2017 AUDI A7 brake rotor

co
co
.... N
" N .... 0
00
\.J ' Driving
General information
Breaking in
A new vehicle must be broken in, and the break­
in distance should be 1,000 mi les ( 1,500 km). Do
not drive at speeds that w ill exceed
2/3 of the
maximum permitted engine speed
(RPM) for the
first 600 miles (1,000 km) , and avoid full accel­
eration during this period . You may gradually
start increasing the
RPM and the speed between
600 miles (1,000 km) and 1,000 miles (1,500 km).
During the first hours of use, the engine has a
higher internal friction than later on when all
moving parts have settled into place with each
other.
How the vehicle is driven during the first 1,000
miles (1,500 km) also affects the engine quality.
Drive at moderate engine speeds after the initial
break-in per iod, part icularly when running a cold
engine . This will reduce engine wear and improve
the mileage .
Do not drive at too
low of an engine speed (rpm).
Shift down if the engine stops running "smooth­ ly" . Extremely high eng ine speeds are automati ­
cally reduced .
New tires
If your vehicle is running on new tires, drive pa r­
ticularly careful for the first 350 miles (500 kilo­
meters) after fitting .
.&_ WARNING
-
New tires tend to be slippery and must also
be "broken-in". Be sure to remember this dur­
ing the first 350 miles (500 kilometers).
Brake gently . Avo id following closely behind
other vehicles or other situations that might
require sudden, hard brak ing.
Avoid damaging the vehicle
When you are driving on poor roads, or over
curbs, steep ramps, etc., make certain that low-
D riving
lying parts such as spoilers and exhaust system
parts do not bottom out and get damaged .
T h is is espec ially true for veh icles with low-slung
chass is (sports chassis)* and fully loaded
vehicles.
Warming up/cooling down
Appl ies to: Sand RS models
By warming up/cooling down the engine careful­
ly, you can he lp reduce unnecessary strain on
your vehicle when driving in a sporty style.
The engine speed is limited when the engine is
cold -the full engine output is not available.
When the engine is at operat ing temperature,
the engine speed limitation moves to a higher
RPM range. The tires also only reach their full
road holding capab ility once they have warmed
up .
Your vehicle also has an after-run cooling fea­
ture . However, cooling down is still important.
The engine and the brakes as well as the exhaust
system and the transmission become very hot
when driving in a spo rty style . Before you shut
the vehicle off, you should cool down the vehicle
by driving a few miles at low speeds with light ac­
celeration.
Driving through water on roads
Note the following to reduce the risk of vehicle
damage when driving through water, for example
on flooded roads:
- The water must not be any higher than the bot­
tom of the vehicle body .
- Do not drive faste r than walking speed.
.&_ WARNING
= -
After driving through water or mud, the effec-
tiveness of the brakes may be reduced due to
moisture on the brake rotors and brake pads.
A few careful brake applications should dry
off the brakes .
(D Note
-Vehicle components such as the engine,
transmission, suspens ion or electrical
65

Intelligent Technology
ESC levels
Ap plies to : RS models
Sport mode on ESC/ASRoff Sport mode off or
ESC /ASRon
Beha vior
The ESC and ASR stabiliza-
The stabilization function is The fu
ll stabilization func-
tion funct ions are limited not available
¢ ,& . ESC and tion of the ESC and ASR is
¢ .&. . ASR are switched off. availab le aga in.
Op eration Press the I.$ OFF I button P ress and hold the j.$ OF FI Press the I.$ OFF I button
briefly. b
utton longer than 3 sec- aga in .
onds .
Indicator II turns on . II and Ill turn on. II turns off or II and Ill
light s turn off .
Me ssage s Stabilization control (ESC ): S tabilization control (ESC ): Stabilization control
Sport Warn ing ! Reduced Off . Warning! Reduced sta - (ESC): On
stab ility bility
A WARNING
-Yo u should only sw itch sport mode on or
switch ESC/ ASR off if your dr iving abili ties
and road condi tions permit.
