2017 INFINITI QX30 cruise control

MessagePossible causes/consequences and solutions
[ICC Currently Unavailable
See Operator’s Manual] Intelligent Cruise Control is temporarily inoperative.
Possible causes:
•The function is impaired due to heavy rain or snow.•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The system is outside the operating temperature range.•The on-board voltage is too low.
A warning tone also sounds.
Once the causes listed above no longer apply, the display message goes out.
Intelligent Cruise Control is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away
3. Restart the engine
[ICC Inoperative] Intelligent Cruise Control is faulty. Forward Emergency Braking may also have become inoperative. A warning tone also sounds.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[ICC Suspended] You have depressed the accelerator pedal. Intelligent Cruise Control is no longer controlling the speed of the vehicle. Remove your foot from the accelerator pedal.
[ICC---MPH] An activation condition for Intelligent Cruise Control is not fulfilled.
Check the activation conditions for Intelligent Cruise Control (see Intelligent Cruise Control (ICC) system (Full speed range) (if equipped)
in the 5. Starting and driving section)
[ICC and Speed Limiter Inop-
erative] Intelligent Cruise Control and Speed Limiter are faulty.
A warning tone also sounds.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Cruise Control and Speed
Limiter Inoperative] Cruise Control and Speed Limiter are faulty.
A warning tone also sounds.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Speed Limiter Suspended] While depressing the accelerator pedal beyond the pressure point (kickdown), Speed Limiter cannot be activated. If conditions permit, drive faster than 20 MPH (30 km/h) and store the speed.
Instruments and controls2-49

MessagePossible causes/consequences and solutions
[Cruise Control---MPH] An activation condition for Intelligent Cruise Control is not fulfilled. You have tried to store a speed below 20 MPH (30 km/h), for example.
If conditions permit, drive faster than 20 MPH (30 km/h) and store the speed.
Check the activation conditions for Intelligent Cruise Control (see Intelligent Cruise Control (ICC) system (Full speed range) (if equipped)
in the 5. Starting and driving section)
2-50Instruments and controls

5 Starting and driving
Precautions when starting and driving..........5-4
Exhaust gas (carbon monoxide) ............5-4
Three-way catalyst (if equipped) ............5-4
Tire Pressure Monitoring System (TPMS) .......5-5
On pavement and off-road driving precautions . . .5-10
Avoiding collision and rollover ............5-10
Off-road recovery .................... .5-11
Rapid air pressure loss .................5-11
Drinking alcohol/drugs and driving ..........5-12
Driving safety precautions ...............5-12
All-wheel drive (AWD) driving safety precautions
(if so equipped) .................... .5-14
Infiniti Vehicle Immobilizer system ............5-14
Ignition switch ....................... .5-15
Steering lock ...................... .5-15
Key positions ...................... .5-15
Before starting engine .................. .5-16
Starting engine ....................... .5-16
Starting procedure with the key ............5-16
Driving the vehicle ..................... .5-18
Driving with Automatic Transmission .........5-18
Parking brake .........................5-25
Applying/releasing manually ..............5-25
Applying automatically (vehicles with automatic
transmission) ...................... .5-26Releasing automatically
................5-26
Emergency braking .................. .5-26
Idle Stop/Start System (if equipped) ...........5-27
Automatic engine switch-off ..............5-27
Automatic engine start .................5-28
Deactivating/activating the Idle Stop/Start
function ..........................5-28
L
ane departure warning (LDW) system(if equipped) . .5-29
LDW system operation .................5-30
How to enable/disable the LDW system .......5-31
LDW system limitations .................5-31
LDW system temporarily unavailable .........5-33
System malfunction .................. .5-34
System maintenance ..................5-34
Blind Spot Warning (BSW) system (if equipped) . . . .5-35 BSW system operation .................5-36
How to enable/disable the BSW system ......5-38
BSW system limitations ................5-38
System temporarily unavailable ............5-43
Radar maintenance .................. .5-44
FCC Notice ....................... .5-44
Cruise control ....................... .5-44
Cruise control operations ................5-45

