2017 MAZDA MODEL CX-5 warning light

SignalWarning
(Amber)
KEY Warning Indi-
cation
*
“Keyless System malfunction” is displayed
This message is displayed if the advanced keyless entry & push button start system has a
problem.
Contact an expert repairer, we recommend an Authorised Mazda Repairer.
CAUTION
If the message is indicated, or the push button start indicator light (amber) flashes, the en‐
gine may not start. If the engine cannot be st arted, try starting it using the emergency oper‐
ation for starting the engine, an d have the vehicle inspected at an expert repairer, we rec‐
ommend an Authorised Mazda Repairer as soon as possible.
Refer to Emergency Operation for St arting the Engine on page 4-10.
“Set Power to OFF” is displayed
This message is displayed when the driver's door is opened with out switching the ignition
off.
“Key not found” is displayed
This message is displayed when a ny of the following operations is performed with the key
out of the operational range or placed in areas inside the cabi n where it is difficult for the
key to be detected.
•The push button start is pressed with the ignition switched off•The ignition is switched on•All doors are closed without switching the ignition off
(Red)
(Turns on)
KEY Warning
Light
*
If any malfunction o ccurs in the keyless entry system, it illum inates continuously.
CAUTION
If the key warning indicator light illuminates or the push button start indicator light (am‐
ber) flashes, the engine may not start. If the engine cannot be started, try starting it using
the emergency operation for starting the engine, and have the vehicle inspected at an ex‐
pert repairer, we recommend an Authoris ed Mazda Repairer as soon as possible.
Refer to Emergency Operation for Starting the Engine on page 4- 10.
Security Indicator
Light If the engine does not start with the correct key, and the secu
rity indicator light remains
illuminated or flashing, try the following:
Make sure the key is within the operational range for signal transmission. Switch the igni-
tion off, and then restart the engine. If the engine does not s tart after 3 or more tries, con-
tact an expert repairer, we reco mmend an Authorised Mazda Repai rer.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-51
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning
(Amber)
i-stop Warning
Light
*
When the light is turned on
A problem in the system may be i ndicated under the following conditions. Have your ve-
hicle inspected at an expert repairer, we recommend an Authoris ed Mazda Repairer.
•The light does not turn on when the ignition is switched ON.•The light continues to remain on even though the i-stop OFF swi tch has been pressed
while the engine is running.
When the light is flashing
The light continues to flash if the system has a malfunction. H ave your vehicle inspected
at an expert repairer, we recommend an Authorised Mazda Repaire r.
i-ELOOP Warning
Indication*
The Warning indication turns on if there is any malfunction in the i-ELOOP system. Con-
sult an expert repairer, we reco mmend an Authorised Mazda Repai rer.
(Amber)
High Beam Control System (HBC)
Wa r n i n g L i g h t
*
The light remains turned on if th ere is a problem with the system. Have your vehicle in-
spected at an expert repairer, we recommend an Authorised Mazda Repairer.
NOTE
If the windscreen area in front of the Forward Sensing Camera (FSC) is fogged or ob-
structed, the light turns on temporarily. If the light remains turned on, there may be a
problem with the system.
(Amber)
Adaptive LED
Headlights (ALH)
Wa r n i n g L i g h t
*
The light remains turned on if th ere is a problem with the system. Have your vehicle in-
spected at an expert repairer, we recommend an Authorised Mazda Repairer.
NOTE
If the windscreen area in front of the Forward Sensing Camera (FSC) is fogged or ob-
structed, the light turns on temporarily. If the light remains turned on, there may be a
problem with the system.
Blind Spot Monitor-
ing (BSM) Warning
Indication
*
This light illuminates if there i s a malfunction in the Blind Spot Monitoring (BSM). Have
your vehicle inspected by an expe rt repairer, we recommend an Authorised Mazda Re-
pairer.
NOTE
If the vehicle is driven on a road with less traffic and few vehicles that the radar sensors
can detect, the system may pause. However , it does not indicate a malfunction.
Blind Spot Monitor-
ing (BSM) OFF In-
dicator Light
*
A problem in the system may be i ndicated under the following conditions.
Have your vehicle inspected at an expert repairer, we recommend an Authorised Mazda
Repairer.
•The light does not turn on when the ignition is switched ON.•The light remains on even when the Blind Spot Monitoring (BSM) system can be operat-
ed.
•The light turns on while driving the vehicle.
NOTE
If the vehicle is driven on a road with less traffic and few vehicles that the radar sensors
can detect, the system may pause (The Bli nd Spot Monitoring (BSM) OFF indicator light
