2017 NISSAN QASHQAI Owner´s Manual

2-18Instruments and controls
Light reminder chime
The light reminder chime will sound when the
driver side door is opened with the headlight
switch in the
orposition, and the
ignition switch is in the ACC, OFF or LOCK
position.
Turn the light switch off when you leave the
vehicle.
NISSAN Intelligent KeyŠdoor buzzer (if
so equipped)
The Intelligent Key door buzzer sounds if any
one of the following improper operations is
found.
.The Intelligent Key is left inside the vehicle
when locking the doors.
.The Intelligent Key is left outside the vehicle
when operating the vehicle.
When the buzzer sounds, be sure to check both
the vehicle and the Intelligent Key. For additional
information, refer to “Intelligent Key system”
(P.3-11) .
Brake pad wear warning
The disc brake pads have audible wear warn-
ings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound will
first occur only when the brake pedal isdepressed. After more wear of the brake pad,
the sound will always be heard even if the brake
pedal is not depressed. Have the brakes
checked as soon as possible if the warning
sound is heard.
Parking brake reminder chime
The parking brake reminder chime will sound if
the vehicle is driven at more than 4 MPH (7
km/h) (models not equipped with electronic
parking brake) or 2 MPH (4 km/h) (models
equipped with electronic parking brake) with the
parking brake applied. Stop the vehicle and
release the parking brake.
Seat belt warning chime
The seat belt warning chime will sound for about
6 seconds unless the driver’s seat belt is
securely fastened.
JVI0641X
The vehicle information display*1is located
between the tachometer and the speedometer,
and it displays the warnings and information. The
following items are also displayed if the vehicle
is equipped with them:
.Vehicle settings
.Trip computer information
.Driver Assistance
.Cruise control system information
.Intelligent Cruise Control (ICC) system
.Intelligent Key operation information
.Audio information
.Navigation - turn by turn
VEHICLE INFORMATION DISPLAY

.Indicators and warnings
.Tire pressure information
.Chassis Control
.Other information
JVI1566X
HOW TO USE THE VEHICLE INFOR-
MATION DISPLAY
The vehicle information display can be changed
using the buttons OK
*1,*2,*3,
and
*4located on the steering wheel.
*1OK - change or select an item in the vehicle
information display
*2- navigate through the items in vehicle
information display
*3- go back to the previous menu
*4- change from one display screen to
the next (i.e. trip, Fuel economy)
STARTUP DISPLAY
When the ignition switch is placed in the ON
position, the screens that display in the vehicle
information display include:
.Trip computer
.Fuel economy
.Warnings
Warnings will only display if there are any
present. For more information on warnings and
indicators, see “Vehicle information display
warnings and indicators” (P.2-28) .
To control what items display in the vehicle
information display, see “Settings” (P.2-19) .
SETTINGS
The setting mode allows you to change the
information displayed in the vehicle information
display:
.Driver Assistance (if so equipped)
.Clock
.Meter Settings
.Vehicle Settings
.Maintenance
.Alarm (if so equipped)
.Tire Pressures
.Unit
.Language
Instruments and controls2-19

2-20Instruments and controls
.Factory Reset
Driver Assistance (if so equipped)
To change the status, warnings or turn on or off
any of the systems/warnings displayed in the
“Driver Assistance” menu, use the
buttons
*2to select and the OK*1to change a menu
item:
.Driving Aids (if so equipped)
.Parking Aids (if so equipped)
.Chassis Control (if so equipped)
.Power Steering (if so equipped)
Driving Aids (if so equipped) :
To change the status, warnings or turn on or off
any of the systems/warnings displayed in the
“Driving Aids” menu, use the
buttons*2to
select and the OK
*1to change a menu item:
.Emergency Brake (if so equipped)
— Press the OK
*1to turn the Forward
Emergency Braking (FEB) system ON/
OFF.
.Lane (if so equipped)
— Warning
Press the OK
*1to turn the Lane Departure
Warning (LDW) system ON/OFF.
.Blind Spot (if so equipped)
— Warning
Press the OK
*1to turn the Blind SpotWarning (BSW) system ON/OFF.
For additional information, see “Forward Emer-
gency Braking (FEB)” (P.5-80) , “Forward Emer-
gency Braking (FEB) with pedestrian detection
system” (P.5-86) , “Lane Departure Warning
(LDW)” (P.5-31) and “Blind Spot Warning
(BSW)” (P.5-42).
Parking Aids (if so equipped):
To change the status or turn on or off any of the
systems displayed in the “Parking Aids” menu,
use the
buttons*2to select and the OK
*1to change a menu item:
.Moving Object (if so equipped)
Press the OK
*1to turn the Moving Object
Detection (MOD) ON/OFF.
.Cross Traffic (if so equipped)
Press the OK
*1to turn the Rear Cross
Traffic Alert (RCTA) ON/OFF.
For additional information, see “Moving Object
Detection (MOD)” (P.4-25)and “Rear Cross
Traffic Alert (RCTA)” (P.5-51) .
Chassis Control:
To change the status, warnings or turn on or off
any of the systems/warnings displayed in the
“Chassis Control” menu.
Use the
buttons*2to select and the OK
*1to change a menu item:.Trace Control
— See “Active Trace Control” (P.5-106) for
more information.
.Engine Brake (if so equipped)
— See “Active Engine Brake (Continuously
Variable Transmission (CVT) models)”
(P.5-107) for more information.
Press the OK
*1to turn ON/OFF.
Power Steering:
Use the
buttons*2to select and the OK
*1to change a menu item:
.NORMAL
The NORMAL mode is recommended for
normal driving.
.SPORT
The SPORT mode adjusts the steering to
enhance performance.
Clock
To set the clock, see “Displaying settings menu”
(P.4-5) , “Audio main operation” (P.4-48) or
“Audio main operation” (P.4-63) in this manual
or the separate Navigation System Owner’s
Manual (if so equipped) .

