2017 INFINITI QX30 change time

ON-PAVEMENT AND OFF-ROAD
DRIVING
This vehicle will handle and maneuver differ-
ently from an ordinary passenger car because it
has a higher center of gravity for off-road use. As
with other vehicles with features of this type,
failure to operate this vehicle correctly may re-
sult in loss of control or an accident.
For additional information, refer to “On-
pavement and off-road driving precautions”,
“Avoiding collision and rollover” and “Driving
safety precautions” in the “Starting and driv-
ing” section of this manual.
MODIFICATION OF YOUR VEHICLE
This vehicle should not be modified. Modifica-
tion could affect its performance, safety or dura-
bility and may even violate governmental regu-
lations. In addition, damage or performance
problems resulting from modifications may not
be covered under INFINITI warranties.
WARNING
Installing an aftermarket On-Board Diagnostic
(OBD) plug-in device that uses the port during
normal driving, for example remote insurance
company monitoring, remote vehicle diagnos-
tics, telematics or engine reprogramming, may
cause interference or damage to vehicle sys-tems. We do not recommend or endorse the
use of any aftermarket OBD plug-in devices,
unless specifically approved by INFINITI. The
vehicle warranty may not cover damage
caused by any aftermarket plug-in device.
WHEN READING THE MANUAL
This manual includes information for all fea-
tures and equipment available on this model.
Features and equipment in your vehicle may
vary depending on model, trim level, options
selected, order, date of production, region or
availability. Therefore, you may find information
about features or equipment that are not in-
cluded or installed on your vehicle.
All information, specifications and illustrations
in this manual are those in effect at the time of
printing. INFINITI reserves the right to change
performance, design or component suppliers
without notice and without obligation.
From time to time, INFINITI may update or revise
this manual to provide Owners with the most
accurate information currently available. Please
carefully read and retain with this manual all
revision updates sent to you by INFINITI to
ensure you have access to accurate and up-to-
date information regarding your vehicle. Cur-
rent versions of vehicle Owner’s Manuals andany updates can also be found in the Owner
section of the INFINITI website at https://
owners.infinitiusa.com/owners/navigation/
manualsandGuides. If you have questions con-
cerning any information in your Owner’s
Manual, contact INFINITI Consumer Affairs. See
the INFINITI CUSTOMER CARE PROGRAM page in
this Owner’s Manual for contact information.IMPORTANT INFORMATION ABOUT
THIS MANUAL
You will see various symbols in this manual.
They are used in the following ways:
WARNING
This is used to indicate the presence of a haz-
ard that could cause death or serious personal
injury. To avoid or reduce the risk, the proce-
dures must be followed precisely.
CAUTION
This is used to indicate the presence of a haz-
ard that could cause minor or moderate per-
sonal injury or damage to your vehicle. To
avoid or reduce the risk, the procedures must
be followed carefully.

•Right after inflation, several side air bag
and curtain air bag system components will
be hot. Do not touch them; you may severely
burn yourself.
•No unauthorized changes should be made
to any components or wiring of the side air
bag and curtain air bag systems. This is to
prevent damage to or accidental inflation of
the side air bag and curtain air bag systems.
•Do not make unauthorized changes to your
vehicle’s electrical system, suspension sys-
tem or side panel. This could affect proper
operation of the curtain air bag systems.
•Tampering with the side air bag system
may result in serious personal injury. For
example, do not change the front seats by
placing material near the seatbacks or by
installing additional trim material, such as
seat covers, around the side air bag.
•It is recommended that you visit an INFINITI
retailer for work on and around the front air
bag. It is also recommended that you visit
an INFINITI retailer for installation of electri-
cal equipment. The SRS wiring harnesses*
should not be modified or disconnected. Un-
authorized electrical test equipment and
probing devices should not be used on the
side air bag or curtain air bag systems.
Driver and passenger supplemental
knee air bags
The driver’s knee air bag deploys under the
steering column, while the passenger’s knee air
bag deploys under the glove box. All of the
information, cautions and warnings in this
manual apply and must be followed. The driv-
er’s and passenger’s knee air bags are trig-
gered together with the front air bag. The knee
air bags are designed to inflate in higher sever-
ity frontal collisions, although they may inflate
if the forces in another type of collision are
similar to those of a higher severity frontal
impact. They may not inflate in certain colli-
sions.
Vehicle damage (or lack of it) is not always an
indication of proper knee air bag operation.
When a knee air bag inflates, a fairly loud noise
may be heard, followed by release of smoke.
This smoke is not harmful and does not indicate
a fire. Care should be taken not to inhale it, as
it may cause irritation and choking. Those with
a history of a breathing condition should get
fresh air promptly
The knee air bags help to cushion the impact
force on the knees of the driver and front
passenger. They can help reduce serious inju-
ries. However, an inflating knee air bag maycause abrasions or other injuries. The knee air
bag provides restraint to the lower body.
The knee air bag inflates quickly in order to help
protect the occupants. Because of this, the
force of the knee air bag inflating can increase
the risk of injury if the occupant is too close to,
or is against, this air bag module during infla-
tion. The knee air bag will deflate quickly after
the collision is over OR the knee air bag will
remain inflated for a short time.
The knee air bags operate only when the ignition
switch is placed in the ON position. After placing
the ignition switch in the ON position, the
supplemental air bag warning light illuminates.
The supplemental air bag warning light will turn
off a few seconds after the engine starts if the
system is operational.
WARNING
•Do not place any objects between the knee
bolster and the driver’s seat. Such objects
may become dangerous projectiles and
cause injury if a knee air bag inflates.
•Right after inflation, the knee air bag sys-
tem components will be hot. Do not touch
them; you may severely burn yourself.
Safety — seats, seat belts and supplemental restraint system1-53