in the instrument cluster illuminates). However, it does not indicate a malfunction.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-52*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning
(Amber)
Driver Attention
Alert (DAA) Warn-
ing Indication
*
The message is displayed when the system has a malfunction. Have your vehicle inspect-
ed at an expert repairer, we r ecommend an Authorised Mazda Repa irer.
(Amber)
Mazda Radar Cruise
Control (MRCC)
Warning Indication
*
The message is displayed when the system has a malfunction. Have your vehicle inspect-
ed at an expert repairer, we r ecommend an Authorised Mazda Repa irer.
(Amber)
Mazda Radar Cruise
Control with Stop &
Go function (MRCC with Stop & Go
function) Warning
Indication
*
The message is displayed when the system has a malfunction. Have your vehicle inspect-
ed at an expert repairer, we r ecommend an Authorised Mazda Repa irer.
(Amber)
Lane-keep Assist System (LAS) & Lane Departure
Wa r n i n g S y s t e m
(LDWS) Warning
Indication
*
The message is displayed when the system has a malfunction. Have your vehicle inspect-
ed at an expert repairer, we r ecommend an Authorised Mazda Repa irer.
The system does not operate when the warning message is displayed.
CAUTION
Always use tyres for all wheels that are of the
specified size, and the same manufacture,
brand, and tread pattern. In addition, do not use tyres with significantly different wear
patterns on the same vehicle. If such improper tyres are used, the system may not oper‐
ate normally.
 When an emergency spare tyre is used, the system may not operate normally.
LED Headlight
Wa r n i n g L i g h t This light illuminates if there i
s a malfunction in the LED hea dlight. Have your vehicle
inspected by an expert repairer , we recommend an Authorised Maz da Repairer.
▼Taking Action
Take the appropriate action and verify that the warning light t
urns off.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-53
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning Action to be taken
(Amber)
Smart Brake Support/
Smart City Brake Sup-
port (SBS/SCBS)
Warning Light
*
The light turns on if the windscreen or the
radar sensor are dirty, or there is a malfunc-
tion in the system. Verify the reason why the warning light is
illuminated on the centre display.
If the reason why the
warning light is illu-
minated is due to a dirty windscreen, clean
the windscreen.
If the warning light is illuminated because
of a dirty radar sensor, clean the front em-
blem.
For any other reasons, have the vehicle in-
spected at an expert repairer, we recom-
mend an Authorised Mazda Repairer.
Low Fuel Warning In- dication/Warning
Light The light turns on when the remaining fuel
is about 9.0 L (2.3 US gal, 1.9 Imp gal).NOTE
The light illumination timing may vary be-
cause fuel inside the fuel tank moves around
according to the driving conditions and the
vehicle posture.
Add fuel.
120km/h Warning
Light*
The 120 km/h warning light illuminates
when the vehicle speed exceeds 120 km/h. Lower the vehicle speed.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-54*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning Action to be taken
Seat Belt Warning
Light (Front seat) The seat belt warning light turns on if the
driver or front passenger's seat is occupied
and the seat belt is not fastened with the ig-
nition switched ON.
If the driver or front passenger's seat belt is
unfastened (only when the front passenger's
seat is occupied) and the vehicle is driven at
a speed faster than abo
ut 20 km/h (12 mph),
the warning light flashes. After a short time,
the warning light stops flashing, but re-
mains illuminated. If a seat belt remains un-
fastened, the warning light flashes again for
a given period of time.
NOTE
•If the driver or front passenger's seat belt
is unfastened after th e warning light turns
on, and the vehicle speed exceeds 20 km/h
(12 mph), the warning light flashes again.
•Placing heavy items on the front passeng-
er's seat may cause the front passenger's
seat belt warning function to operate de-
pending on the weight of the item.
•To allow the front passenger seat weight
sensor to function properly, do not place
and sit on an additional seat cushion on
the front passenger's seat. The sensor may
not function properly because the addi-
tional seat cushion could cause sensor in-
terference.
•If a small child is seated on the front pas-
senger's seat, the warning light may not
operate. Fasten the seat belts.
(Red)
Seat Belt Warning
Light (Rear seat)
*
If the rear seat belts are not fastened while
the ignition is switched ON , the driver and
the passenger are alerted by the warning
light.
The warning light opera tes even if there is
no passenger on the rear seat.
NOTE
If a rear seat belt is not fastened by a cer-
tain period of time after the engine has
been started, the warning light turns off. Fasten the seat belts.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.7-55
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

