2017 SUZUKI CELERIO Owners Manual

2-3
BEFORE DRIVING
76MH1-74E
76MH1-74E
NOTE: You can switch the function that unlocks alldoors from twice operations to once opera- tion, and vice versa, via the setting modeof the information display. For details onhow to use the information display, refer to“Information Display” in this section.
To unlock the driver’s door only, insert the key in that door lock and turn the top of thekey toward the rear of the vehicle once.
76MH0A020
(1) LOCK (2) UNLOCK
You can also lock or unlock all doors by depressing the front or rear of the switch(3), respectively.
NOTE: If your vehicle is equipped with keyless entry system, you can also lock or unlockall doors by operating the transmitter. Refer to “Keyless Entry System Transmit- ter” in this section.
NOTE: • All doors are automatically unlockedwhen you turn the ignition switch to the “LOCK” position and pull out the key.• All doors are automatically locked forsafety when the vehicle speed reaches15 km/h.• You can change the automatic locking orunlocking function mentioned above viathe setting mode of the information dis- play. For details on how to use the infor-mation display, refer to “Information Display” in this section.
Child-Proof Locks (rear door)
76MH0A021
(1) LOCK (2) UNLOCK
Each of the rear doors is equipped with achild-proof lock which can be used to help prevent unwanted opening of the door from inside the vehicle. When the lock lever is inthe “LOCK” position (1), the rear door can only be opened from outside. When the lock lever is in the “UNLOCK” position (2),the rear door can be opened from inside or outside.
(1)
(2)
(3)
EXAMPLE
WA R N I N G
Be sure to place the child-proof lockin the “LOCK” position whenever children are seated in the rear.
(1)
(2)
EXAMPLE
14

2-4
BEFORE DRIVING
76MH1-74E
76MH1-74E
Ta i l g a t e
76MH0A086
(1) Driver’s door lock (2) Tailgate lock (3) Tailgate handle
If your vehicle is equipped with the cen-tral door locking system, you can lock orunlock the tailgate by using the key in the driver’s door lock (1).
If your vehicle is not equipped with thecentral door locking system, you can lock or unlock the tailgate by using thekey in the tailgate lock (2).
To open the tailgate, pull up the tailgatehandle (3) and lift the tailgate.
If you cannot unlatch the tailgate by pulling up the tailgate handle (3) due to a dis- charged battery or malfunction, follow the procedures below to unlatch the tailgatefrom inside the vehicle. 1) Remove the luggage compartmentcover (if equipped) and fold the rear seat forward for easier access. Refer to “Folding Rear Seats” section for details on how to fold the rear seat forward.
76MH0A099
2) Remove the trim (5) of the tailgate. Push center of the clips (4) and pullthem out. Then, remove the trim (5).
76MH0A137
3) To unlock the tailgate lock, pull the lockplate (6) up. To open the tailgate, pushthe emergency lever (7) sideways. Thetailgate will be latched again by simply closing the tailgate.
If the tailgate cannot be unlatched by pull-ing up the tailgate handle (3), have the vehicle inspected by your MARUTISUZUKI dealer.
WA R N I N G
Always make sure that the tailgate is closed and latched securely. Com- pletely closing the tailgate helps pre-vent occupants from being thrown from the vehicle in the event of an accident. Completely closing it alsohelps keep exhaust gases from enter- ing the vehicle.
(3)
(1)
(2)
EXAMPLE
(5)
(4)
CAUTION
Make sure there is no one near the tailgate when pushing open the tail- gate from inside the vehicle. To avoid injury, do not use your fin-ger to push the emergency lever.
(6)
(7)
15