4. Press theorbutton to select
the [Adaptive front lighting system] function.
If the [Adaptive front lighting system] func-
tion has been switched on, the cone of light
and the
symbol in the vehicle infor-
mation display are shown in orange.
5. Press the button to save the setting.
When you switch the [Adaptive front lighting
system] function on, you activate the following
functions:
•Freeway mode
•Active light function
•Cornering light function
If you set the low beam headlights for driving
on the right/left, the vehicle information display
shows the [Adaptive front lighting system: Sys-
tem Inoperative Inactive For Left-side Traffic] or
[Adaptive front lighting system: System Inop-
erative Inactive for Right-side Traffic] display
message instead of the [Adaptive front lighting]
function in the [Light] submenu.
For further information about the Adaptive Front
Lighting system, seeAdaptive front lighting
system (LED headlight only) (if equipped)later
in this sectionSetting the low beam headlights for driving on
the left/right
:
This function is only available on vehicles with
the Adaptive Front Lighting System (seeAdap-
tive front lighting system (LED headlight only) (if
equipped)later in this section).
1. Press the
orbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Low-b. Headl. Setting For:] function.
You will see the selected setting: [Right-side
Traffic] or [Left-side Traffic].
5. Press the button to save the setting.
If you change the setting, conversion does
not take place until the next time the vehicle
is stationary.
If you set the low beam headlights for driving
on the right/left, then freeway mode is unavail-
able. This is only deactivated if the setting for
driving on the left/right is set opposite to your
vehicle’s country version.
An INFINITI retailer can set the low beam head-
lights for driving on the left/right.Setting the brightness of the ambient lighting
:
1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Light] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Ambient Light Brightness] function.
You will see the selected setting.
5. Change the setting with .
If you change the setting, conversion does
not take place until the next time the vehicle
is stationary.
6. Press the
orbutton to adjust
the brightness to a level from [Off] to [Level
5] (bright).
7. Press the or
button to save the
setting.
2-26Instruments and controls

COMBINATION SWITCH
1Turn signal, right
2Turn signal, left
3High beam headlights
4Headlight flasher
Turn signal
Move the lever up or down to signal the turning
direction. When the turn is completed, the turn
signal cancels automatically.
Lane change signal
Move the lever up or down until the turn signal
begins to flash, but the lever does not latch, to
signal a lane change. Hold the lever until the
lane change is completed. Move the lever up or
down until the turn signal begins to flash, but
the lever does not latch, and release the lever.
The turn signal will automatically flash threetimes. Choose the appropriate method to signal
a lane change based on road and traffic condi-
tions.
High beam headlights
To switch on the high beam headlights:
•Turn the ignition switch to the ON position or
start the engine.
•Turn the light switch toor.
•Press the combination switch beyond the
pressure point in the direction of arrow
3.
In theposition, the high beam head-
lights are only switched on when it is dark
and the engine is running.
The blue
indicator light in the combi-
nation meter lights up when the high beam
headlights are switched on.
To switch off the high beam headlights:
•Move the combination switch back to its
normal position. The blueindicator
light in the combination meter goes out.
NOTE
Vehicles with High beam Assist: when High
beam Assist is active, it controls activation and
deactivation of the high beam headlights (see
High beam assist (LED headlight only)later in
this section)
ADAPTIVE FRONT LIGHTING SYSTEM
(LED HEADLIGHT ONLY) (IF EQUIPPED)
The Adaptive Front Lighting System is a system
that adjusts the headlights automatically to suit
the prevailing driving and weather conditions. It
offers advanced functions for improved illumi-
nation of the road surface, e.g. depending on
the vehicle speed or weather conditions. The
system includes the active light function, cor-
nering light function and freeway mode. The
system is only active when it is dark.
You can activate or deactivate the “Adaptive
Front Lighting System” function using the ve-
hicle information display (seeSwitching the
Adaptive Front Lighting System on/offearlier in
this section)
NIC2618
2-64Instruments and controls