Intelligent Cruise Control (ICC) system (Full speed range)
(if equipped).........................5-47
ICC system operation ..................5-48
ICC switch (cruise control lever) ...........5-49
ICC system display and indicators ..........5-49
Operating ICC ...................... .5-50
ICC Limitations ..................... .5-54
Tips for driving with the ICC system .........5-56
System temporarily unavailable ............5-59
System maintenance ..................5-60
Forward emergency braking (FEB) system (if
equipped) .......................... .5-60
FEB system operation ..................5-61
Turning the FEB system on/off ............5-64
FEB system limitations .................5-65
System temporarily unavailable ............5-65
System maintenance ..................5-66
FCC Notice ....................... .5-67
Active sound enhancement ................5-67
Active sound enhancement ..............5-68
Intelligent Parking Assist (IPA) (if equipped) ......5-68
Important safety notes .................5-68
Detecting parking spaces ...............5-69
Parking ..........................5-70
Exiting a parking space .................5-71
Canceling IPA ...................... .5-73Parking sensor system (if equipped)
...........5-73
Parking sensor overview ................5-75
Range of the sensors ..................5-79
Parking sensor system OFF switch ..........5-79
Parking sensor function settings ...........5-80
Problems with parking sensor system ........5-81
Break-in schedule ..................... .5-81
Fuel efficient driving tips ..................5-82
Increasing fuel economy ..................5-83
Four-Wheel Drive (4WD) (if equipped) ..........5-83
Parking ........................... .5-84
Switching off

the engine ................5-86
Extended parking ................... .5-86
Electric power steering system ..............5-86
Brake system .........................5-87
Brake precautions ................... .5-87
Anti-lock Braking System (ABS) ............5-88
Vehicle Dynamic Control (VDC) system .........5-90
Traction Control System (TCS) .............5-91
Characteristics of VDC ..................5-91
EBD (electronic brake force distribution) ......5-92
Steer Control ...................... .5-92
Hill Start Assist (HSA) ................... .5-93

audible remindersin the9. Maintenance and
Schedules section.
The electric parking brake can only be released
when the ignition switch is in the ON position.
APPLYING AUTOMATICALLY (VEHICLES
WITH AUTOMATIC TRANSMISSION)
The electric parking brake is automatically ap-
plied when:
•Intelligent cruise control (if equipped) brings
the vehicle to a standstill.
or
•Intelligent Parking Assist (if equipped) is
keeping the vehicle stationary.
The red
indicator lamp lights up in the
combination meter.
The electric parking brake is not automatically
applied if the engine is switched off by the Idle
Stop/Start function.
RELEASING AUTOMATICALLY
The electric parking brake can only be released
automatically in vehicles with automatic trans-
mission.
The electric parking brake of your vehicle is
released automatically when all of the following
conditions are fulfilled:
•The engine is running.
•The transmission is in position D (Drive) or R
(Reverse).
•The seat belt is fastened.
•You depress the accelerator pedal.
If the transmission is in position R, the lift gate
must be closed.
If your seat belt is not fastened, the following
conditions must be fulfilled to automatically
release the electric parking brake:
•The driver’s door is closed
•You have shifted out of transmission position
P (Park) or you have previously driven faster
than 2 MPH (3 km/h).
Ensure that you do not depress the accelerator
pedal unintentionally. Otherwise, the parking
brake will be released and the vehicle will start
to move.
EMERGENCY BRAKING
The vehicle can also be braked during an emer-
gency by using the electric parking brake.
While driving, push handle
1of the electric
parking brake. The vehicle is braked as long as
you keep handle
1of the electric parking
brake pressed. The longer the electric parking
brake handle
1is depressed, the greater the
braking force.
During braking:
•A warning tone sounds.
•The [Please Release Parking Brake] message
appears.
•The redindicator lamp in the combi-
nation meter flashes.
When the vehicle has been braked to a stand-
still, the electric parking brake is applied.
5-26Starting and driving

RADAR MAINTENANCE
The two radar sensor unitsAfor the BSW
system are located near the rear bumper. Al-
ways keep the area near the radar sensors
clean.
The radar sensors may be blocked by temporary
ambient conditions such as splashing water,
mist or fog.
The blocked condition may also be caused by
objects such as ice, frost or dirt obstructing the
radar sensors.
Check for and remove objects obstructing the
area around the radar sensors.
Do not attach stickers (including transparent
material), install accessories or apply addi-
tional paint near the radar sensors. Do not strike or damage the area around the
radar sensors. It is recommended you consult
an INFINITI retailer if the area around the radar
sensors is damaged due to a collision.
FCC NOTICE
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation.
NOTE
Changes or modification not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the equip-
ment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause
undesired operation of the device.
Cruise control maintains a constant road speed
for you. It brakes automatically in order to avoid
exceeding the set speed. You must select a
lower gear in good time on long and steep
downhill gradients, especially if the vehicle is
laden or towing a trailer.WARNING
For vehicles with automatic transmission, you
need to have selected manual drive program M
(see
Manual drive program earlier in this sec-
tion). By doing so, you will make use of the
braking effect of the engine. This relieves the
load on the brake system and prevents the
brakes from overheating and wearing too
quickly.
Use cruise control only if road and traffic con-
ditions are appropriate for maintaining a steady
speed for a prolonged period. You can set the
cruise control at any road speed above 20 MPH
(30 km/h).
The speed indicated in the speedometer may
differ slightly from the set speed.
NAA1640
CRUISE CONTROL
5-44Starting and driving