2-5
BEFORE DRIVING
76MH1-74E
76MH1-74E
Keyless Entry System
Transmitter (if equipped)
76MS011
(1) “LOCK” button (2) “UNLOCK” button
You can lock or unlock all doors (includingthe tailgate) simultaneously by operating the transmitter near the vehicle.
To lock all doors, push the “LOCK” but-ton (1) once. To unlock only the driver’s door, push the“UNLOCK” button (2) once. To unlock other doors, push the“UNLOCK” button (2) once again.
NOTE: You can switch the function that unlocks alldoors from twice operations to once opera- tion, and vice versa, via the setting modeof the information display. For details onhow to use the information display, refer to“Information Display” in this section.
The turn signal lights will flash once and the siren (if your vehicle is equipped with the security system) will sound once whenthe doors are locked.
When the doors are unlocked: The turn signal lights will flash twice andthe siren (if your vehicle is equipped withthe security system) will sound twice. If the interior light switch is in the“DOOR” position, the interior light willturn on for about 15 seconds and thenfade out. If you insert the key into the ignition switch during this time, the light will start to fade out immediately.
Be sure the doors are locked after youoperate the “LOCK” button. If no door isopened within about 30 seconds after the “UNLOCK” button is operated, the doors will automatically lock again.
NOTE: (For models with security system)• If you lock the doors using the transmit-ter when the engine hood is open, thesiren will sound 3 times to remind you.• If the security system was triggered dueto an unauthorized entry into the vehicleand then you unlock the doors using thetransmitter, the siren will sound 4 times to remind you. If this happens, check whether your vehicle has been brokeninto while you were away from it.• Once you push both of the “LOCK” but-ton (1) and “UNLOCK” button (2), thenyou push one of the buttons within 5 sec-
onds, the siren will not sound. However, If you push one of the buttons twice within 5 seconds, or push one of the but-tons 5 seconds later, the siren willsound.• You can set whether the siren soundswhen locking or unlocking the door(s) via the setting mode of the information dis- play. For details on how to use the infor-mation display, refer to “InformationDisplay” in this section.
NOTE: • The maximum operating distance of thekeyless entry system transmitter is about 15 m (48 ft.), but this can vary depending on the surroundings, especially near other transmitting devices such as radiotowers or CB (Citizen’s Band) radios.• The door locks cannot be operated withthe transmitter if the ignition key isinserted in the ignition switch.• If any door is open, you cannot lock thedoor by operating the transmitter, how-ever unlock the door.• If you lose one of the transmitters, askyour MARUTI SUZUKI dealer as soonas possible for a replacement. Be sure to have your dealer program the new transmitter code in your vehicle’s mem-ory so that the old code is erased.
(1)
(2)
16

2-6
BEFORE DRIVING
76MH1-74E
76MH1-74E
Panic alarm function (if equipped)This function is to get the attention of oth- ers. Push both of the “LOCK” button (1) and “UNLOCK” button (2) for more than 3 sec-onds. The turn signal lights will blink for about 27.5 seconds. Also, the siren will sound for about 27.5 seconds at the sametime. To cancel the panic alarm, press any but- ton (LOCK or UNLOCK). You can also turnthe ignition switch to the “ON” position to cancel the panic alarm.
NOTE: The panic alarm function will not activate when the key is in the ignition switch.
Replacement of the Battery If the transmitter becomes unreliable, replace the battery.
To replace the battery of the transmitter:
68LM248
1) Remove the screw (1), and open thetransmitter cover.2) Remove the transmitter (2).
68LM249
(3) Lithium disc type battery:CR1616 or equivalent
3) Put the edge of a flat blade screwdriverin the slot of the transmitter (2) and pry it open.4) Replace the battery (3) so its + terminalfaces the “+” mark of the transmitter.5) Close the transmitter and install it intothe transmitter holder.6) Close the transmitter cover, install andtighten the screw (1).7) Make sure the door locks can be oper-ated with the transmitter.8) Dispose of the used battery properlyaccording to applicable rules or regula- tions. Do not dispose of lithium batter- ies with ordinary household trash.
NOTICE
The transmitter is a sensitive elec-tronic instrument. To avoid damagingthe transmitter: • Do not expose it to impacts, mois-ture or high temperature such as by leaving it on the dashboard under direct sunlight.• Keep the transmitter away frommagnetic objects such as a televi-sion.• Do not tamper with internal parts.
(1)
(2)
(2)
(3)
WA R N I N G
Swallowing a lithium battery may cause serious internal injury. Do notallow anyone to swallow a lithium battery. Keep lithium batteries away from children and pets. If swallowed,contact a physician immediately.
NOTICE
The transmitter is a sensitive elec- tronic instrument. To avoid damaging it, do not expose it to dust or mois-ture or tamper with internal parts.
17

