2017 MAZDA MODEL MX-5 RF light

4–14 3
When Driving
Tyre Pressure Monitoring System
Tyre Pressure Monitoring System
Initialization
In the following cases, system
initialization must be performed so that the
system operates normally.
 


 A tyre pressure is adjusted.



 Tyre rotation is performed.



 A tyre or wheel is replaced.



 The battery is replaced or completely
drained.
 


 The tyre pressure monitoring system
warning light is illuminated.
Initialization method
1. Park the car in a safe place and ¿ rmly
apply the parking brake.
2. Let the tyres cool, then adjust the tyre
pressure of all four (4) tyres to the
speci¿ ed pressure indicated on the tyre
pressure label located on the driver's
door frame (door open).
Refer to Tyres on page 9-8 .
3. Switch the ignition ON.
4. Press and hold the tyre pressure
monitoring system set switch and
verify that the tyre pressure monitoring
system warning light in the instrument
clusterÀ ashes twice and a beep sound
is heard once.
CAUTION
If the system initialization is performed
without adjusting the tyre pressure, the
system cannot detect the normal tyre
pressure and it may not illuminate the
tyre pressure monitoring system warning
light even if a tyre pressure is low, or
it may illuminate the light even if the
pressures are normal.
Adjust the tyre pressure on all four
tyres and initialize the system when
the warning light is turned on. If the
warning light turns on for a reason other
than a À at tyre, the tyre pressure of all
four tyres may have decreased naturally.
The system initialization will not be
performed if the switch is pressed while
the vehicle is being driven.
/:A(.'',A'FKVKQPKPFD

4–14 4
When Driving
Tyre Pressure Monitoring System
*Some models.
Tyre Pressure Monitoring System (Vehicle with Run-À at
Ty r e s )
*
The Tyre Pressure Monitoring System (TPMS) monitors the pressure for each tyre.
If tyre pressure is too low in one or more tyres, the system will inform the driver via the
warning light in the instrument cluster and by the warning beep sound.
Refer to Warning Indication/Warning Lights on page 4-42 .
Refer to Tyre InÀ ation Pressure Warning Beep on page 7-53 .
The tyre pressure sensors installed on each wheel send tyre pressure data by radio signal to
the receiver unit in the vehicle.
Tyre pressure sensors
NOTE
When the ambient temperature is low due to seasonal changes, tyre temperatures are also
lower. When the tyre temperature decreases, the air pressure decreases as well. The TPMS
warning light may illuminate more frequently. Visually inspect the tyres daily before
driving, and check tyre pressures monthly with a tyre pressure gauge. When checking tyre
pressures, use of a digital tyre pressure gauge is recommended.
TPMS does not alleviate your need to check the pressure and condition of all four tyres
regularly.
/:A(.'',A'FKVKQPKPFD

4–14 6
When Driving
Tyre Pressure Monitoring System
System Error Activation
When the TPMS warning light À ashes,
there may be a system malfunction.
Consult an Authorised Mazda Dealer.
A system error activation may occur in the
following cases:
 


 When there is equipment or a device
near the vehicle using the same radio
frequency as that of the tyre pressure
sensors.
 


 When a metallic device such as a non-
genuine navigation system is equipped
near the centre of the instrument panel,
which may block radio signals from the
tyre pressure sensor to the receiver unit.
 


 When using the following devices in the
vehicle that may cause radio interference
with the receiver unit.
 

 
 A digital device such as a personal
computer.
 

 
 A current converter device such as a
DC-AC converter.
 


 When excess snow or ice adheres to the
vehicle, especially around the wheels.
 


 When the tyre pressure sensor batteries
are exhausted.
 


 When using a wheel with no tyre
pressure sensor installed.
 


 When using tyres with steel wire
reinforcement in the side walls.
 


