191
EnGInES And GEAr BO x ES
diesel engine
Euro 6 2.0 litre BlueH
d i 110
2.0 litre BlueH d i 110 S&S2.0 litre BlueH
d i 130
2.0 litre BlueH d i 130 S&S2.0 litre BlueH
d i 160
2.0 litre BlueH d i 160 S&S
Gearbox Manual
(6-speed)
Maximum power (hp) 11 0130 160
EU standard maximum power (kW) 8196120
Cubic capacity (cc) 1 9971 9971 997
Bore x stroke (mm) 85 x 8885 x 8885 x 88
Maximum power engine speed (rpm) 3 5003 7503 750
EU standard maximum torque (Nm) 300340350
Maximum torque engine speed (rpm) 1 5001 7501 750
Fuel DieselDieselDiesel
Catalytic converter Ye sYe sYe s
Particle filter Ye sYe sYe s
Engine oil capacity (in litres)
after draining and replacing the filter 6.6
6.66.6
9
tEcHnIcAL dAtA
diesel engines
192diesel engine
Euro 4 / Euro 5
(
d epending on the country of sale) 2.2 litre H
d i 1102
.2 litre H
d i 130
2.2 litre e-H
d i 1302
.2 litre H
d i 150
2.2 litre e-H d i 1503 litre Hdi 180
Gearbox Manual
(6-speed)
Maximum power (hp) 11
0 130 150180
EU standard maximum power (kW) 819611 0130
Cubic capacity (cc) 2 1982 1982 1982 999
Bore x stroke (mm) 86 x 94.686 x 94.686 x 94.6 95.8 x 104
Max power engine speed (rpm) 3 5003
500 3
500 3 600
EU standard max torque (Nm) 250320350400
Max torque engine speed (rpm) 1
500 2
000 2
000 1 400
Fuel DieselDieselDieselDiesel
Catalytic converter Ye sYe sYe sYe s
Particle filter Ye sNoYe s Ye sYe s
Engine oil capacity (in litres)
after draining and replacing the oil filter 6.2
6.26.29
diesel engines
214
SErVIc I n G
r eservoir
Check and top up the fluid level regularly. Replace the fluid
annually. Replace the fluid if it contains water.
Check the condition of the hydraulic hose and the sealing of the
hydraulic system regularly.
Pump and motor
Requires no servicing, the ball bearings are lubricated for life and
the plain bearings by the pumped fluid.
Lubrication
The tipper body and ram pivots do not have grease nipples.
Lubricate regularly the hinges and retainers for the tipper body sides
as well as the catches for the rear tipper body side.
Sub-chassis and tipper body
For maximum life, we recommend that you clean your tipper body
by washing it down regularly with hose.
Touch-in the paint chips quickly to avoid the spread of rust.
After 8 months of use, check the tightening torque of the
fixings of the underbody to the chassis (following the
recommendations of the body converter).
cleaning the valve slider
● Remove the plug 244A taking care to recover the ball.
●
Using a wide screwdriver
, remove the bore / piston bolt
assembly.
●
Check that the piston slides smoothly and remove any
impurities. Pass a magnet over if there is any swarf present.
●
Refit the assembly and ensure that the piston slides smoothly
.
Retain the ball with some grease on the plug for reassembly.
●
Bleed the hydraulic system.
Bleed the electro-hydraulic unit
● Remove the hexagonal plug 257.
●
Slacken by a half turn the bolt
587 located inside, using a
hexagonal 6 mm spanner.
●
Operate the electro-hydraulic unit for a few moments by
pressing the raise button.
●
The tipper body does not rise, or very slowly
. When fluid flows
from the orifice, the system is bled.
●
Retighten bolt
587 and refit the plug 257, check that the tipper
body lowers correctly.
tipper body
