2017 KIA OPTIMA PLUG-IN HYBRID start stop button

• Shift into N (Neutral) if equipped withan Automatic Transaxle / Dual clutch
transmissione.
• Press the CANCEL/O button located on the steering wheel.
• Decrease the vehicle speed lower than the memory speed by approxi‐
mately 20 km/h (12 mph) .
• Decrease the vehicle speed to less than approximately 25 km/h
(15 mph) .
Each of these actions will cancel cruise
control operation (the cruise set indica‐
tor light will go off), but it will not turn the system off. If you wish to resume
cruise control operation, move up the
lever (to RES+) located on your steering wheel. You will return to your previous‐
ly preset speed.To resume cruising speed at
more than approximately 30
km/h (20 mph)
5ZQF
"
0+'
5ZQF
#
0+'-
If any method other than the CRUISE/ button was used to cancel cruising
speed and the system is still activated,
the most recent set speed will auto‐ matically resume when the RES+ switch is pushed.
It will not resume, however, if the vehi‐
cle speed has dropped below approxi‐
mately 30 km/h (20 mph).
To turn cruise control off, do
one of the following:
• Press the CRUISE/ button (the
cruise indicator light will be turned off).
• If your vehicle equipped the speed limit system, press the CRUISE/
button twice. (The cruise indicator
light will be turned off.)
• Turn the engine start/stop button off.
Both of these actions cancel cruise con‐ trol operation. If you want to resume
cruise control operation, repeat the
steps provided in L

• Press the cruise switch.
• Turn the engine start/stop buttonoff.
If you press the cancel O switch once, the set speed limit will cancel, but it will
not turn the system off. If you wish to
reset the speed limit, move the lever up (to RES+) or down (to SET-) to the de‐
sired speed.
0+'-
CAUTION
The L

ADVANCED SMART CRUISE CONTROL SYSTEM (IF EQUIPPED)
1. Cruise indicator
2. Set speed
3. Vehicle-to-vehicle distance
The advanced smart cruise control sys‐
tem allows you to program the vehicle to maintain constant speed and dis‐
tance detecting the vehicle ahead with‐
out depressing the accelerator or brake pedal.
WARNING
For your safety, please read theowner's manual before using the ad‐vanced smart cruise control system.
NOTICE
To activate advanced smart cruise
control, depress the brake pedal at
least once after turning the engine
start/stop button switch to the ON
position or starting the engine. This
is to check if the brake switch which
is important part to cancel advanced
smart cruise control is in normal
condition.
WARNING
•If the advanced smart cruise con‐trol is left on, (cruise indicator inthe instrument cluster illuminated)the smart cruise control can be ac‐tivated unintentionally. Keep thesmart cruise control system off(cruise indicator turn off) whenthe smart cruise control is notused.
•Use the smart cruise control sys‐tem only when traveling on openhighways in good weather.
•Do not use the smart cruise con‐trol when it may not be safe tokeep the car at a constant speed.For instance:-Highway interchange and toll‐gate
-Road surrounded by abnormallymultiple steel constructions(subway construction, steeltunnel, etc)
-Parking lot
-Lanes beside guard rail on aroad
(Continued)

7-59
7
Driving your vehicle

To operate the LDWS, press the switch
with the engine start/stop button in the ON position. The indicator illumi‐
nates white on the cluster.
To cancel the LDWS, press LDWS button
again. The indicator on the cluster will
go off.
0+'-
If you select this symbol, the LDWS
mode on the LCD display will appear.
If your vehicle leaves the lane when the LDWS is operating and vehicle speed
exceeds around 60 km/h, the warning
operates as follows:
0+'-
-FGU
MBOF
EFQBSUJOH
3JHIU
MBOF
EFQBSUJOH
0+'-
1. Visual warning If you leave a lane, the lane you
cross will blink (yellow) and LDWS
indicator will blink green on LCD
during max 3 seconds. 2. Auditory warning
If you leave the lane, the warning
sound operates for maximum 3
seconds.
The color of symbol will change de‐ pending on the condition of LDWS sys‐
tem.
• White color: When you activate
the lane departure warning system by
pressing the LDWS
button, system oper‐
ating conditions arenot satisfied or thesensor does not de‐tect the lane line.
• Green color: When you activate the lane departurewarning system by
pressing the LDWS
button, system oper‐
ating conditions aresatisfied and the sen‐sor detect the laneline.
• Yellow color: When there is a mal‐function with the lane
departure warningsystem.
Driving your vehicle