WARNING
•If you fail to adapt your driving style, cruise
control can neither reduce the risk of an
accident nor override the laws of physics.
Cruise control cannot take into account
road, weather or traffic conditions. Cruise
control is only an aid. You are responsible
for the distance to the vehicle in front, for
vehicle speed, for braking in good time, and
for staying in lane.
•Always observe the posted speed limits and
do not set the speed over them.
•Do not use the cruise control when driving
under the following conditions. Doing so
could cause a loss of vehicle control and
result in an accident.– When it is not possible to keep the ve-
hicle at a constant speed
– When driving in heavy traffic
– When driving in traffic that varies speed
– When driving in windy areas
– When driving on winding or hilly roads
– When driving on slippery (rain, snow,
ice, etc.) roads
CRUISE CONTROL OPERATIONS
1Store the current speed or a higher speed
2Store the current speed, or if a speed has
previously been stored, call up the last
stored speed.
3Store the current speed or a lower speed
4Deactivate the cruise control system
When you activate cruise control, the stored
speed is shown in the vehicle information dis-
play for five seconds.
Activation conditions
To activate cruise control, all of the following
activation conditions must be fulfilled:
•The electric parking brake must be released.
•You are driving faster than 20 MPH (30
km/h).
•VDC must be switched on, but not interven-
ing.
Storing, maintaining and calling up a
speed
Storing and maintaining the current speed:
You can store the current speed if you are
driving faster than 20 MPH (30 km/h):
1. Accelerate the vehicle to the desired speed.
2. Briefly press the cruise controller lever up
1or down3.
3. Remove your foot from the accelerator pedal.
Cruise control is activated. The vehicle auto-
matically maintains the speed.
NOTE
Cruise control may be unable to maintain the
stored speed on uphill gradients. The stored
speed is resumed when the gradient evens out.
Cruise control maintains the stored speed on
downhill gradients by automatically braking the
vehicle.
NSD618A
Starting and driving5-45

Storing the current speed or calling up the last
stored speed:
WARNING
If you call up a stored speed and this is differ-
ent from the current speed, the vehicle accel-
erates or brakes. If you do not know what the
stored speed is, the vehicle may accelerate or
brake unexpectedly. There is a risk of an acci-
dent.
Take the traffic conditions into account before
calling up the stored speed. If you do not know
what the stored speed is, store the desired
speed again.
1. Briefly pull the cruise control lever towards you
2.
2. Remove your foot from the accelerator pedal. The first time cruise control is acti-
vated, it stores the current speed or if a
speed has previously been stored, it regu-
lates the speed of the vehicle to the previ-
ously stored speed.
Setting a speed
Bear in mind that it may take a brief moment
until the vehicle has accelerated or braked to
the set speed.
1. Press the cruise control lever up
1for a
higher speed or down
3for a lower speed.
2. Keep the cruise control lever pressed until the desired speed is reached.
3. Release the cruise control lever, The new speed is stored.
4. To adjust the set speed in 1 MPH (1 km/h) increments: briefly press the cruise control
lever up
1or down3to the pressure
point. The last stored speed increases or
decreases in 1 MPH (1 km/h) increments.
5. To adjust the set speed in 10 MPH (10 km/h) increments: briefly press the cruise control
lever up
1or down3beyond the pressure
point. The last stored speed increases or
decreases in 10 MPH (10 km/h) increments.
NOTE
Cruise control is not deactivated if you depress
the accelerator pedal. For example, if you accel-
erate briefly to overtake, cruise control adjusts
the vehicle’s speed to the last speed stored after
you have finished overtaking.
Deactivating cruise control
There are several ways to deactivate cruise
control:
•Briefly press the cruise control lever forward
4.
or
•Brake.
Cruise control is automatically deactivated if:
•The vehicle is secured with the electric park-
ing brake.
•You are driving at less than 20 MPH (30
km/h).
•VDC intervenes or you deactivate VDC.
If cruise control is deactivated, you will hear a
warning tone. You will see the [Cruise Control
Off] message in the vehicle information display
for approximately five seconds.
NOTE
The last speed stored is cleared when you switch
off the engine.
5-46Starting and driving