•The coolant is too hot and the engine is no
longer being cooled sufficiently.
Observe the additional display messages in the
vehicle information display.
Stop the vehicle immediately, paying attention
to road and traffic conditions, and switch off the
engine.
Secure the vehicle against rolling away.
Leave the vehicle and keep a safe distance from
the vehicle until the engine has cooled down.
Check the coolant level and top up the coolant,
observing the warning notes (seeIf your ve-
hicle overheatsin the6. In case of emergency
section).
If you have to top up the coolant frequently,
have the engine cooling system checked.
Make sure that the air supply to the engine
radiator is not blocked, e. g. by frozen slush.
Do not start the engine again until the coolant
temperature is below 250
oF (120oC). The
engine may otherwise be damaged.
Low fuel warning light
This light comes on when the fuel level in the
fuel tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches 0 (Empty).There will be a small reserve
of fuel in the tank when the fuel gauge reaches 0
(Empty).
Vehicle Dynamic Control
(VDC) warning light
The VDC warning light blinks when the Vehicle
Dynamic Control (VDC) system is operating,
thus alerting the driver to the fact that the road
surface is slippery and the vehicle is nearing its
traction limits.
You may feel or hear the system working, this is
normal.
The light will continue to blink for a few seconds
after the VDC system stops limiting wheel spin.
Cruise control or Intelligent Cruise Control is
deactivated.
For additional information seeVehicle Dy-
namic Control (VDC) OFF indicator lightin the
2. Instruments and controlssection andVe-
hicle Dynamic Control (VDC) systemin the5.
Starting and drivingStarting and drivingsec-
tion.
INDICATOR LIGHTS
Turn signal/hazard indicator
lights
The appropriate light flashes when the turn
signal switch is activated. Both lights flash
when the hazard switch is turned on.
Low beam indicator light
This light comes on when the switch is turned to
the position:The headlights will come on
and front side, tail, number plate and instru-
ment lights remain on.
Vehicle Dynamic Control (VDC)
OFF indicator light
The light comes on when the Vehicle Dynamic
Control (VDC) has been disabled. This indicates
that the VDC system is not operating.
Disabling the VDC system causes the Forward
Emergency Braking system to become unavail-
able. SeeForward emergency braking (FEB)
system (if equipped)in the5. Starting and
drivingsection for more details.
This light also comes on briefly when the igni-
tion switch is turned to the ON position. The
light will turn off after approximately 1 second if
the VDC system is operational.
Instruments and controls2-13
Tires
Message Possible causes/consequences and solutions
[Please Correct Tire
Pressure]The tire pressure is too low in at least one of the tires, or the tire pressure difference between the wheels is too great.
1. Check the tire pressures at the next opportunity (seeWheels and tiresin the8. Do-it-yourselfsection)
2. If necessary, correct the tire pressure.
3. Restart the tire pressure monitoring system (seeRestarting TPMSin the5. Starting and drivingsection)
[Check Tire(s)] The tire pressure in one or more tires has dropped significantly The wheel position is displayed in the vehicle information display
A warning tone also sounds.
WARNING
Underinflated tires pose the following risks:•The tires may burst, especially as the load and vehicle speed increase.•The tires may wear excessively and/or unevenly, which may greatly impair tire traction.•The driving characteristics, as well as steering and braking, may be greatly impaired.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (seeFlat tirein the6. In case of emergencysection).
4. Check the tire pressures and, if necessary, correct the tire pressure.
[Warning Tire Malfunction] The tire pressure in one or more tires has dropped suddenly. The wheel position is displayed in the vehicle information display.
WARNING
If you drive with a flat tire, there is a risk of the following hazards:•A flat tire affects the ability to steer or brake the vehicle.•You could lose control of the vehicle.•Continued driving with a flat tire will cause excessive heat buildup and possibly a fire.
There is a risk of an accident.
1. Stop the vehicle without making any sudden steering or braking maneuvers. Pay attention to the traffic conditions as you do so.
2. Secure the vehicle against rolling away.
3. Check the tires and, if necessary, follow the instructions for a flat tire (seeFlat tirein the6. In case of emergencysection).
2-50Instruments and controls
Mode Screen display
All Track Repeat
All
1 Folder Repeat
1 Folder
1 Track Repeat
1 Track
All Random
All
1 Folder Random
1 Folder
11Folder number:
This indicates the folder, artist or album
number and the total number of folders/
lists.