7-80

BLIND SPOT DETECTION SYSTEM (BSD) (IF EQUIPPED)
06.-
The BSD (Blind spot detection) system
uses a radar sensor to alert the driver while driving.
It senses the rear side territory of the
vehicle and provides information to the
driver. 1. BSD (Blind spot detection)
Warning range is dependent on
your vehicle speed. However, if the
speed of your vehicle is faster by
10 km/h or more than other nearby
vehicles, the warning is not operat‐
ed.
2. LCA (Lane change assist) When vehicles are approaching toyour vehicle at high speed, the
warning is operated.
3. RCTA (Rear cross traffic alert) When your vehicle moves back‐
ward, the sensor detects approach‐
ing vehicles to the left or right side
direction and warning is operated.
WARNING
•Always check the road conditionwhile driving for unexpected situa‐tions even though the BSD (Blindspot detection) system is operat‐ing.
•BSD (Blind spot detection) systemis a system made for convenience.Do not solely rely on the systembut always pay attention to drivesafely.
BSD (Blind spot detection) / LCA
(Lane Change Assist)
Operating conditions
The indicator on the switch will illumi‐
nate when the BSD (Blind spot detec‐ tion) system switch is pressed with the
engine start/stop button switch ON. If
the vehicle speed exceeds 30 km/h (18.6 mph), the system will activate.
If you press the switch again, the
switch indicator and system will be
turned off.
If the engine start/stop button switch is turned OFF and ON the system re‐
turns to the previous state.

7-91
7
Driving your vehicle

• Use your air conditioning sparingly.The air conditioning system is oper‐
ated by engine power so your fuel economy is reduced when you use it.
• Open windows at high speeds can re‐ duce fuel economy.
• Fuel economy is less in crosswinds and headwinds. To help offset some
of this loss, slow down when driving
in these conditions.
Keeping a vehicle in good operating
condition is important both for econo‐
my and safety. Therefore, we recom‐ mend that the system be serviced by
an authorized Kia dealer.
WARNING
nEngine off during motion
Never turn the engine off to coastdown hills or anytime the vehicle isin motion. The power steering andpower brakes will not function prop‐erly without the engine running. In‐stead, keep the engine on and down‐shift to an appropriate gear for en‐gine braking effect. In addition, turn‐
(Continued)
(Continued)
ing off the engine start/stop buttonwhile driving could engage the steer‐ing wheel lock (if equipped) resultingin loss of vehicle steering whichcould cause serious injury or death.
Driving your vehicle
7-98

3. Ensure that button (9) on the com‐pressor is not pressed.
0+')
4. Unscrew the valve cap from thevalve of the flat tire and screw fill‐
ing hose (3) of the sealant bottle
onto the valve.
5. Insert the sealant bottle into the housing (5) of the compressor so
that the bottle is upright.
6. Ensure that the compressor is switched off, position 0.
WARNING
If sealant is dispersed when the in‐jection hose and tire air injectionvalve have not been fully connected,the sealant may overflow and clogthe valve.
0+'"
7. Connect between compressor andthe vehicle power outlet using the
cable and connectors (4).
8. With the engine start/stop button position on or ignition switch posi‐
tion on, switch on the compressor
and let it run for approximately 5~7
minutes to fill the sealant up to
proper pressure. (refer to L

(Continued)
1.Stop the vehicle and shift thetransmission in to "P" position,and then depress the parkingbrake. To ventilate smoke from afire, open the windows if possi‐ble.
2.Turn off the Hybrid system bypushing the Engine Start/StopButton.
3.Leave the vehicle and evacuateto the safety place.
4.Call emergency services for helpand let them know the vehicle isa Hybrid vehicle.
If you have an extinguisher, extin‐guish a fire carefully.Do not touch high voltage cables,connectors and package modules.High voltage components are orangein color.Exposed cables or wires may be visi‐ble inside or outside of the vehicle.Never touch the wires or cables, be‐cause an electrical shock may occurcausing injury or death.
WARNING
If a submersion in water occurs:If your vehicle was flooded and hassoaked carpeting or water on theflooring, you should not try to startthe Hybrid system. Never touch thehigh voltage cables, connectors andpackage modules, because an elec‐trical shock may occur causing injuryor death. High Voltage cables are or‐ange in color.We recommend that the car towedto an authorized Kia dealer.
What to do in an emergency
8-26