2-7
BEFORE DRIVING
76MH1-74E
76MH1-74E
Security System (if equipped)
The security system is armed in about 5 seconds after you lock all doors (includingthe tailgate) by using the keyless entry sys- tem transmitter. Once the system is armed, any attempt toopen a door by using any other means (*) than the keyless entry system transmitter, or open the engine hood, will cause thealarm to be triggered. * These means include the following:–The key – The lock knob on a door – The central door locking switch
Also, in case that you have set the shocksensor to enabled state and set sensitivity of the pre-warning function and full blastwarning function to a level other than 0, the alarm will be triggered if any attempt to tamper with the vehicle. The shock sensorcan be selected enabled or disabled state, and sensitivity of each warning can be adjusted as desired. To set the shock sen-sor, ask your MARUTI SUZUKI dealer or use the setting mode of the information display.
NOTE: • The default setting of the shock sensoris in the disabled state. Set to the enabled state and adjust sensitivity of each warning according to your prefer- ence. For details on how to use the infor-mation display, refer to “Information Display” in this section.• Your dealer may have already set theshock sensor of the vehicle to theenabled state before you purchase it. Consult your dealer for further informa-tion.
NOTE:• The security system generates alarmswhen any of the predetermined condi-tions is met. However, the system doesnot have any function of blocking unau- thorized entry into the vehicle.• Always use the keyless entry systemtransmitter to unlock the doors when thesecurity system has been armed. Using a key instead will trigger the alarm.• If a person who does not know the secu-rity system is going to drive the vehicle,we recommend you explain the systemand its operation to the person, or dis- able the system beforehand. Mistakenly triggering the alarm may cause a nui-sance to others.• Even if the security system is armed,you should still be careful to guardagainst theft. Do not leave money or things of value in the vehicle.
How to arm the security system
(when enabled)Lock all doors (including the tailgate) using the keyless entry system transmitter. Thesecurity system indicator (1) will start blink- ing rapidly, and the security system will be armed in about 5 seconds.While the system is being armed, the indi- cator continues to blink at intervals of approximately 2 seconds.
With tachometer
76MH0B001
(1)
18