Meter Settings
The meter settings allows the customer to
choose from the various meter selections.
The meter settings can be changed using the
*2and the OK*1buttons.
Main Menu Selection:
The items that display when the ignition switch is
placed in the ON position can be enabled/
disabled. To change the items that are dis-
played, use the
*2to scroll and the OK*1
to select a menu item.
Body Color:
The color of the vehicle that displays in the
vehicle information display when the ignition
switch is placed in the ON position can be
changed.
1. Use the
buttons*2until “Body Color”
is selected, and press OK
*1.
2. Select the body color using the
buttons
*2and press OK*1.
ECO Mode Settings:
This setting allows the customer to change the
ECO mode system settings.
Use the
buttons*2until “ECO Mode
Settings” is selected, and press OK
*1.
- ECO IndicatorThis setting allows the customer to enable/
disable the ambient ECO indicator in the vehicle
information display.
1. Use the
buttons*2to select “ECO
Indicator”.
2. Press the OK
*1to turn ON/OFF the
ambient ECO in the vehicle information
display.
- DISP Mode
JVI0665X
This setting allows the customer to enable/
disable the ECO pedal guide function.
1. Use the
buttons*2to select “DISP
Mode”.
2. Press the OK
*1to select “Pedal” or “Inst.
FE.”.
For detailed information, see “ECO mode
system” (P.5-29) .
ECO Drive Report:
- Display
This setting allows the customer to enable/
disable the ECO Drive Report in the vehicle
information display.
Instruments and controls2-21

2-22Instruments and controls
1. Use thebuttons*2to select “Display”.
2. Press the OK
*1to turn ON/OFF the ECO
management display in the vehicle informa-
tion display.
- View History
This setting allows the customer to reset the
past history of the fuel economy and the best
fuel economy.
Welcome Effect:
You can choose whether or not to display the
welcome screen when the ignition switch is
placed in the ON position. You can also choose
the following items to define how the welcome
screen looks:
.Dial Effect
.Display Effect
Select “Welcome Effect” using the
buttons
*2and press the OK*1to select this menu.
Use thebuttons*2to navigate between
the menu options and press the OK
*1to turn
each function ON/OFF.
Vehicle Settings
The vehicle settings allows the customer to
change settings for the following settings.
.Lighting
.Turn indicator
.Locking
.Wipers
.Remote start (if so equipped)
The vehicle settings can be changed using the
*2, and the OK*1buttons.
Lighting:
The “Lighting” menu has the following options:
.Welcome Light
The welcome lighting can be set to be ON
or OFF. From the “Lighting” menu, select
“Welcome Light”. Use the OK
*1to turn
this feature ON or OFF.
.Auto Room Lamp
The interior light timer can be set to be ON
or OFF. From the “Lighting” menu, select
“Auto Room Lamp”. Use the OK
*1to turn
this feature ON or OFF.
.Light Sensitivity (if so equipped)
The sensitivity of the automatic lighting can
be adjusted. From the “Lighting” menu,
select “Light Sensitivity”. Use the
buttons*2and the OK*1to select therequired sensitivity. The following options
are available:
— Turn on earliest
— Turn on earlier
— Turn on standard
— Turn on later
.Light Off Delay (if so equipped)
The duration of the automatic headlights can
be changed from 0 to 180 seconds. From
the “Lighting” menu, select “Light Off
Delay”. Use the OK
*1to change the
duration.
Turn indicator:
The “3 Flash Pass” overtaking feature can be set
to be ON or OFF. From the “Turn indicator”
menu, select “3 Flash Pass”. Use the OK
*1to
turn this feature ON or OFF.
Locking:
There are the following options in the “Locking”
menu:
.I–Key Door Lock (if so equipped)
When this item is turned on, the request
switch on the door is activated. From the
“Locking” menu, select “I-Key Door Lock”.
Use the OK
*1to activate or deactivate this
function.

