2017 MAZDA MODEL MX-5 RF oil level

6–5
Maintenance and Care
Scheduled Maintenance
*5 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil ¿ lter at
every 10,000 km (6,250 miles) or shorter.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*6 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*7 Inspect the battery electrolyte level, speci¿ c gravity and outer appearance. The sealed battery only requires an
outer appearance inspection.
*8 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, replace the brake À uid annually.
*9 If this component has been submerged in water, the oil should be replaced.
*10 Tyre rotation is recommended every 10,000 km (6,250 miles).
*11 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*12 Check the tyre repair À uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair À uid bottle with new one before the expiration date.
Except Europe
I s r a e l
Maintenance Interval Number of months or kilometres, whichever comes ¿ rst
Months 12 24 36 48 60 72 84 96 108 120 132 144
×1000 km 15 30 45 60 75 90 105 120 135 150 165 180
Spark plugs Replace every 120,000 km or 6 years.
Fuel ¿ lter Replace every 135,000 km.
Evaporative system (if installed) I I I
Fuel lines and hoses
I I
I
I I
I
Drive belts
*1 I I I I I I I I I I I I
Engine oil & oil ¿ lter *2 R R R R R R R R R R R R
Air ¿ lter *3 C C C R C C C R C C C R
Cooling system I I I I I I
Engine coolant
*4 Replace at ¿ rst 195,000 km or 10 years; after that, every
90,000 km or 5 years.
Battery
*5 I I I I I I I I I I I I
Brake lines, hoses and connections I I I I I I I I I I I I
Brake À uid
*6 I R I R I R I R I R I R
Parking brake I I I I I I I I I I I I
Power brake unit (Brake booster) and hoses I I I I I I I I I I I I
Disc brakes I I I I I I I I I I I I
/:A(.'',A'FKVKQPKPFD

6–6
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometres, whichever comes ¿ rst
Months 12 24 36 48 60 72 84 96 108 120 132 144
×1000 km 15 30 45 60 75 90 105 120 135 150 165 180
Steering operation and linkages I I I I I I
Manual transmission oil R R
Rear differential oil
*7
Front and rear suspension, ball joints and wheel
bearing axial play I I I I I I I I I I I I
Driveshaft dust boots I I I I
Exhaust system and heat shields Inspect every 75,000 km.
Bolts and nuts on chassis and body T T T T T T T T T T T T
Body condition (for rust, corrosion and
perforation) Inspect annually.
Tyres (including spare tyre) (with inÀ ation
pressure adjustment)
*8 I I I I I I I I I I I I
Emergency À at tyre repair kit (if installed)
*9 Inspect annually.
Chart symbols:
I : Inspect: Inspect and clean, repair, adjust, ¿ ll up, or replace if necessary.
R : Replace
C : Clean
T : Tighten
D : Drain
Remarks:
*1 Also inspect the air conditioner drive belts, if installed.
If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every
10,000 km or shorter.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation
c) Driving for long period in cold temperatures or driving regularly at short distance only
d) Driving in extremely hot conditions
e) Driving in mountainous conditions continually
*2 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil ¿ lter at
every 10,000 km or shorter.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*3 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air ¿ lter more often
than the recommended intervals.
*4 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*5 Inspect the battery electrolyte level, speci¿ c gravity and outer appearance. The sealed battery only requires an
outer appearance inspection.
/:A(.'',A'FKVKQPKPFD

6–9
Maintenance and Care
Scheduled Maintenance
*3 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil ¿ lter
more often than the recommended intervals.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*4 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*5 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air ¿ lter more often
than the recommended intervals.
*6 Inspect the battery electrolyte level, speci¿ c gravity and outer appearance. If the vehicle is operated in
extremely hot and cold areas, inspect the battery electrolyte level, speci¿ c gravity and appearance every 10,000
km (6,250 miles) or 6 months. The sealed battery only requires an outer appearance inspection.
*7 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, replace the brake À uid annually.
*8 If this component has been submerged in water, the oil should be replaced.
*9 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*10 Check the tyre repair À uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair À uid bottle with new one before the expiration date.
/:A(.'',A'FKVKQPKPFD

6–12
Maintenance and Care
Owner Maintenance
Owner Maintenance Precautions
R o u t i n e S e r v i c e
We highly recommend that these items be inspected daily, or at least every week.
 