USB memory device player operation
Activation and playing:
USB memory device mode can also be activated
from the audio source list and the audio source
bar by the touch panel operation or by pushing
Selecting audio source
Main audio buttons
To play the USB memory device touch [
],
and to pause the USB memory touch []on
the USB operation screen.
Selecting play list
:
Select a play list by touching an icon in the USB
menu.
•Folder/Track (List)
•Artist (List)
•Album (List)
•Previous List
Skipping tracks/folders
:
Push
previous track.
To skip to the next or previous folder, Push
Fast-forwarding/rewinding
:
Push and hold
forward or rewind the track. Release
Scanning
:
Touch [Scan] on the display to scan the tracks in
the USB memory device. While scanning, the
USB memory device will play the first 10 sec-
onds of each track and move on to the next
track. Touching [Scan] again within the 10 sec-
onds will stop scanning.
Changing play mode
:
Touch [Play Mode] on the display to select the
play mode.
Only one of the two connected USB memory
devices can be operated by the voice recogni-
tion system.
IPOD PLAYER
Connecting iPod
WARNING
Do not connect, disconnect or operate the iPod
while driving. Doing so can be a distraction. If
distracted you could lose control of your ve-
hicle and cause an accident or serious injury.
CAUTION
•Do not force the iPod device into the USB
port. Inserting the iPod cable tilted or up-
side down into the port may damage the
port. Make sure that the iPod cable is con-
nected correctly to the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the iPod cable out of the port.
This could damage the port and the cover.
•Do not leave the iPod cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to your device manufacturer’s owner in-
formation regarding the proper use and care of
the device.
Display screen, heater and air conditioner, and audio system4-75
Intelligent Cruise Control (ICC) system
(Full speed range) (if equipped)..............5-47
ICC system operation..................5-48
ICC switch (cruise control lever)...........5-49
ICC system display and indicators..........5-49
Operating ICC.......................5-50
ICC Limitations......................5-54
Tips for driving with the ICC system.........5-55
System temporarily unavailable............5-58
System maintenance..................5-59
Forward emergency braking (FEB) system
(if equipped).........................5-60
FEB system operation..................5-61
Turning the FEB system on/off............5-63
FEB system limitations.................5-64
System temporarily unavailable............5-65
System maintenance..................5-66
FCC Notice........................5-66
Active sound enhancement................5-67
Active sound enhancement..............5-67
Intelligent Parking Assist (IPA) (if equipped)......5-68
Important safety notes.................5-68
Detecting parking spaces...............5-69
Parking..........................5-70
Exiting a parking space.................5-72
Canceling IPA.......................5-73Parking sensor system (if equipped)...........5-73
Parking sensor overview................5-75
Range of the sensors..................5-79
Parking sensor system OFF switch..........5-79
Parking sensor function settings...........5-80
Problems with parking sensor system........5-81
Break-in schedule......................5-81
Fuel efficient driving tips..................5-82
Increasing fuel economy..................5-83
Four-Wheel Drive (4WD) (if equipped)
..........5-83
Parking............................5-84
Switching off the engine................5-85
Extended parking....................5-86
Electric power steering system..............5-86
Brake system.........................5-87
Brake precautions....................5-87
Anti-lock Braking System (ABS)............5-88
Vehicle Dynamic Control (VDC) system.........5-90
Traction Control System (TCS).............5-91
Characteristics of VDC..................5-91
EBD (electronic brake force distribution)......5-92
Steer Control.......................5-92
Hill Start Assist (HSA)....................5-93
Cold weather driving....................5-93
Freeing a frozen door lock...............5-93
Antifreeze.........................5-93
The Vehicle Dynamic Control (VDC) system uses
various sensors to monitor driver inputs and
vehicle motion. Under certain driving condi-
tions, the VDC system helps to perform the
following functions.
•Controls brake pressure to reduce wheel slip
on one slipping drive wheel so power is
transferred to a non slipping drive wheel on
the same axle.
•Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function).
•Controls brake pressure at individual wheels
and engine output to help the driver maintain
control of the vehicle in the following condi-
tions:
– understeer (vehicle tends to not follow
the steered path despite increased steer-
ing input)
– oversteer (vehicle tends to spin due to
certain road or driving conditions).