.Selective Unlock
When this item is turned on, and the door
handle request switch on the driver’s or front
passenger’s side door is pushed, only the
corresponding door is unlocked. All the
doors can be unlocked if the door handle
request switch is pushed again within 1
minute. When this item is turned to off, all
the doors will be unlocked when the door
handle request switch is pushed once. From
the “Locking” menu, select “Selective Un-
lock”. Use the OK
*1to activate or
deactivate this function.
.Auto Door Unlock
The “Auto Door Unlock” feature allows the
customer to customize the auto door unlock
options.
— Ignition OFF
— Shift to Park (for Continuously Variable
Transmission (CVT) models)
— Off
.Answer Bk. Horn (if so equipped)
When the answer back horn is on, the horn
will chirp and the hazard indicators will flash
twice when locking the vehicle with the
Intelligent Key or remote keyless entry
function.Wipers:
.Speed Dependent
The “Speed Dependent” feature can be
activated or deactivated. From the “Wipers”
menu, select “Speed Dependent”. Use the
OK
*1to turn this feature ON or OFF.
.Reverse Link
The “Reverse Link” wiper feature can be set
to be ON or OFF. From the “Wipers” menu,
select “Reverse Link”. Use the OK
*1to
turn this feature ON or OFF.
.Drip wipe
The “Drip wipe” feature can be set to be ON
or OFF. From the “Wipers” menu, select
“Drip wipe”. Use the OK
*1to turn this
feature ON or OFF.
Remote start (if so equipped):
The “Remote start” feature allows user to turn
the remote engine start on or off. When turned
on, the engine can be restarted remotely. For
additional information, refer to “Remote engine
start” (P.3-22) .
JVI1670X
1. Oil and Filter
2. Tire
3. Other
Maintenance
The maintenance mode allows you to set alerts
for the reminding of maintenance intervals. To
change an item:
Select “Maintenance” using the
switch*2
and press OK*1.
Oil and Filter:
This indicator appears when the customer set
distance comes for changing the engine oil and
filter. You can set or reset the distance for
Instruments and controls2-23

2-24Instruments and controls
checking or replacing these items. For sched-
uled maintenance items and intervals, refer to
the “9. Maintenance and schedules” section.
Tire:
This indicator appears when the customer set
distance comes for replacing tires. You can set
or reset the distance for replacing tires.
WARNING
The tire replacement indicator is not a
substitute for regular tire checks, in-
cluding tire pressure checks. See
“Changing wheels and tires”(P.8-37) .
Many factors including tire inflation,
alignment, driving habits and road con-
ditions affect tire wear and when tires
should be replaced. Setting the tire
replacement indicator for a certain
driving distance does not mean your
tires will last that long. Use the tire
replacement indicator as a guide only
and always perform regular tire checks.
Failure to perform regular tire checks,
including tire pressure checks could
result in tire failure. Serious vehicle
damage could occur and may lead to a
collision, which could result in serious
personal injury or death.Other:
This indicator appears when the customer set
distance comes for checking or replacing
maintenance items other than the engine oil, oil
filter and tires. Other maintenance items can
include such things as air filter or tire rotation.
You can set or reset the distance for checking or
replacing the items.
Alarm (if so equipped)
This setting allows the customer to set alarms.
Select “Alarm” using the
button*2and
press OK button
*1.
Timer Alert (if so equipped):
This setting allows the customer to set an alert
to notify the driver that the set time has been
reached.
1. Use the
button*2to select “Timer
Alert”.
2. Press the OK button
*1.
3. To change the timer amount, use the
button*2and the OK button*1to save
the selected time amount.
Navigation (if so equipped):
This setting allows the customer to enable/
disable the alert for navigation in the vehicle
information display.1. Use the
button*2to select “Naviga-
tion”.
2. Press the OK button
*1to turn ON/OFF
the alert.
Phone (if so equipped):
This setting allows the customer to enable/
disable the alert for an incoming call in the
vehicle information display.
1. Use the
button*2to select “Phone”.
2. Press the OK button
*1to turn ON/OFF
the alert.
Mail (if so equipped):
This setting allows the customer to enable/
disable the alert for navigation in the vehicle
information display.
1. Use the
button*2to select “Mail”.
2. Press the OK button
*1to turn ON/OFF
the alert.

Tire Pressures
The settings in the “Tire pressures” menu are all
related to the Tire Pressure Monitoring System
(TPMS) . (See “Tire Pressure Monitoring System
(TPMS)” (P.5-5) , “Tire Pressure Monitoring
System (TPMS)” (P.6-3) , “Tire Pressure Mon-
itoring System (TPMS)” (P.8-29) .)
Tire Pressure Unit:
The unit for tire pressure that displays in the
vehicle information display can be changed to:
.psi
.kPa
.bar
.Kgf/cm
2
Use thebutton*2and the OK button*1
to select and change the unit.
If necessary, refer to the following table to
convert between units.
JVI0938X
Unit
The units that are shown in the vehicle informa-
tion display can be changed:
.Mileage
.Tire pressures
.Temperature
Use the
button*2, and the OK button*1
to select and change the units of the vehicle
information display.
Mileage:
The unit for the mileage that displays in the
vehicle information display can be changed to:.km, l/100km
.km, km/l
.miles, MPG
Use the
button*2and the OK button*1
to select and change the unit.
Tire pressures:
See “Tire Pressures” (P.2-25) .
Temperature:
The temperature that displays in the vehicle
information display can be changed from:
.8C (Celsius)
.8F (Fahrenheit)
Use the
button*2to toggle choices.
Instruments and controls2-25