, this symbolwill illuminate in the instrumentpanel and the following mes-sage will be displayed:
•Lane Keeping Aid – Apply steering
If the driver does not begin to steer the vehicle,the symbol will illuminate again, an audible signal
will sound and the following message will be dis-played:
•Lane Keeping Aid – Standby untilsteering applied
If the driver still does not begin to steer the vehi-cle, LKA will go into standby mode. The functionwill not become available again until the driveractively steers the vehicle
Lane assistance do not react
The traffic lane assistance system do not intervene insharp curves
In certain cases, such as during active driving or ifthe turn signal is used, the traffic lane system willnot react if the vehicle crosses a lane markerline.
8The level of vibrations varies; the farther the vehicle is over a lane marker line, the greater the number of vibrations:9See "Type of assistance" in the article "Activating/deactivating Lane Keeping Aid".