2-8
BEFORE DRIVING
76MH1-74E
76MH1-74E
Without tachometer
76MH0B002
NOTE: • To prevent the alarm from being acci-dentally triggered, avoid arming it while anyone remains inside the vehicle. The alarm will be triggered if any person inside opens the door or engine hood, orswings the vehicle (if the shock sensor is in the enabled state).• The security system is not armed whenall doors are locked using the key fromoutside, or using the door lock knobs or the central door locking switch frominside.• If any door is not operated within approx-imately 30 seconds after the doors havebeen unlocked using the keyless entry system transmitter, the doors are auto-matically locked again. When the doors are locked, the security system will be
armed in about 5 seconds if the system is in the enabled state.• If the security system indicator (1) blinkswhen the ignition switch is in the “ON”position, there may be something wrong with the security system. Ask your MAR-UTI SUZUKI dealer to inspect the sys- tem.
How to disarm the security systemSimply unlock the doors using the keyless entry system transmitter. The security sys-tem indicator will go out, indicating that the security system is disarmed.
How to stop the alarm Should the alarm be triggered accidentally, unlock the doors using the keyless entrysystem transmitter, or insert the key in the ignition switch and turn it to “ON” position. The alarm will then stop.
NOTE: • Even after the alarm has stopped, if youlock the doors using the keyless entry system transmitter, the security system will be rearmed with a delay of about 5seconds.• If you disconnect the battery while thesecurity system is in the armed conditionor the alarm is actually in operation, the alarm will be re-triggered when the bat- tery is then reconnected.• Even after the alarm has stopped at theend of the predetermined operation time,it will be triggered again if any of thedoors or engine hood is opened, or the
vehicle feels a shock (if the shock sen- sor is in the enabled state), without dis- arming the security system.
Checking whether the alarm has beentriggered during parkingIf the alarm was triggered and you then turn the ignition switch to “ON” position, the security system indicator will blink rapidlyfor about 8 seconds and a buzzer will beep 4 times during this period. If this happens, check whether the vehicle has been bro-ken into while you were away from it.
Enabling and disabling the security system The security system can be either enabled or disabled.
When enabled If any of the doors are opened withoutunlocking by the keyless entry system transmitter, all turn signal lights start to blink and the interior buzzer beeps inter-mittently. After 5 seconds, the siren will sound for about 27.5 seconds. The secu- rity system indicator continues to blinkduring this time. If the engine hood is opened, all turn sig-nal lights blink, and the siren sounds forabout 27.5 seconds. The security sys- tem indicator continues to blink during this time.
(If the shock sensor is in the enabled state) If the vehicle feels a shock, the sirensounds for about 2 seconds (pre-warn- ing). If the vehicle continues to feel a
(1)
19

2-9
BEFORE DRIVING
76MH1-74E
76MH1-74E
shock, all turn signal lights start to blink and the interior buzzer beeps intermit- tently. After 5 seconds, the siren willsound for about 27.5 seconds (full blast warning). The security system indicator continues to blink during this time.
NOTE:If you set the full blast warning sensitivityhigher than the pre-warning sensitivity inthe setting mode of the information display,or the vehicle feels such shock as to beable to trigger the full blast warning, the full blast warning will be triggered preferen- tially. In this case, the pre-warning will notbe triggered.
When disabled When the system is disabled, it stays dis- armed even if you perform any system arming operation.
How to switch the state of the security systemWhen the security system has beenalready disarmed, you can switch the sys-tem from the enabled state to the disabledstate, and vice versa, using the following method.
1) Sit in the driver

2-10
BEFORE DRIVING
76MH1-74E
76MH1-74E
4) Push the lock end (4) (forward end) ofthe central door locking switch (5), and then push the unlock end (6) (backwardend). Repeat this operation 3 times.
Every time you perform the series of theabove steps, the state of the security sys- tem changes from the currently selected one to the other. You can check whetherthe system is enabled or disabled by the number of interior buzzer beeps at the end of the procedure as follows.
If you cannot complete the operations instep 3) and 4) within 15 seconds cor- rectly, the state of the security systemwill not change and the interior buzzer does not beep. Perform the procedure again from the beginning.
NOTE: You can also switch the security systemfrom the enabled state to the disabled state, and vice versa, via the setting mode of the information display. For details onhow to use the information display, refer to“Information Display” in this section.
Windows
Manual Window Control
(if equipped)
60G010
Raise or lower the door windows by turning the handle located on the door panel.
Electric Window Controls
(if equipped)The electric windows can only be operated when the ignition switch is in the “ON” posi- tion.
Driver’s door
76MH0A022
The driver’s door has a switch (1) to oper- ate the driver’s window, and a switch (2) tooperate the front passenger’s window or there are switches (4), (3), to operate the rear left and right passenger windows,respectively.
Passenger’s door
76MH0A023
The passenger’s door has a switch (5) to operate that passenger’s window.
81A009
System state Number of beeps
DisabledOnce
Enabled 4 times
EXAMPLE
(1)(2)
(3)
(4)
EXAMPLE
(5)EXAMPLE
CLOSE
OPEN
21