2017 INFINITI QX30 cruise control

1. Turn signal, wiper, washer, and high beam
switch (P. 2-64, 2-58)
2. Steering-wheel-mounted controls (left side)
(P. 2-15)
3. Ignition switch (P. 3-16)4. Steering-wheel-mounted controls (right
side) (P. 4-3)
5. Light switch
— Headlight (P. 2-62)
— Fog light (P. 2-68)
6. Parking brake (P. 3-25)7. Cruise Control switch
— Cruise Control (P. 5-44)
— Intelligent Cruise Control (P. 2-47)
8. USB connection ports (P. 4-3)
9. Shift lever (P. 5-18)
10. Front cup holders (P. 2-78)
11. INFINITI controller (P. 4-2)
NIC2649
COCKPIT
0-6Illustrated table of contents

1. Turn signal, wiper, washer, and high beam
switch (P. 2-64, 2-58)
2. Steering-wheel-mounted controls (left
side) (P. 2-15)
3. Ignition switch (P. 3-16)4. Steering-wheel-mounted controls (right
side) (P. 4-3)
5. Light switch
— Headlight (P. 2-62)
— Fog light (P. 2-68)
6. Parking brake (P. 3-25)7. Cruise Control switch
— Cruise Control (P. 5-44)
— Intelligent Cruise Control (P. 2-47)
8. USB connection ports (P. 4-3)
9. Shift lever (P. 5-18)
10. Front cup holders (P. 2-78)
11. INFINITI controller (P. 4-2)
NIC2649
COCKPIT
2-2Instruments and controls

SPEEDOMETER AND ODOMETER
This vehicle is equipped with a speedometer
and odometer. The speedometer is located on
the right side of the meter cluster. The odom-
eter is located below the vehicle information
display.
Speedometer
The speedometer indicates vehicle speed.
The speedometer is divided into segments
1,
2and3only on vehicles with Intelligent
Cruise Control.
The segments in the speedometer indicate
which speed range is available (seeDisplays in
the speedometerin the5. Starting and driv-
ingsection).
Odometer/Twin trip odometer
The odometer and the twin trip odometer are
displayed in the Vehicle Information Display
seeVehicle information displayin the5.
Starting and drivingStarting and drivingsec-
tion.
NIC2824ZNIC2824AZWith segments
Instruments and controls2-5

•The coolant is too hot and the engine is no
longer being cooled sufficiently.
Observe the additional display messages in the
vehicle information display.
Stop the vehicle immediately, paying attention
to road and traffic conditions, and switch off the
engine.
Secure the vehicle against rolling away.
Leave the vehicle and keep a safe distance from
the vehicle until the engine has cooled down.
Check the coolant level and top up the coolant,
observing the warning notes (seeIf your ve-
hicle overheatsin the6. In case of emergency
section).
If you have to top up the coolant frequently,
have the engine cooling system checked.
Make sure that the air supply to the engine
radiator is not blocked, e. g. by frozen slush.
Do not start the engine again until the coolant
temperature is below 250
oF (120oC). The
engine may otherwise be damaged.
Low fuel warning light
This light comes on when the fuel level in the
fuel tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches 0 (Empty).There will be a small reserve
of fuel in the tank when the fuel gauge reaches 0
(Empty).
Vehicle Dynamic Control
(VDC) warning light
The VDC warning light blinks when the Vehicle
Dynamic Control (VDC) system is operating,
thus alerting the driver to the fact that the road
surface is slippery and the vehicle is nearing its
traction limits.
You may feel or hear the system working, this is
normal.
The light will continue to blink for a few seconds
after the VDC system stops limiting wheel spin.
Cruise control or Intelligent Cruise Control is
deactivated.
For additional information seeVehicle Dy-
namic Control (VDC) OFF indicator lightin the
2. Instruments and controlssection andVe-
hicle Dynamic Control (VDC) systemin the5.
Starting and drivingStarting and drivingsec-
tion.
INDICATOR LIGHTS
Turn signal/hazard indicator
lights
The appropriate light flashes when the turn
signal switch is activated. Both lights flash
when the hazard switch is turned on.
Low beam indicator light
This light comes on when the switch is turned to
the position:The headlights will come on
and front side, tail, number plate and instru-
ment lights remain on.
Vehicle Dynamic Control (VDC)
OFF indicator light
The light comes on when the Vehicle Dynamic
Control (VDC) has been disabled. This indicates
that the VDC system is not operating.
Disabling the VDC system causes the Forward
Emergency Braking system to become unavail-
able. SeeForward emergency braking (FEB)
system (if equipped)in the5. Starting and
drivingsection for more details.
This light also comes on briefly when the igni-
tion switch is turned to the ON position. The
light will turn off after approximately 1 second if
the VDC system is operational.
Instruments and controls2-13