- T he stabilization func tion is limited w hen
spo rt m ode is sw itche d on. The driving
wheels co uld spi n and the vehicle could
swerve, espec ially on s lick or slippery road
s u rfaces.
- T here is no vehicle sta bilizat ion when E SC/
ASR a re swi tched off.
(D Tips
- ES C/ASR can not be switc hed off or sport
mode cannot be switche d on if the cr uise
contro l system * or the adap tive c ruise con­
tro l* is switched on.
- If the re a r spoiler sys tem m alf unct ions,
sport mo de may not switch on or it may
switc h off aga in automatically.
Braking
New brake pads
New b rake pads do not ac hieve the ir full b raking
effe ct during the firs t 2S 0 mi (400 km). They
m ust be "broken in" fi rst .
The b rea k-in period ca n be considerably longe r
for ve hicles w it h cer amic b rake rotors*. However,
you can compensa te fo r the slightly reduced
122
braking force by pressing firmly on the brake
pedal. Avo id heavy braking during the break-in
per iod.
Wear
Brake pad
wear depends large ly on the way the
vehicle is driven and on ope rating conditions .
This is espec ia ll y true if you a re driv ing frequent ly
i n the city and on curves or with a sporty driving
sty le .
Ope rating noi se
Noises may occur when braking depending on the
speed, braking force and outside conditions such
as temperature and humid ity.
Noises may become mo re apparent at lower
speeds due to the nature of the materials in the
ceram ic brake rotors* .
Effect of water and road salt
In certain situa tions, for e xamp le after d riving
thro ugh water, in heavy rain, a fter over nigh t con­
densation or after washing your car, the brak ing
effect can be reduced by moisture or ice on the bra ke rotors and brake pads. The brakes must be
"dried" f irst with a few ca refu l brake app lica­
tions.
At higher speeds and with the windshield wipers
turned on, the brake pads press against the brake rotors for a short amount of time. This action,
wh ich is not felt by the dr iver, happens at regu lar .,..

co
co
.... N
" N .... 0
00
\.J ' intervals and ensures a better reaction time fo r
the brakes in wet weather.
The braki ng effect can also be red uced if you are
driving on salted roads and you do not apply the b rakes for long periods of time . The layer of salt
on the brake rotors and pads must be worn off
f irst when the brakes are app lied.
Due to its surface, the ceramic bra ke rotor* ab­
sorbs moisture in certa in situations. There fore,
there will temporarily be less braking force than
when the brakes are dry . You can compensate for
this by pressing the brake pedal harder.
Cor rosion
L eaving the vehicle parked fo r long periods of
time, low mi leage and avoiding heavy braking
can contribute to corrosion on the brake rotors
and to dirty brake pads.
I f you usually avo id heavy braking or if there is
corrosion present , occasional heavy braking at
high speeds is recommended to clean the brake
rotors and pads
q ,& .
Brak e system malfunct ion
if you notice that the brake pedal travel has sud­
denly increased, then a brake c ircui t in the dual­
circuit brake system may have malfunctioned. Drive to an authorized Audi dea ler or a uthorized
Aud i Service Facility immediately to have the
problem corrected. On the way there, drive with
reduced speed and keep in mind that you w ill
need a longer distance to stop and you w ill need
to p ress the b rake pedal harde r.
L ow brake fluid level
When the brake fl uid level is low, malfunct ions in
the brake system may occur . The brake f lu id level
is electronically monitored.
Br ak e boost er
The brake booster amplifies the pressure you ap­
p ly to the brake peda l. It only works when the en­
g ine is running.
A WARNING
- Only apply the brakes for the purpose of
cleaning the brake system whe n road and
-
Intellig ent Technology
traffic conditions permit. You must not en­
danger other road users. This increases the
risk of an accident.