HIGH BEAM ASSIST (LED HEADLIGHT
ONLY)
You can use this function to set the headlights
to change between low beam and high beam
automatically. The system recognizes vehicles
with their lights on, either approaching from the
opposite direction or traveling in front of your
vehicle, and consequently switches the head-
lights from high beam to low beam.
The system automatically adapts the low beam
headlight range depending on the distance to
the other vehicle. Once the system no longer
detects any other vehicles, it switches on the
high beam headlights again.
The system’s optical sensor is located behind
the windshield near the overhead control panel.
WARNING
•The high beam assist system is a conve-
nience but is not a substitute for safe driv-
ing operation. The driver should remain
alert at all times, ensure safe driving prac-
tices and switch the high beams and low
beam manually when necessary.
•The high beam or low beam may not switch
automatically under the following condi-
tions. Switch the high beam and low beam
manually.
–During bad weather (rain, fog, snow,
wind, etc.).
–When a light source similar to a head-
light or tail light is in the vicinity of the
vehicle.
–When the headlights of the oncoming
vehicle or the leading vehicle are turned
off, when the color of the light is affected
due to foreign materials on the lights, or
when the light beam is out of position.
–When there is a sudden, continuous
change in brightness.
–When driving on a road that passes over
rolling hills, or a road that has level dif-
ferences.
–When driving on a road with many
curves.–When a sign or mirror-like surface is
reflecting intense light towards the front
of the vehicle.
–When the container, etc. being towed by
a leading vehicle is reflecting intense
light.
–When a headlight on your vehicle is
damaged or dirty.
–When the vehicle is leaning at an angle
due to a punctured tire, being towed, etc.
•The timing of switching the low beam and
high beam may change under the following
situations.
–The brightness of the headlights of the
oncoming vehicle or leading vehicle.
–The movement and direction of the on-
coming vehicle and the leading vehicle.
–When only one light on the oncoming
vehicle or the leading vehicle is illumi-
nated.
–When the oncoming vehicle or the lead-
ing vehicle is a two-wheeled vehicle.
–Road conditions (incline, curve, the road
surface, etc.).
–The number of passengers and the
amount of luggage.
•High beam Assist does not recognize road
users:
–Who have no lights, e.g. pedestrians.
NDS595
2-66Instruments and controls

•If another hand-held transmitter is available
for the same garage door drive, repeat the
same programing steps with this hand-held
transmitter
5. Before performing these
steps, make sure that new batteries have
been installed in the hand-held transmitter
5.
•Note that some hand-held transmitters only
transmit for a limited amount of time (the
indicator lamp on the hand-held transmitter
goes out). Press button
6on remote hand-
held transmitter
5again before transmis-
sion ends.
•Align the antenna cable of the garage door
opener unit. This can improve signal
reception/ transmission.
If you have any questions or are having diffi-
culty programming your HomeLink® buttons,
refer to the HomeLink® web site at:
www.homelink.com or 1-800-355-3515.
OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER
The HomeLink® Universal Transceiver, after it is
programmed, can be used to activate the pro-
grammed device.
1. Turn the ignition key to the ON position.
2. Press button
2,3or4which you have
programed to operate the garage door.
Garage door system with a fixed code: indi-
cator lamp
1lights up green
Garage door system with a rolling code:
indicator lamp
1flashes green.
The transmitter will transmit a signal as long as
the button is pressed. The transmission is
halted after a maximum of ten seconds and
indicator lamp
1lights up yellow. Press button
2,3or4again if necessary.
For convenience, the hand-held transmitter of
the device may also be used at any time.
CLEARING THE PROGRAMMED
INFORMATION
Make sure that you clear the memory of the
integrated garage door opener before selling
the vehicle.
1. Turn the ignition key to the ON position.
2. Press and hold buttons
2and4.
The indicator lamp initially lights up yellow
and then green.
3. Release buttons
2and4.
The memory of the integrated garage door
opener in the rear-view mirror is cleared.
IF YOUR VEHICLE IS STOLEN
If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink®. Consult the
Owner’s Manual of each device or call the
manufacturer of those devices for additional
information or contact an INFINITI retailer.
Instruments and controls2-89

Models with navigation system:
Touch[<] / [>]to switch between air conditioner
status and navigation route information screen.
ITEMS TO BE SET INITIALLY
The initial setting operations included in this
section should be performed before using the
system for the first time.
Screen settings
The display can be turned on/off and the image
quality of the display can be adjusted in this menu.
1. Push

Clock settings
Clock settings can be changed.
1. Push