The VDC system can help the driver to maintain
control of the vehicle, but it cannot prevent loss
of vehicle control in all driving situations.When the VDC system operates, the VDC warn-
ing light in the instrument panel flashes so note
the following:
•The road may be slippery or the system may
determine some action is required to help
keep the vehicle on the steered path.
•You may feel a pulsation in the brake pedal
and hear a noise or vibration from under the
hood. This is normal and indicates that the
VDC system is working properly.
•Adjust your speed and driving to the road
conditions.
SeeVehicle Dynamic Control (VDC) warning
lightin the2. Instruments and controlssec-
tion.
If a malfunction occurs in the system, the VDC
warning light
illuminates in the instrument
panel. The VDC system automatically turns off.
WARNING
•The VDC system is designed to help the
driver maintain stability but does not pre-
vent accidents due to abrupt steering opera-
tion at high speeds or by careless or danger-
ous driving techniques. Reduce vehicle
speed and be especially careful when driv-
ing and cornering on slippery surfaces and
always drive carefully.
•Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings
and wheels are not INFINITI recommended
for your vehicle or are extremely deterio-
rated, the VDC system may not operate
properly. This could adversely affect vehicle
handling performance, and the VDC warning
light
may illuminate.
•If brake related parts such as brake pads,
rotors and calipers are not INFINITI recom-
mended or are extremely deteriorated, the
VDC system may not operate properly and
the VDC warning light
may illuminate.
•If engine control related parts are not
INFINITI recommended or are extremely de-
teriorated, the VDC warning light
may
illuminate.
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
5-90Starting and driving
•When driving on extremely inclined sur-
faces such as higher banked corners, the
VDC system may not operate properly and
the VDC warning light
may illuminate.
Do not drive on these types of roads.
•When driving on an unstable surface such
as a turntable, ferry, elevator or ramp, the
VDC warning light
may illuminate. This
is not a malfunction. Restart the engine af-
ter driving onto a stable surface.
•If wheels or tires other than the INFINITI
recommended ones are used, the VDC sys-
tem may not operate properly and the VDC
warning light
may illuminate.
•The VDC system is not a substitute for win-
ter tires or tire chains on a snow covered
road.
•If VDC is malfunctioning, VDC is unable to
stabilize the vehicle. In addition, other driv-
ing safety systems are switched off. This
increases the risk of skidding and an acci-
dent. Drive on carefully. Have VDC checked.
It is recommended you visit an INFINITI re-
tailer for this service.
CAUTION
•When VDC is deactivated, theVDC
OFF warning light lights up continuously.
•If both thewarning light andwarning light are lit continuously, VDC is
not available due to a malfunction.
TRACTION CONTROL SYSTEM (TCS)
The Traction Control System (TCS) is part of
VDC..
Traction control brakes the drive wheels indi-
vidually if they spin. This enables you to pull
away and accelerate on slippery surfaces, for
example if the road surface is slippery on one
side. In addition, more drive torque is trans-
ferred to the wheel or wheels with traction.
Traction control remains active if you deactivate
VDC.
CHARACTERISTICS OF VDC
If theVDC warning light goes out before
beginning the journey, VDC is automatically
active.
If VDC intervenes, the
VDC warning lamp
flashes in the combination meter.If VDC intervenes:
•Do not deactivate VDC under any circum-
stances.
•When pulling away, only depress the accel-
erator pedal as far as is necessary.
•Adapt your driving style to suit the prevail-
ing road and weather conditions.
Deactivating/activating VDC
WARNING
If you deactivate VDC, VDC no longer stabilizes
the vehicle. There is an increased risk of skid-
ding and an accident.
Only deactivate VDC in the situations de-
scribed in the following section.
You can select between the following statuses
of VDC:
•VDC is activated.
•VDC is deactivated.
It may be best to deactivate VDC in the follow-
ing situations:
•When using snow chains.
•In deep snow.
•On sand or gravel.
Starting and driving5-91
NOTE
Activate VDC as soon as the situations described
above no longer apply. VDC will otherwise not be
able to stabilize the vehicle if the vehicle starts
to skid or a wheel starts to spin.
You can activate/deactivate VDC using the ve-
hicle information display. To activate/
deactivate VDC:
1. Start the engine
2. Press the
orbutton on the
steering wheel to select the [DriveAssist]
menu in the vehicle information display.
3. Press the
orbutton to select
VDC.
4. Press the
wheel. The current selection is displayed.
5. To activate/deactivate: press the
ton again.
VDC is deactivated if the
warning light
in the combination meter lights up continu-
ously when the engine is running.
