2017 INFINITI QX30 engine oil capacity

1. Park the vehicle on a level surface and apply
the parking brake.
2. Start the engine and let it idle until it
reaches the normal operating temperature,
then turn it off.
3. Remove the oil filler cap by turning it
counterclockwise.
4. Remove the engine undershield.
5. Place a large drain pan under the drain plug.
6. Remove the drain plug with a wrench by
turning it counterclockwise and completely
drain the oil. If the oil filter is to be changed,
remove and replace it at this time. For
additional information, refer toChanging
engine oil filterlater in this section.
•Waste oil must be disposed of properly.
•Check your local regulations.
7. Clean and reinstall the drain plug and a new
washer. Securely tighten the drain plug with
a wrench. Do not use excessive force. Drain
plug tightening torque: 22 ft-lb, 30 N•m
8. Refill engine with recommended oil through
the oil filler opening, then install the oil filler
cap securely.
For additional information on drain and refill
capacity, refer toRecommended fluids/
lubricants and capacitiesin the9. Maintenance
and Schedulessection.
The drain and refill capacity depends on the
oil temperature and drain time. Use these
specifications for reference only. Always use
the dipstick to determine when the proper
amount of oil is in the engine.
9. Start the engine. Check for leakage around
the drain plug and oil filter. Correct as
required.
10. Turn the engine off and wait more than 10
minutes. Check the oil level with the dip-
stick. Add engine oil if necessary.
CHANGING ENGINE OIL FILTER
1. Park the vehicle on a level surface and apply
the parking brake.
2. Turn the engine off.
3. Place a large drain pan under the oil filter
1.
4. Loosen the oil filter
1with an oil filter
wrench by turning it counterclockwise. Then
remove the oil filter by turning it by hand.
CAUTION
Be careful not to burn yourself. The engine oil
may be hot.
5. Wipe the engine oil filter sealing surface
with a clean rag.
NDI1622NDI16102.0L gasoline engine
8-6Do-it-yourself

10 Technical information
Recommended fluids/lubricants and capacities. . . .10-2
Fuel recommendation..................10-3
Engine oil and oil filter recommendations......10-5
Air conditioner system refrigerant and oil
recommendations....................10-6
Engine specifications....................10-7
Wheels and Tires......................10-8
Dimensions..........................10-9
When traveling or registering in another country . . .10-10
Vehicle identification....................10-10
Vehicle identification number (VIN) plate....10-10
Vehicle identification number (chassis number) . .10-11
Engine serial number..................10-11
F.M.V.S.S./C.M.V.S.S. Certification label......10-11
Emission control information label..........10-11
Tire and loading information label..........10-12
Air conditioner specification label..........10-12Installing front license plate...............10-13
Vehicle loading information................10-14
TERMS..........................10-14
Vehicle load capacity..................10-15
Loading tips.......................10-16
Measurement of weights...............10-16
Trailer towing........................10-16
Uniform tire quality grading................10-17
Treadwear........................10-17
Traction AA, A, B and C................10-17
Temperature A, B and C................10-17
Emission control system warranty............10-18
Reporting safety defects..................10-18
Readiness for inspection/maintenance (I/M) test . . .10-19
Event data recorders (EDR) (if so equipped)......10-20
Owner’s manual/service manual order information .10-20

The following are approximate capacities. The actual refill quantities may be slightly different. When refilling, follow the procedures instructedinthe
“8. Maintenance and do-it-yourself” section to determine the proper refill capacity.
Fluid types Capacity (Approximate) Recommended Fluids and Lubricants
US measure Imp Measure Liter
Fuel tank 13.2 gal
(4WD: 14.8 gal11 gal
(4WD: 12.3 gal)50 L
(4WD: 56 L)
–SeeFuel recommendationlater in this section.
Engine oil (*) The approximate capacities listed are for refilling during an engine oil change. *: For
additional information, seeChanging engine oilin the8. Do-it-yourselfsection.
2.0L gasoline engine:
–Genuine INFINITI engine oil, Viscosity SAE 0W-30
For additional information, seeEngine oil and oil filter recommendationslater in this
section. Drain and refill
With oil filter change 6 qt 5 qt 5.6 L
Cooling system
with Reservoir8.1 qt 6.7 qt 7.6
–Genuine INFINITI Engine Coolant or equivalent in its quality
BASF Glysantin® G40®
–Use Genuine INFINITI Engine Coolant, or equivalent in its quality, in order to avoid
possible aluminum corrosion within the engine cooling system caused by the use
of non-genuine engine coolant.Note that any repairs for incidents with the engine
cooling system while using non-genuine engine coolant may not be covered by the
warranty even if such incidents occurred during the warranty period.
Automatic Transmission Fluid
(ATF)6.6 qt 5.5 qt 6.21 L Shell DCT-M1
Brake fluid Refill to the proper fluid level according to the
instructions in the “8. Maintenance and do-it-
yourself” section.
–Genuine INFINITI brake fluid. DOT 4+ or equivalent.–Never mix different types of fluids.
Differential gear oil 0.8 qt 0.65 qt 0.74 L
–Castrol BOT 355 75W-85
Multi-purpose grease — — —
–NLGI No. 2 (Lithium soap base)
Air conditioner system refrigerant———–HFC-134a
Air conditioner system lubricant———–INFINITI A/C System Oil Type S or equivalent
RECOMMENDED FLUIDS/LUBRICANTS AND
CAPACITIES
10-2Technical information