- Never let the vehicle roll while the engine is
stopped because this increases the risk of an
accident.
- New brake pads do not ach ieve the ir full
braking effect during the first 250 m i
(400 km). They m ust be "broken in" first.
The break-in per iod ca n be cons iderably lon­
ge r fo r vehicles with ceram ic brake rotors* .
H owever, you can compensate fo r the
slightly reduced braking force by pressi ng
fi rm ly on the brake pedal. Avo id heavy b rak­
ing du ring the break -in pe riod.
- Ce rtain weathe r and ope rating condi tions
such as driving through water, dr iv ing in
heavy rain o r driv ing after was hing your ve­
hicle can impa ir the effect iveness of the
brakes. In the winter, ice may build up on
the brake pads, rotors and drums . Check
these components by braking carefully. Ap­
p lyi ng the brakes carefully several times
d ries the b rakes and removes ice build-up .
- The efficiency of the brakes can also be im­
pa ired by dr iv ing for long stretches on roads
covered with sa lt without using the bra kes .
You can remove salt deposits from the
b rake rotors and pads by carefully applying
t he brakes several times .
- I f the fron t spoiler is damaged o r yo u install
another spoi ler, make su re the front wheel
b rakes are ven tilated properly . Othe rw ise,
the brake system co uld overheat, which re­
duces their effectiveness .
- Fa ilure of a brake circuit impairs brak ing
pe rformance, which increases b raking dis­
tance. Avo id driving the vehicle and have it
towed it to the nearest a uthorized Audi
deale r or authorized Aud i Serv ice Facility.
- I f the brake booster is not working, yo u w ill
have to p ress much harder on the brake
pedal to compensate fo r the lack of the
booster.
Q) Note
- Never let the brakes "rub" by pressing the
peda l lightly when braking is not actually
123

Care and cleaning
A WARNING
- Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the braking effect
may be delayed due to mo isture on the
brake rotors or ice in the winter . This in­
creases the risk of an acc ident. The brakes
must be d ried first w ith a few careful b rake
applications.
(D Note
- If yo u wash the ve hicle in an automatic car
wash, yo u m ust retract the rear spoiler if
necessary, and fold the exte rior mi rrors in
to reduce the risk of da mage. Power fo ld ing
ex ter ior mirro rs* m ust only be folded in and
out using the power folding func tion.
-
- To red uce the risk of pa int damage, do not
wash the vehicle in direct sun light .
- T o reduce the risk of damage to the s urface,
do not use insect removing sponges, kitchen
sponges o r similar items .
- Matte finish painted vehicle components:
-To reduce the risk of damage to the sur-
face, do not use polis hing agents or hard
wax .
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint. The paint could be damaged
when the stickers or magnets are re­
moved.
@ For the sake of the environment
Only wash the veh icle in facili ties spec ially de­
s igned for that pu rpose . This will reduce the
r isk of dirty wate r contam inated with o il from
ente ring the sewe r system.
Cleaning and care information
W hen clean ing and ca ring for ind ividua l vehicle
components, refer to the fo llow ing tables. The
i n formation conta ined there is s imply recom­
mendations. For quest ions or for components t
h at are not listed, cons ult an autho rize d Aud i
dealer or au thor ized Aud i Servi ce Fac ility. Also
fo llow the informa tion found in <=> & .
Ext erior cleaning
Component Situation Solution
Windshield wiper
Deposits ¢ page 47, Cleaning windshield wiper blades
blades
Headlights /
Deposits Soft sponge wi th a m ild soap solution3>
Tail light s
Sensors /
Deposits Sensors: soft cloth with solvent-free cleaning solution
camera lens es Camera lenses: soft cloth w ith alcohol -free cleaning solu -
tion
Snow/ice Hand br ush/solvent-free de-icing spray
Wheels Road salt Water
Bra ke dust Acid-free special cleaning solution
Exhaust tail pipes Road salt Water, clea ning solution su itab le for s tainl ess stee l, if nee-
essa ry
236

co
co
.... N
" N .... 0
00
<.,;) 'SI"
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel.
