2017 MAZDA MODEL MX-5 RF light

6–30
Maintenance and Care
Owner Maintenance
Battery Maintenance
To get the best service from a battery:
 


 Keep it securely mounted.



 Keep the top clean and dry.



 Keep terminals and connections clean,
tight, and coated with petroleum jelly or
terminal grease.
 


 Rinse off spilled electrolyte immediately
with a solution of water and baking
soda.
 


 If the vehicle will not be used for an
extended time, disconnect the battery
leads and charge the battery every six
weeks.
Inspecting Electrolyte Level
A low level of electrolyte À uid will cause
the battery to discharge quickly.
Upper level
Lower level
Inspect the electrolyte level at least once
a week. If it is low, remove the caps and
add enough distilled water to bring the
level between the upper and lower level
(illustration).
Do not over¿ ll.
Examine the speci¿ c gravity of the
electrolyte with a hydrometer, especially
during cold weather. If it is low, recharge
the battery.
Battery Recharging
NOTE
  Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.
  To disconnect the battery, remove the
negative lead ¿ rst. Install it last when
connecting the battery.
  Be sure to remove the caps before
recharging the battery.
 (With i-stop system) Do not quick-charge the battery.




 If the battery quickly discharges
because, for example, the lights were
left on too long with the engine off,
slow-charge it as required by battery
size and charger capacity.
 


 If the battery gradually discharges
because of high electric load while the
vehicle is being used, recharge it as
required by battery size and charger
capacity.
Battery Replacement
Contact an Authorised Mazda Repairer for
a battery replacement purchase.
/:A(.'',A'FKVKQPKPFD

6–31
Maintenance and Care
Owner Maintenance
Key Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not À ash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
  Make sure the battery is installed
correctly. Battery leakage could
occur if it is not installed correctly.
  When replacing the battery, be
careful not to touch any of the
internal circuitry and electrical
terminals, bend the electrical
terminals, or get dirt in the
transmitter as the transmitter could
be damaged.
  There is the danger of explosion if
the battery is not correctly replaced.
  Dispose of used batteries according
to the following instructions.
 


 Insulate the plus and minus
terminals of the battery using
cellophane or equivalent tape.
 


 Never disassemble.



 Never throw the battery into ¿ re or
water.
 


 Never deform or crush. 

 Replace only with the same type
battery (CR2025 or equivalent).
The following conditions indicate that the
battery power is low:
 


 The KEY indicator light (green) À ashes
in the instrument cluster for about 30
seconds after the engine is turned off.
 


 The system does not operate and
the operation indicator light on the
transmitter does not À ash when the
buttons are pressed.
 


 The system's operational range is
reduced.
Replacing the battery at an Authorised
Mazda Repairer is recommended to
prevent damage to the key. If replacing the
battery by yourself, follow the instruction.
Replacing the key battery
1. Press the knob and pull out the
auxiliary key.
Knob
/:A(.'',A'FKVKQPKPFD

6–32
Maintenance and Care
Owner Maintenance
2. Twist a tape-wrapped À athead
screwdriver in the direction of the
arrow and open the cover slightly.
Cover
3. Insert the tape-wrapped À athead
screwdriver into the gap and slide it in
the direction of the arrow.
Cover
Gap
4. Twist the À athead screwdriver in the
direction of the arrow and remove the
cover.
Cover
5. Remove the battery cap, then remove
the battery.
6. Insert a new battery with the positive
pole facing up, and then cover the
battery with the battery cap.
7. Close the cover.
8. Reinsert the auxiliary key.
/:A(.'',A'FKVKQPKPFD

6–36
Maintenance and Care
Owner Maintenance
*Some models.
If a tyre wears evenly, a wear indicator
will appear as a solid band across the
tread.
Replace the tyre when this happens.
New treadTread wear indicator
Worn tread
You should replace the tyre before the
band crosses the entire tread.
(With tyre pressure monitoring system)
After adjusting the tyre pressure,
initialization of the tyre pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tyre Pressure Monitoring System
Initialization on page 4-143 .
Replacing a Wheel
WARNING
Always use wheels of the correct size
on your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident.
CAUTION
A wrong-sized wheel may adversely
affect:
 
 Tyre ¿ t 
 Wheel and bearing life 
 Ground clearance 
 Snow-chain clearance 
 Speedometer calibration 
 Headlight aim 
 Bumper height 
 Tyre Pressure Monitoring System *
NOTE

 When replacing a wheel, make
sure the new one is the same as the
original factory wheel in diameter,
rim width, and offset (inset/outset).
  For details, contact an expert
repairer, we recommend an
Authorised Mazda Repairer.
Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and À at spots.
/:A(.'',A'FKVKQPKPFD

6–38
Maintenance and Care
Owner Maintenance
Light Bulbs
6
15
1316
15234
1011141012789
/:A(.'',A'FKVKQPKPFD

6–39
Maintenance and Care
Owner Maintenance
*Some models.
Headlights (Low beam)
Headlights (High beam)
Running lights
Position lights
Front direction indicator lights
Side direction indicator lights
Brake lights
Rear direction indicator lights
Tail lights
Reverse lights
Rear fog light (Left-hand drive model) *
Rear fog light (Right-hand drive model) *
High-mount brake light
Number plate lights
Overhead light
Boot light
/:A(.'',A'FKVKQPKPFD

6–40
Maintenance and Care
Owner Maintenance
CAUTION
When removing the lens or lamp unit
using a À athead screwdriver, make
sure that the À athead screwdriver does
not contact the interior terminal. If
theÀ athead screwdriver contacts the
terminal, a short circuit may occur.
NOTE
  To replace the bulb, contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Replacing Exterior Light Bulbs
Headlights, Running lights (LED type),
Position lights, High-mount brake light,
Brake lights, Tail lights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with
the unit. We recommend an Authorised
Mazda Repairer when the replacement is
necessary.
Running lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the centre of each plastic retainer
and remove the retainers.
Removal
Installation
3. Turn the screw anticlockwise and
remove it, and then partially peel back
the mudguard.
4. Turn the socket and bulb assembly
anticlockwise and remove it.
/:A(.'',A'FKVKQPKPFD

6–41
Maintenance and Care
Owner Maintenance
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order
of the removal procedure.
Front direction indicator lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the centre of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Removal
Installation
4. Disconnect the connector from the unit
by pressing the tab on the connector
with your ¿ nger and pulling the
connector rearward.
5. Turn the socket and bulb assembly
anticlockwise and remove it.
6. Disconnect the bulb from the socket.
7. Install the new bulb in the reverse order
of the removal procedure.
Side direction indicator lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
/:A(.'',A'FKVKQPKPFD