SignalWarning Action to be taken
Low Washer Fluid
Level Warning Indica-
tion/Warning Light
*
This warning light indicates that little wash-
er fluid remains. Add washer fluid (page 6-32).
Door-Ajar/Lift-
gate-Ajar Warning In-
dication/Warning Light The light turns on if a
ny door/liftgate is not
closed securely. Close the door/liftgate securely.
Tyre Pressure Monitoring System Warning Light (Turns on)*
Take the appropriate action and verify that the warning light t
urns off.
Wa r n i n g
When the warning light illuminate s, and the warning beep sound is heard when tyre pressure is too low in one
or more tyres.
WARNING
If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep
sound is heard, decrease vehicle speed immediately and avoid sudden manoeuvring and braking:
If the tyre pressure monitoring system warning light illuminates or flashes, or the tyre pressure warning beep
sound is heard, it is dangerous to drive the vehicle at high speeds, or perform sudden manoeuvring or braking.
Vehicle drivability could worsen and result in an accident.
To determine if you have a slow leak or a flat, pull over to a safe position where you can check the visual condition
of the tyre and determine if you have enough air to proceed to a place where air may be added and the system
monitored again by an expert repairer, we recommend an Authorised Mazda Repairer or a tyre repair station.
Do not ignore the TPMS Warning Light:
Ignoring the TPMS warning light is da ngerous, even if you know why it is illuminated. Have the problem taken
care of as soon as possible before it develops into a more serious situation that could lead to tyre failure and a
dangerous accident.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-56*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Action to be taken
Inspect the tyres and adjust to the specified inflation pressur e (page 6-43).
CAUTION
When replacing/repairing the tyres or wheels or both, have the work done by an Authorised Mazda Repairer, or
the tyre pressure sensors may be damaged.
NOTE
•Perform tyre pressure adjustment when the tyres are cold. Tyre pressure will vary according to the tyre temper-
ature, therefore let the vehicle stand for 1 hour or only drive it 1.6 km (1 mile) or less before adjusting the tyre
pressures. When pressure is adjusted on hot tyres to the cold inflation pressure, the TPMS warning light/beep
may turn on after the tyres cool and pressure drops below specification.
Also, an illuminated TPMS warning light, resulting from th e tyre air pressure dropping due to cold ambient
temperature, may turn off if the ambien t temperature rises. In this case, it will also be necessary to adjust the
tyre air pressures. If the TPMS warn ing light illuminates due to a drop in tyre air pressure, make sure to check
and adjust the tyre air pressures.
•After adjusting the tyre air pressures, it may require some time for the TPMS warning light to turn off. If the
TPMS warning light remains illuminated, drive the vehicle at a speed of at least 25 km/h (16 mph) for 10 mi-
nutes, and then verify that it turns off.
•Tyres lose air naturally over time and the TPMS cannot tell if the tyres are getting too soft over time or you
have a flat. However, when you find one low tyre in a se t of four-that is an indication of trouble; you should
have someone drive the vehicle slowly forward so you can inspect any low tyre for cuts and any metal objects
sticking through tread or sidewall. Pu t a few drops of water in the valve stem to see if it bubbles indicating a
bad valve. Leaks need to be addresse d by more than simply refilling the trouble tyre as leaks are dangerous ―
take it to an expert repairer, we recommend an Authoris ed Mazda Repairer which has all the equipment to fix
tyres, TPMS systems and order the best replacement tyre for your vehicle.
If the warning light illuminates again even after the tyre pressures are adju sted, there may be a tyre puncture.

If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-57
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

KEY Warning Indication/Warning Light*
Take the appropriate action and verify that the warning light turns off.

Signal Cause Action to be taken
(White)
KEY Warning Indica- tion The key battery is dead.
Replace the key battery (page 6-41).
(Red)
(Flashing)
KEY Warning Light The key battery is dead.
Replace the key battery (page 6-41).
The key is not within the operation range. Bring the key into the operation range
(page 3-6).
The key is placed in areas inside the cabin
where it is difficult for the key to be detect-
ed.
A key from another manufacturer similar to
the key is in the operation range. Take the key from another manufacturer
similar to the key out of the operation
range.
Without the ignition switched off, the key is
taken out of the cabin, and then all the
doors are closed. Bring the key back into the cabin.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-58*Some models.
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2