Fig. 207 Changing a wheel: using the screwdriver hahd le
(with the blade removed} to turn the bolts
F ig. 208 Changing a wheel: alignment pin ins ide the top
hole
After you have loosened all wheel bo lts and
raised the vehicle
off the ground, remove and re­
p lace the whee l as follows:
Removing th e wheel
" Use the hexagon al so cket in the screwdri ver
handle to completely remove the topmost
wheel bolt and set it aside on a
clean surface
¢fig. 207.
.. Screw the threaded end of the alignment pi n
from the tool kit hand-tight into the empty bolt
hole
¢ fig. 2oa1>.
" Then remove the other wheel bolts as described
above .
" Take
off the wheel leaving the a lignment pin in
the bolt ho le
¢ 0 .
l) Applies to vehicles with ceram ic brake rotors•: Use a sec­
ond alignme nt pin• (stored in t he spa re wheel well mold ­
ing} for the lower hole , fo llow ing the descript ion for the
first alignment pin.
Em ergen cy a ssis tanc e
Putting on th e spar e wheel
" Lift the spare whee l and caref ully slide it over
the alignment pin to guide it in place¢(!).
.. Use the hexagona l socket in the screwdriver
handle to screw in and tighten all wheel bolts
slightly .
"Remove the alignment pin and insert and tight­
en the remaining wheel bo lt slightly like the
rest .
.. Turn the jack hand le counter-clockw ise to lower
the vehicle unt il the ja ck is fully released.
" Use the wheel bo lt wrench to t ighten a ll wheel
bolts firmly¢
page 245. Tighten them cross­
wise,
from one bo lt to the (approx imately) op­
posite one, to keep the wheel centered.
(D Note
When removing or installing the wheel, the
rim could hit the brake rotor/ceramic brake
rotor* and damage the rotor . Work carefully
and have a second person he lp you.
(D Tips
Never use the hexagonal socket in the hand le
of the screwdriver to loosen or tighten the
whee l bolts.
- Pull the reversible blade from the screwdr iv ­
er before you use the hexagona l socket in
the handle to turn the wheel bolts.
- When mounting tires with unidirectional
t read de sign make sure the tread pattern is
pointed the right way
¢ page 248.
- The wheel bolts sho uld be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
247

Index
Remote con trol key . . . . . . . . . . . . . . . . . . . 30
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Sunroof. ... .. .. ... ... .... ... .. .. .. .. 37
Ce ramic brake rotors
N ew b rake pads . . . . . . . . . . . . . . . . . . . . . 122
Cert ification . . . . . . . . . . . . . . . . . . . . . . . . . 267
Changing engine oil . . . . . . . . . . . . . . . . . . . 205
Ch ild rest raints
D anger o f using ch ild rest raints in the front
seat ... .. .... ... .. .. ..... ... .. .. .. . 14 9
Where can I get additional information
about child restraints and their use? . . . . 190
Ch ild rest raint system a nchors . . . . . . . . . . 186
Ch ild safety . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Important safety instructions for using child
safety sea ts . . . . . . . . . . . . . . . . . . . . . . . . 176
I mportant things to know when driving with
chi ldren . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Tether anchors . . . . . . . . . . . . . . . . . . . . . . 189
Tether straps . . . . . . . . . . . . . . . . . . . . . . . 189
Ch ild safety lock
P owe r wi ndows . . . . . . . . . . . . . . . . . . . . . . 36
Rea r doo rs . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Ch ild safety seats
Booster seats . . . . . . . . . . . . . . . . . . . . . . . 182
Convertible ch ild seats . . . . . . . . . . . . . . . 180
Conve rtible locking retractor . . . . . . . . . . 185
H ow do I properly install a child safety seat