Video DVD operation (outside Europe only):
It is only possible to use the [Audio] menu to
operate video DVDs on vehicles with navigation
system.
1. Switch on the audio system or navigation
system and select video DVD.
2. Press the
orbutton on the
steering wheel to select the [Audio] menu.
3. To select the next or previous scene, briefly
press
or.
4. To select a scene from the scene list (rapid
scrolling): press and hold the
or. button until the desired scene1has
been reached.
Assistance menu
Depending on the equipment fitted in the ve-
hicle, you have the following options in the
[DriveAssist] menu:
•Showing the assistance graphic
•Activating/deactivating VDC
•Activating/deactivating Forward Emergency
Braking (FEB)
•Activating/deactivating Blind Spot Warning
(BSW)
•Activating/deactivating Lane Departure
Warning (LDW)Showing the distance display
:
1. Press theorbutton on the
steering wheel to select the [DriveAssist]
menu.
2. Press the
orbutton to select
[Distance display].
3. Press the button.
The vehicle information display shows the
Intelligent Cruise Control (ICC) distance dis-
play in the assistance graphic.
The distance display also shows you the
status of and/or information from the follow-
ing driving systems or driving safety sys-
tems:
•Intelligent Cruise Control (ICC)
•Forward Emergency Braking (FEB)
NIC2726NIC2873NIC2729
2-22Instruments and controls

Instrument cluster:
Unit of measurement for distance: The Display
unit Speed-/odometer function allows you to
choose whether certain displays appear in kilo-
meters or miles in the vehicle information dis-
play.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Display Unit Speed-/Odometer] func-
tion.
You will see the selected setting: [miles] or
[km].
5. Press the button to change the setting.
The selected unit of measurement for distance
applies to:
•Digital speedometer in the [Trip] menu.
•Total distance recorder and the trip meter.
•Trip computer.
•Current fuel consumption and approximate
range.
•Navigation instructions in the [Navi] menu.
•Cruise control.
•Speed limiter.
•Intelligent cruise control (ICC).
•Maintenance service interval display.
Switching the additional speedometer on/off.
The [Speedometer (mph)] or [Speedometer (km/
h)] function allows you to choose whether the
vehicle information display in the status area
shows the speed in MPH or in km/h instead of
the outside temperature.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Speedometer (mph)] or [Speedometer
(km/h)] function.
You will see the selected setting: [On] or [off].
5. Press the button to change the setting.Selecting the permanent display function.
You can determine whether the vehicle informa-
tion display permanently shows the outside
temperature or the speed in MPH.
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Instrument Cluster] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Outside Temperature] function.
You will see the selected setting: [outside
temperature] or [Speedometer (mph)].
5. Press the button to save the setting.
Lights
Switching the Adaptive Front Lighting System
on/off:
1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
Instruments and controls2-25

Message Possible causes/consequences and solutions
[Emergency Brake
Inoperative]Forward Emergency Braking is temporarily inoperative due to a malfunction.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Radar Sensor (See
Operator’s Manual):]At least one of the following driving systems or driving safety systems is temporarily restricted or inoperative:
•Forward Emergency Braking•Intelligent Cruise Control
Possible causes:
•The sensors in the radiator trim and/or in the bumpers are dirty.•The function of the driving system and/or driving safety system is impaired due to heavy rain or snow.
A warning tone also sounds.
Once the causes listed above no longer apply, the display message goes out. All driving systems/driving safety systems are operative
again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions
2. Secure the vehicle against rolling away.
3. Switch off the engine.
4. Clean the sensors in the following locations:
- In the radiator trim
- In the front bumper
- In the rear bumper, particularly in the middle of the rear bumper.
5. Restart the engine. The display message disappears.
[SRS Malfunction Service
Required]The restraint system needs servicing. Thewarning light also lights up in the combination meter.
It is recommended you visit an INFINITI retailer for these services.
Unless checked and repaired, the Supplemental Restraint Systems and/or the pretensioner seat belt may not function properly.
WARNING
If this light is on, it could mean that the front air bag, side air bag, curtain air bag systems and/or pretensioner systems will not operate in
an accident. To help avoid injury to yourself or others, have your vehicle checked as soon as possible. It is recommended you visit an INFINITI
retailer for this service.
For further information about the restraint system, seeSupplemental Restraint System (SRS)in the1. Safety — seats, seat belts and
supplemental restraint systemsection.
Instruments and controls2-37

Message Possible causes/consequences and solutions
[Blind Spot Warning Not
Available When Towing a
Trailer See Operator’s
Manual]Blind Spot Warning is deactivated while towing a trailer.
You have established the electrical connection between the trailer and your vehicle.
Press on the steering wheel to confirm the display message.
[Blind Spot Warning
Inoperative]Blind Spot Warning (BSW) is faulty.
The BSW indicator lights also light up.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Canceled] The driver’s door is open and the driver’s seat belt has not been fastened.
Repeat the parking process with the seat belt fastened and the driver’s door closed.
You inadvertently touched the steering wheel while steering intervention was active.
While steering intervention is active, make sure not to touch the steering wheel.
The vehicle has started to skid and VDC has intervened.
Use Intelligent Park Assist again later.
[Park Assist Inoperative] You have just carried out a large number of turning or parking maneuvers.
Intelligent Park Assist will become available again after approximately ten minutes.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Restart the engine.
If the display message continues to be displayed, have the system checked. It is recommended you visit an INFINITI retailer for this
service.
The parking sensor system is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Finished] The vehicle is parked. A warning tone also sounds.
The display message disappears automatically.
[ICC Off]
Intelligent Cruise Control has been deactivated (seeIntelligent Cruise Control (ICC) system (Full speed range) (if equipped)in the5.
Starting and drivingsection).
If it was not deactivated by the driver, a warning tone also sounds.
Instruments and controls2-47