2017 KIA OPTIMA PLUG-IN HYBRID battery location

You should refill the fuel tank to pre‐
vent hybrid battery damage.
Refill inverter coolant
This warning message illuminates when
the inverter coolant is nearly empty.
You should refill the inverter coolant.
Check brakes
This warning message illuminates when
the brake performance is low or the re‐ generative brake does not work prop‐
erly due to a failure in the brake sys‐
tem.
In this case, it may take longer for the brake pedal to operate and the braking
distance may become longer.
Stop vehicle and check brakes
This warning message is displayed
when a failure occurs in the brake sys‐ tem.
In this case, park the vehicle in a safe
location and we recommend you to tow
your vehicle to the nearest authorized Kia dealer and have the vehicle inspec‐
ted.
Coasting guide (if equipped)
A chime will sound and the coasting
guide indicator will blink four times to inform the driver when to take the foot
off from the accelerator by anticipating
a decelerating event* based on the analysis of driving routes and road con‐
ditions of the navigation. It encourages
the driver to remove foot from the pedal and allow coasting down the road
with EV motor only. This helps prevent
unnecessary fuel consumption and in‐ creases fuel efficiency. ❈ Example of a deceleration event is
going down an extended hill, slow‐ ing down approaching a toll booth,
and approaching reduced speed
zones.
• User settings
Press the Engine Start/Stop button
and put the shift lever in P (Park). In
the User Settings Mode, select Driv‐
ing Assist, Coasting Guide, and then On to turn on the system. Cancel the
selection of coasting guide to turn off
the system. For the explanation of
the system, press and hold the [OK]
button.
• Operation conditions To activate the system, take the fol‐
lowing procedures. Enter your desti‐
nation information on the navigation
and select the driving route. Select the ECO mode in the Integrated Driv‐
ing Control System. Then, satisfy the
following. - The driving speed should be be‐ tween 60 km/h (37 mph) and
160 km/h (99 mph).
❈ The operating speed may vary due
to difference between instrument
cluster and navigation effected by
tire inflation level.
Unplug vehicle to start (Plug-in
Hybrid)
The message is displayed when you
start the engine without unplugging
the charging cable. Unplug the charging
cable, and then start the vehicle.
Remaining charge time (Plug-in
Hybrid)
The message is displayed to notify the
remaining time to fully charge the bat‐ tery.
Shift to P to charge (Plug-in
Hybrid)
The message is displayed when the
charging connector is plugged with the
shift lever in R (Reverse), N (Neutral) or
D (Drive). Move the shift lever to P
(Park) and re-start the charging proc‐ ess.
Features of your vehicle
5-76

WARNING
nCarbon monoxide
Carbon monoxide poisoning and suf‐focation is possible if the engine isleft running in a poorly ventilated orunventilated location (such as insidea building).
Distributing the sealant
11. Immediately drive approximately7~10 km (4~6 miles or, about 10
min) to evenly distribute the seal‐
ant in the tire.
CAUTION
Do not exceed a speed of 80 km/h(50 mph). If possible, do not fall be‐low a speed of 20 km/h (12 mph).While driving, if you experience anyunusual vibration, ride disturbanceor noise, reduce your speed anddrive with caution until you cansafely pull off of the side of theroad. Call for road side service ortowing.
(Continued)
(Continued)
When you use the Tire Mobility Kit,the tire pressure sensors and wheelmay be stained by sealant. There‐fore, remove the tire pressure sen‐sors and wheel stained by sealantand we recommend to have it in‐spected by an authorized Kia dealer.
Checking the tire inflation
pressure
0+')
1. After driving approximately 7~10 km (4~6 miles, or about 10
minutes), stop at a suitable loca‐
tion. 2. Connect connection hose (10) of
the compressor directly to the tire
valve.
3. Connect between compressor and the vehicle battery using the cable
and connectors.
4. Adjust the tire inflation pressure to 200 kPa (29 psi). With the ignition
switched on, proceed as follows. -
To increase the inflation pres‐sure: Switch on the compressor,
position I. To check the current
inflation pressure setting, briefly switch off the compressor.
WARNING
Do not let the compressor run formore than 10 minutes, otherwisethe device will overheat and may bedamaged.
-To reduce the inflation pressure:
Press the button (9) on the com‐
pressor.

8-19
8
What to do in an emergency

CAUTION
If the inflation pressure is not main‐tained, drive the vehicle a secondtime, refer to Distributing the seal‐ant. Then repeat steps 1 to 4.Use of the TMK may be ineffectualfor tire damage larger than approxi‐mately 4 mm (0.16 in).We recommend that you contact anauthorized Kia dealer if the tire can‐not be made roadworthy with theTire Mobility Kit.
WARNING
The tire inflation pressure must beat least 200 kPa (29 psi). If it is not,do not continue driving.Call for road side service or towing.
Notes on the safe use of the
Tire Mobility Kit
• Park your car at the side of the roadso that you can work with the TMK
away from moving traffic. Place your warning triangle in a prominent place
to make passing vehicles aware of
your location. • To be sure your vehicle will not move,
even when you're on fairly level
ground, always set your parking brake.
• Only use the TMK for sealing/inflation passenger car tires. Do not use on
motorcycles, bicycles or any other
type of tires.
• Do not remove any foreign objects such as nails or screws -that have
penetrated the tire.
• Before using the TMK, read the pre‐ cautionary advice printed on the seal‐ ant bottle!
• Provided the car is outdoors, leave the engine running. Otherwise oper‐
ating the compressor may eventually
drain the car battery.
• Never leave the TMK unattended while it is being used.
• Do not leave the compressor running for more than 10 min. at a time or it
may overheat.
• Do not use the TMK if the ambient temperature is below -30°C (-22°F).
• When the tire and wheel are dam‐ aged, do not use Tire Mobility Kit foryour safety.
Technical data
System voltage: DC 12 V
Working voltage: DC 10 - 15 VAmperage rating: max. 15 A
Suitable for use at temperatures:
-30 ~ +70°C (-22 ~ +158°F)
Max. working pressure: 6 bar (87 psi)Size
Compressor: 168 x 150 x 68 mm (6.6 x 5.9 x 2.7 in)
Sealant bottle: 104 x 85 ø mm
(4.1 x 3.3 ø in.)
Compressor weight: 1.05 kg (2.31 lbs)
Sealant volume: 300 ml (18.3 cu. in.) ❈ Sealant and spare parts can be ob‐
tained and replaced at an author‐
ized vehicle or tire dealer. Empty
sealant bottles may be disposed of
at home. Liquid residue from the
sealant should be disposed of by
your vehicle or tire dealer or in ac‐
cordance with local waste disposal
regulations.
What to do in an emergency
8-20