i n myve hicle? . .. ............. .... .. . 176
I nfan t sea ts . . . . . . . . . . . . . . . . . . . . . . . . 178
I nsta lling a child restraint using the LA TCH
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
L ATCH system . . . . . . . . . . . . . . . . . . . . . . 188
Lower anchorages . . . . . . . . . . . . . . . . . . . 187
Mounting and releasing the anchorage
hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Safety instructions . . . . . . . . . . . . . . . . . . . 176
Unused safety belts on the rear seat . . . . 178
Ch ild seats . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Secur ing . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Cigaret te lighter . . . . . . . . . . . . . . . . . . . . . . . S2
Clea ning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Cleaning/remov ing ice from windows . . . . . 237
C le ani ng Alcanta ra . . . . . . . . . . . . . . . . . . . . 238
Clean ing artificia l leather . . . . . . . . . . . . . . . 238
Cleaning carbon parts . . . . . . . . . . . . . 237, 238
C lea ning contro ls . . . . . . . . . . . . . . . . . . . . . 237
270
Cleaning decorative pa rts/trim . . . . . . . . . . 237
Cleaning disp lays . . . . . . . . . . . . . . . . . . . . . 23 7
Cleaning exhaust tail pipes . . . . . . . . . . . . . 236
C leaning plas tic pa rts . . . . . . . . . . . . . . . . . . 23 7
Cleaning r ims . . . . . . . . . . . . . . . . . . . . . . . . 236
Cleaning textiles . . . . . . . . . . . . . . . . . . . . . . 238
Cl imate contro l system . . . . . . . . . . . . . . . . . S9
A utomat ic au xiliary heater . . . . . . . . . . . . . 63
A utomat ic rec irculat ion . . . . . . . . . . . . . . . . 63
Bas ic settings . . . . . . . . . . . . . . . . . . . . . . . . 63
Drive select. . . . . . . . . . . . . . . . . . . . . . . . . lOS
Closi ng
Hood .............................. 201
Su nroo f... .... .. .. .. ... .......... .. . 37
Windows ... .. .. .. .. .. . ... .... ... .. . 36
Closi ng/ope ning
By remote control . . . . . . . . . . . . . . . . . . . . 30
With the centr al locki ng sw itch . . . . . . . . . 31
Wi th the convenience key . . . . . . . . . . . . . . 30
Closing aid (doors) . . . . . . . . . . . . . . . . . . . . . 27
Closing and opening With the door lock . . . . . . . . . . . . . . . . . . . . 32
Cockpit (overview) . . . . . . . . . . . . . . . . . . . . . . 6
Co lor code . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Coming home . . . . . . . . . . . . . . . . . . . . . . . . . 42
Compartments . . . . . . . . . . . . . . . . . . . . . . . . 53
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 267
C ons umer in formation . . . . . . . . . . . . . . . . . 2 64
Cons umer Information . . . . . . . . . . . . . . . . . 136
Cons umption (fuel) . . . . . . . . . . . . . . . . . . . . 22
Contacting NHTSA . . . . . . . . . . . . . . . . . . . . 13 6
Convenience key
Start ing the engine (START ENGINE STOP
button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Stopp ing the eng ine (STAR T ENGIN E ST O P
button) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Swi tc hi ng the igni tion on . . . . . . . . . . . . . . 69
Unl ocking/locking . . . . . . . . . . . . . . . . . . . . 30
Convenience opening . . . . . . . . . . . . . . . . . . . 37
Convertible child safety seats . . . . . . . . . . . 180
Convertib le locki ng ret racto r
Activ ati ng . . . . . . . . . . . . . . . . . . . . . . . . . . 18S
Deact ivating . . . . . . . . . . . . . . . . . . . . . . . . 186
U sing to secure a child safety seat . . . . . . 185
Cooling down . . . . . . . . . . . . . . . . . . . . . . . . . 6S