Characteristics when VDC is deactivated
:
If VDC is deactivated and one or more wheels
start to spin, theVDC warning lamp
flashes in the combination meter. In such situ-
ations, VDC will not stabilize the vehicle.If you deactivate VDC:
•VDC no longer intervenes in understeer or
oversteer situations.
•Engine torque is no longer limited and the
drive wheels are able to spin.
The spinning of the wheels results in a
cutting action, so the tires cut through the
loose surface until the hit solid ground,
giving better traction.
•Traction control is still activated.
•VDC still provides support when you brake.
EBD (ELECTRONIC BRAKE FORCE
DISTRIBUTION)
EBD monitors and controls the brake pressure
on the rear wheels to help improve handling
during braking.
WARNING
If EBD is malfunctioning, the EBD [Inoperative
See Operator’s Manual] warning is displayed
in the vehicle information display. The
VDC warning lamp may also light up.
If EBD is malfunctioning as a result of a VDC
malfunction, the rear wheels can lock, e.g. un-
der full braking. This increases the risk of skid-
ding and an accident.You should therefore adapt your driving style
to the different handling characteristics. Have
the brake system checked. It is recommended
you see an INFINITI retailer.
STEER CONTROL
STEER CONTROL helps you by transmitting a
noticeable steering force to the steering wheel
in the direction required for vehicle stabilisa-
tion.
This steering support is provided in particular if:
•Both right wheels or both left wheels are on
a wet or slippery road surface when you
brake.
•The vehicle starts to skid.
WARNING
No steering support is provided from STEER
CONTROL, if:
•VDC is malfunctioning.
•The steering is faulty.
Power steering will, however, continue to
function.
5-92Starting and driving
TIRE EQUIPMENT
1. SUMMER tires have a tread designed to
provide superior performance on dry pave-
ment. However, the performance of these
tires will be substantially reduced in snowy
and icy conditions. If you operate your ve-
hicle on snowy or icy roads, INFINITI recom-
mends the use of MUD & SNOW or ALL
SEASON TIRES on all four wheels. It is rec-
ommended that you visit an INFINITI retailer
for the tire type, size, speed rating and
availability information.
2. For additional traction on icy roads, studded
tires may be used. However, some U.S.
states and Canadian provinces prohibit their
use. Check local, state and provincial laws
before installing studded tires.
Skid and traction capabilities of studded snow
tires, on wet or dry surfaces, may be poorer than
that of non-studded snow tires.
3. Tire chains may be used if desired. Make
sure they are the proper size for the tires on
your vehicle and are installed according to
the chain manufacturer’s instructions. Use
chain tensioners when recommended by the
tire chain manufacturer to ensure a tight fit.
Loose end links of the tire chains must be
secured or removed to prevent the possibil-
ity of whipping action damage to the fendersor underbody. In addition, drive at a reduced
speed, otherwise, your vehicle may be dam-
aged and/or vehicle handling and perfor-
mance may be adversely affected.
SPECIAL WINTER EQUIPMENT
It is recommended that the following items be
carried in the vehicle during the winter:
•A scraper and stiff-bristled brush to remove
ice and snow from the windows.
•A sturdy, flat board to be placed under the
jack to give it firm support.
•A shovel to dig the vehicle out of snowdrifts.
•Extra washer fluid to refill the windshield
washer fluid reservoir.
DRIVING ON SNOW OR ICE
WARNING
•Wet ice (32°F, 0°C and freezing rain), very
cold snow or ice can be slick and very hard
to drive on. The vehicle will have much less
traction or “grip” under these conditions.
Try to avoid driving on wet ice until the road
is salted or sanded.
•Whatever the condition, drive with caution.
Accelerate and slow down with care. If ac-
celerating or downshifting too fast, the
drive wheels will lose even more traction.
•Allow more stopping distance under these
conditions. Braking should be started
sooner than on dry pavement.
•Allow greater following distances on slip-
pery roads.
•Watch for slippery spots (glare ice). These
may appear on an otherwise clear road in
shaded areas. If a patch of ice is seen ahead,
brake before reaching it. Try not to brake
while on the ice, and avoid any sudden
steering maneuvers.
•Do not use cruise control on slippery roads.
•Snow can trap dangerous exhaust gas under
your vehicle. Keep snow clear of the exhaust
pipe and from around your vehicle.
5-94Starting and driving