 Engine Oil Level (page 6-20 )



 Engine Coolant Level (page 6-20 )



 Brake and clutch Fluid Level (page 6-22 )



 Washer Fluid Level (page 6-23 )



 Battery Maintenance (page 6-30 )



 Tyre InÀ ation Pressure (page 6-34 )
Improper or incomplete service may result in problems. This section gives instructions only
for items that are easy to perform.
As explained in the Introduction (page 6-2 ), several procedures can be done only by a
quali¿ ed service technician with special tools.
Improper do-it yourself maintenance during the warranty period may affect warranty
coverage. For details, read the separate Mazda Warranty statement provided with the
vehicle. If you are unsure about any servicing or maintenance procedure, have it done by an
expert repairer, we recommend an Authorised Mazda Repairer.
There are strict environmental laws regarding the disposal of waste oil and À uids. Please
dispose of your waste properly and with due regard to the environment.
We recommend that you entrust the oil and À uid changes of your vehicle to an Authorised
Mazda Repairer.
/:A(.'',A'FKVKQPKPFD

6–20
Maintenance and Care
Owner Maintenance
Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait at least 5 minutes
for the oil to return to the sump.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
MIN MAX
OK
5. Pull it out again and examine the level.
The level is normal if it is between the
MIN and MAX marks.
If it is near or below MIN, add enough
oil to bring the level to MAX.
CAUTION
Do not over¿ ll the engine oil. This may
cause engine damage.
6. Make sure the O-ring on the dipstick is
positioned properly before reinserting
the dipstick.
7. Reinsert the dipstick fully.
Engine Coolant
Inspecting Coolant Level
WARNING
Do not use a match or live À ame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS
HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running inde¿ nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.
Do not remove either
cooling system cap when the engine
and radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.
/:A(.'',A'FKVKQPKPFD

7–33
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Engine Oil Warning
Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in
extensive engine damage.
If the light illuminates or the warning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way on level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the sump.
3. Inspect the engine oil level 6-20 . If it's low, add the appropriate amount of engine
oil while being careful not to over¿ ll.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.
If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an expert repairer, we
recommend an Authorised Mazda Repairer.
(Red)
High Engine Coolant
Temperature Warning
Indication/Warning
Light
The light À ashes when the engine coolant temperature is extremely high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can ¿ nd a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place
immediately and stop the engine.
Refer to Overheating 7-24 .
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.
/:A(.'',A'FKVKQPKPFD