 When using tyre chains.
Tyres and Wheels
CAUTION
When inspecting or adjusting the tyre air
pressures, do not apply excessive force
to the stem part of the wheel unit. The
stem part could be damaged.
Changing tyres and wheels
The following procedure allows the TPMS
to recognise a tyre pressure sensor's
unique ID signal code whenever tyres or
wheels are changed, such as changing to
and from winter tyres.
NOTE
Each tyre pressure sensor has a unique
ID signal code. The signal code must be
registered with the TPMS before it can
work. The easiest way to do it is to have
an Authorised Mazda Dealer change
your tyre and complete ID signal code
registration.
When having tyres changed at an
Authorised Mazda Dealer
When an Authorised Mazda Dealer
changes your vehicle's tyres, they will
complete the tyre pressure sensor ID signal
code registration.
When changing tyres yourself
If you or someone else changes tyres, you
or someone else can also undertake the
steps for the TPMS to complete the ID
signal code registration.
/:A(.'',A'FKVKQPKPFD

4–147
When Driving
Tyre Pressure Monitoring System
1. After tyres have been changed, switch
the ignition ON, then back to ACC or
OFF.
2. Wait for about 15 minutes.
3. After about 15 minutes, drive the
vehicle at a speed of at least 25 km/h
(16 mph) for 10 minutes and the tyre
pressure sensor ID signal code will be
registered automatically.
NOTE
If the vehicle is driven within about
15 minutes of changing tyres, the tyre
pressure monitoring system warning
light will À ash because the sensor
ID signal code would not have been
registered. If this happens, park the
vehicle for about 15 minutes, after
which the sensor ID signal code will
register upon driving the vehicle for 10
minutes.
Replacing tyres and wheels
CAUTION
  When replacing/repairing the tyres or
wheels or both, have the work done
by an Authorised Mazda Dealer, or
the tyre pressure sensors may be
damaged.
  The wheels equipped on your Mazda
are specially designed for installation
of the tyre pressure sensors. Do not
use non-genuine wheels, otherwise it
may not be possible to install the tyre
pressure sensors. Be sure to have the tyre pressure sensors
installed whenever tyres or wheels are
replaced.
When having a tyre or wheel or both
replaced, the following types of tyre
pressure sensor installations are possible.
 


 The tyre pressure sensor is removed
from the old wheel and installed to the
new one.
 


 The same tyre pressure sensor is used
with the same wheel. Only the tyre is
replaced.
 


 A new tyre pressure sensor is installed to
a new wheel.
NOTE
  The tyre pressure sensor ID signal
code must be registered when a new
tyre pressure sensor is purchased. For
purchase of a tyre pressure sensor
and registration of the tyre pressure
sensor ID signal code, consult an
Authorised Mazda Dealer.
  When reinstalling a previously
removed tyre pressure sensor to a
wheel, replace the grommet (seal
between valve body/sensor and
wheel) for the tyre pressure sensor.
/:A(.'',A'FKVKQPKPFD

5–1*Some models.5–1
5Interior Features
Use of various features for ride comfort, including air-conditioning and
audio system.
Air-Conditioning System ................................................................... 5-2
Operating Tips ............................................................................... 5-2
Vent Operation .............................................................................. 5-3
Manual Type ................................................................................. 5-5
Fully Automatic Type .................................................................. 5-10
Audio System .................................................................................... 5-14
Aerial ........................................................................................... 5-14
Operating Tips for Audio System ............................................... 5-14
Audio Set [Type A (non-touchscreen)] ....................................... 5-28
Audio Set [Type B/Type C (touchscreen)] .................................. 5-44
Audio Control Switch Operation
* ............................................... 5-69
AUX/USB mode ......................................................................... 5-71
Bluetooth
® ......................................................................................... 5-90
Bluetooth®* .................................................................................. 5-90
Bluetooth® Hands-Free * .............................................................. 5-99
Bluetooth® Audio * ..................................................................... 5-108
Troubleshooting ........................................................................ 5-119
Interior Equipment ........................................................................ 5-123
Sunvisors ................................................................................... 5-123
Interior Lights ........................................................................... 5-123
Accessory Socket ...................................................................... 5-125
Cup Holder ................................................................................ 5-126
Storage Compartments .............................................................. 5-131
Removable Ashtray
* .................................................................. 5-133
Windblocker .............................................................................. 5-133
/:A(.'',A'FKVKQPKPFD

5–2
Interior Features
Air-Conditioning System
O p e r a t i n g T i p s
 












 Operate the air-conditioning system with
the engine running.
 