9–6
Speci¿ cations
Speci¿ cations
Capacities
(Approximate Quantities)
Item Capacity
Engine
oil With oil ¿ lter replacement 4.3 L (4.5 US qt, 3.8 Imp qt)
Without oil ¿ lter replacement 4.1 L (4.3 US qt, 3.6 Imp qt)
Coolant SKYACTIV-G 1.5 Left-hand drive model 5.6 L (5.9 US qt, 4.9 Imp qt)
Right-hand drive model 5.8 L (6.1 US qt, 5.1 Imp qt)
SKYACTIV-G 2.0 Manual
transmission Left-hand drive model 6.0 L (6.3 US qt, 5.3 Imp qt)
Right-hand drive model 6.2 L (6.6 US qt, 5.5 Imp qt)
Automatic
transmission Saudi Arabia 6.2 L (6.6 US qt, 5.5 Imp qt)
Right-hand drive model 6.0 L (6.3 US qt, 5.3 Imp qt)
Except above 5.9 L (6.2 US qt, 5.2 Imp qt)
Manual transmission oil 2.0 L (2.1 US qt, 1.8 Imp qt)
Automatic transmission À uid 7.2 L (7.6 US qt, 6.3 Imp qt)
Rear differential oil 0.6 L (0.6 US qt, 0.5 Imp qt)
Fuel tank 45.0 L (11.9 US gal, 9.90 Imp gal)
Check oil and À uid levels with dipsticks or reservoir gauges.
Dimensions
Item Vehicle speci¿ cation
Soft top model Retractable fastback
model
Overall length 3,915 mm (154.1 in) 3,915 mm (154.1 in)
Overall width 1,735 mm (68.3 in) 1,735 mm (68.3 in)
Overall height 16 inch wheel vehicle 1,225 mm (48.2 in) 1,230 mm (48.4 in)
17 inch wheel vehicle 1,230 mm (48.4 in) 1,235 mm (48.6 in)
Front tread 1,495 mm (58.9 in) 1,495 mm (58.9 in)
Rear tread 1,505 mm (59.3 in) 1,505 mm (59.3 in)
Wheelbase 2,310 mm (90.9 in) 2,310 mm (90.9 in)
/:A(.'',A'FKVKQPKPFD

10–4
Index
Engine
Bonnet release ............................... 6-14
Coolant .......................................... 6-20
Engine compartment overview ..... 6-16
Exhaust gas.................................... 3-26
Oil .................................................. 6-17
Starting ............................................ 4-5
Engine Coolant Temperature
Gauge ......................................... 4-27, 4-36
Essential Information ............................ 6-2
Exhaust Gas ........................................ 3-26
Exterior Care ....................................... 6-53
Aluminium wheel maintenance..... 6-58
Bright-metal maintenance ............. 6-57
Cavity protection ........................... 6-57
Convertible Top (Retractable Fastback)
Maintenance .................................. 6-61
Convertible Top (Soft Top)
Maintenance .................................. 6-58
Maintaining the ¿ nish ................... 6-55
Paint damage touch-up .................. 6-57
Plastic part maintenance ................ 6-63
Undercoating ................................. 6-57
F
Flasher
Hazard warning ............................. 4-79
Headlights ..................................... 4-63
Flat Tyre ................................................ 7-3
Mounting the tyre .......................... 7-17
Removing a tyre ............................ 7-14
Floor Mat ............................................ 3-61
Fluid
Brake/Clutch ................................. 6-22
Washer ........................................... 6-23
Fluids
Classi¿ cation ................................... 9-5
Foot Brake ........................................... 4-81
Forward Sensing Camera (FSC) ....... 4-129 Fuel
Filler À ap and cap .......................... 3-27
Gauge ................................... 4-27, 4-36
Requirements................................. 3-24
Tank capacity .................................. 9-6
Fuel Consumption Display ................. 4-94
Fuel Economy Monitor ....................... 4-93
Control status display .................... 4-94
Effectiveness display ..................... 4-96
Ending screen display ................... 4-96
Fuel consumption display ............. 4-94
Fuel-Filler Flap
When fuel-¿ ller À ap cannot be
opened ........................................... 7-26
Fuses ................................................... 6-47
Panel description ........................... 6-50
Replacement .................................. 6-47
G
Gauges ................................................. 4-24
H
Hazard Warning Flasher ...................... 4-79
Hazardous Driving .............................. 3-60
Head Restraint ....................................... 2-8
Headlight Washer ................................ 4-77
Headlights
Coming home light ........................ 4-68
Control........................................... 4-63
Flashing ......................................... 4-68
High-low beam .............................. 4-68
Leaving home light ....................... 4-69
Levelling ....................................... 4-70
Running lights ............................... 4-70
Washer ........................................... 4-77
High Beam Control System (HBC) ... 4-103
High Beam Control System (HBC)
indicator light (green) .................. 4-105
Hill Launch Assist (HLA) ................... 4-84
Horn .................................................... 4-79
/:A(.'',A'FKVKQPKPFD