 To prevent the battery from being
discharged, do not leave the fan control
dial on for a long period of time with the
ignition switched ON when the engine is
not running.
 


(With i-stop)
 The airÀ ow amount may decrease
slightly while the i-stop function is
operating.
 


 Clear all obstructions such as leaves,
snow and ice from the bonnet and the
air inlet in the cowl grille to improve the
system ef¿ ciency.




 Use the air-conditioning system to defog
the windows and dehumidify the air.
 


 The recirculate mode should be used
when driving through tunnels or while in
a traf¿ c jam, or when you would like to
shut off outside air for quick cooling of
the interior.
 


 Use the outside air position for
ventilation or windscreen defrosting.
 


 If the vehicle has been parked in direct
sunlight during hot weather, open the
windows to let warm air escape, then
run the air-conditioning system.
 


 Run the air conditioner about 10 minutes
at least once a month to keep internal
parts lubricated.
 


 Have the air conditioner checked before
the weather gets hot. Lack of refrigerant
may make the air conditioner less
ef¿ cient.

 The refrigerant speci¿ cations are
indicated on a label attached to the
inside of the engine compartment. Check
the label before re¿ lling the refrigerant.
If the wrong type of refrigerant is used,
it could result in a serious malfunction
of the air conditioner.
  For details, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Label
/:A(.'',A'FKVKQPKPFD

5–6
Interior Features
Air-Conditioning System
Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and anticlockwise for
cold.
NOTE
(Type A)
When the mode is set to
, or a
position in between them with the fan
control dial in a position other than 0
and the temperature control dial in the
maximum cold position, the air intake
selector switches to the recirculated air
position and the A/C turns on
automatically.
If A/C is not desired, press the A/C
switch to turn it off.
Fan control dial
This dial allows variable fan speeds.
The fan has seven speeds.
Mode selector dial
Turn the mode selector dial to select
airÀ ow mode (page 5-4 ).
NOTE

 The mode selector dial can be set at
the intermediate positions (
)
between each mode. Set the dial to
an intermediate position if you want
to split the airÀ ow between the two
modes.
  For example, when the mode selector
dial is at the
position between the
and positions, airÀ ow from the
À oor vent is less than that of the
position.
A/C switch
Press the A/C switch to turn the air
conditioner on. The indicator light on the
switch will illuminate when the fan control
dial is in any position except OFF.
Press the switch once again to turn the air
conditioner off.
NOTE
The air conditioner may not function
when the outside temperature
approaches 0 °C (32 °F).
Air intake selector
This switch controls the source of air
entering the vehicle.
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (indicator light
illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traf¿ c (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (indicator light
turned off)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windscreen defrosting.
/:A(.'',A'FKVKQPKPFD

5–7
Interior Features
Air-Conditioning System
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.
Rear window defogger switch
Press the rear window defogger switch to
defrost the rear window.
Refer to Rear Window Defogger on page
4-77 .
Heating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside
air position (indicator light turns off).
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidi¿ ed heating is desired, turn
on the air conditioner.
NOTE
  If the windscreen fogs up easily, set
the mode selector dial to the
position.  If cooler air is desired at face level,
set the mode selector dial at the
position and adjust the temperature
control dial to maintain maximum
comfort.
  The air to the À oor is warmer than
air to the face (except when the
temperature control dial is set at the
extreme hot or cold position).
Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.
CAUTION
If the air conditioner is used while
driving up long hills or in heavy traf¿ c,
monitor the engine coolant temperature
warning light to see if it is illuminated or
À ashing (page 4-42 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or À ashing, turn the air-
conditioning off (page 7-24 ).
/:A(.'',A'FKVKQPKPFD